On Ericsson Ltd in Borås a wireless communication system called MINI-LINK? is produced. In order to sell their product with the best possible quality guaranty, there is a signal processing circuit called ATLAS implemented in the system. This circuit would eventually be useful in the production and for the repairs of the radio units. Our commission was to examine the possibility for this use.

In Sweden the amount of people with obesity has increased with almost 50 % during the past 20 years and is now including 500 000 people. A larger energy intake than energy consumption is today one of the most important cause of overweight and obesity that exist in the world. This requires more knowledge about healthier eating habits combined with moderate intensive exercise, exercise that is simple, effective and amusing. A god solution is a combination of fitness training and strength training, a type of circuit training. It is distinguished by a high intensive work in short periods and with a short break.

In this thesis a number of energy saving methods for a multiplier on algorithmic level are investigated. For the investigation a multiplier is constructed in VHDL, after which the circuit's performance is investigated. A number of techniques for reduced power consumption are introduced in the circuit and are then evaluated. The conclusions are that all investigated methods, pipelining, interleaving and voltage scaling, should be maximally made use of in order to minimize the power consumption..

To measure losses in a transformer with today?s methods is either slow or insecure. There s a new method developed by Alstom that hasn't been actualize in to a test-system and that has been the assignment in this project. The idea is built on a switched system and a CLR- circuit in the resonant frequency. The test-system has a calculated power-loss that make the efficiency to be as high as 99,8% and in reality over 95%.

This is a thesis about The Eight Circuit Model, a modern mind map developed for the purpose of illumination and enlighenment by Dr. Timothy Leary in the 1970s. Later, authors such as Robert Anton Wilson and Antero Alli elaborated upon the idea to make it more wholesome and compatible with other ideas expressing the same basic principle. In short, it is an intellectual abstraction of the evolution of consciousness through a series of eight stages, which Leary called Circuits. By looking at the brain as an evolving bio-computer, with thoughts working as software, upgrading itself through neurological imprints, Learys created a Hero's Journey for the modern age.The thesis tries to analyze this idea, as it is presented in Robert Anton Wilsons Prometheus Rising, through the lens of the discourse category ?Western Esoterism.? A hard-to-define subject but described as ?the dialectic of the hidden and the revealed in the field of religion.?.

Electronic article surveillance (EAS) is widely used in shops and libraries together with an RF-tag attached to the goods or books in order to prevent shoplifting. By implementing the addition of a moisture sensor to the RF-tag, other functions become possible, including the ability to use as an alarm with regards to frozen goods, which have been shipped but which have melted and have, subsequently, refrozen. In- relation to care for the elderly, one time-consuming step involves checking whether there is the necessity for a change of diaper and this can, instead, be based on an RF-tag with an EAS-system alarm. A preliminary investigation was made using the moisture sensors, which involved how the resistance changes when liquid and/or heat is applied. A simulation of the LCCR circuit (RF-tag with the sensor) was conducted in order to determine how the resonance frequency changes for different resistances levels.

Development in spin dynamic occurs in the whole world because of therising demands on fast electronic storage for example hard drivesand RAM (Random Access Memory). Measuring the spin resonance of amaterial gives you the insight of the theoretical speed for amagnetic memory. This means the maximum storage speed is below thefirst resonance. All magnetic materials have different propertiesthat will inflict the resonance frequency which brings that theconstructors of memories need to know which magnetic material theywill use to obtain best results. In the market for normal users themaximum storage speed in a RAM memory is 1.6 GHz.

The purpose of this thesis has been to determine experimentally how good a peltierelement is to convert waste heat from wood burning. Three different peltier elementswere used in a comparison study. The comparison was mainly done to know howmuch power could be obtained from each element. Even, a circuit with a step-upfunction has been created to give a higher output voltage than the peltier elementitself. The result of the experiments was a low output power, the highest valuereached 2.18W.

Storing kinetic energy in a flywheel allows for more efficient driving of electricvehicles. Research in this area is in progress at Uppsala University, where a flywheelwith magnetic bearings encased in a vacuum chamber is being constructed. To makethis possible methods for measuring the current through the electromagnets in thebearings and temperatures in the flywheel need to be developed. This has been thepurpose of this report. The current measurement resulted in a resistive method, andthe implementation of eight measurement circuits in the system.

The Rya power plant in Borås produces district heating, district cooling and electricity. The plant is owned by Borås Energi och Miljö AB and is run by Dalkia Facility Management AB.In order to get the best heat exchange from the district hot water a pair of twin pumps and a turbine circuit pump are used as return pumps. Turbine circuit pumps are used to increase the pressure through the heat exchangers at the power plant. The pumps are in use when the flow is over 2 000 m3 h-1 and during the summer when re-cooling is used to improve the effectivens of the heat boilers.Since the pumps, that are parallel connected, rotating at a fixed rate per minute, the pressure is regulated with regulating valves. This report shows that during the 4,300 hours that the pumps where in use, energy corresponding to 590 MWh was wasted.

This bachelor thesis is about an ultrasonic sensor, implemented in a bubble chamber in Artis. The sensor consists of the piezoelectric sensor and an electronic control circuit. The control circuit consists of a programmable microprocessor, PIC18F2420 and a circuit, which sends the excitation signal to the piezoelectric sensor, and later receives the echo. This bachelor thesis consists also of a theoretical study, which examines different techniques of liquid level sensing in a chamber. The study discusses which factors are important in liquid level sensing and examine accepted methods.

Ericsson AB in Katrineholm is a part of the Section Business Unit Network in the Ericsson Group. The plant's main task is to produce printed circuit boards in small volumes with a high product mix and focus on delivery and cost effectiveness. At the factory they produce printed circuit boards in the Module department.The Module department has for a long time had a high output of non-approved circuit boards in their production. This has led to a growing stock of non-approved circuit boards on the company?s repair department.The purpose of this thesis is to investigate how Ericsson in Katrineholm can increase the outflow of approved articles in their test process in the Module department.

In this Master thesis, microwave connections between circuit boards are constructed. The primary frequency band is the X-band (8-12 GHz). The purpose of the connections is to enable a more simple and cheaper way of mounting the circuit boards inside a container. The connections have been designed and evaluated, using different computer programs. A few prototypes have been built and measured.

In this Master thesis, microwave connections between circuit boards are constructed. The primary frequency band is the X-band (8-12 GHz). The purpose of the connections is to enable a more simple and cheaper way of mounting the circuit boards inside a container. The connections have been designed and evaluated, using different computer programs. A few prototypes have been built and measured.

In this Master thesis, microwave connections between circuit boards are constructed. The primary frequency band is the X-band (8-12 GHz). The purpose of the connections is to enable a more simple and cheaper way of mounting the circuit boards inside a container. The connections have been designed and evaluated, using different computer programs. A few prototypes have been built and measured.