The report descripbs how a diplexer for a hybrid analog/digital filterbank has been constructed and tested. A diplexer divides the frequency band into two different bands that do not who doesn't overlapp each other. The sampling rate for the two ADC:s is 80 Msps, and therefore it is advantage to have zero at 80 MHz. The reason for this is that a proposed class of hybrid filterbanks with very good quality requires a zero at or close the sampling frequency to work well. The diplexer was made in three versions.

In this Master thesis, microwave connections between circuit boards are constructed. The primary frequency band is the X-band (8-12 GHz). The purpose of the connections is to enable a more simple and cheaper way of mounting the circuit boards inside a container. The connections have been designed and evaluated, using different computer programs. A few prototypes have been built and measured.

The thesis was performed at the lighting company Zpecta AB. Zpecta needed to develop alternative attachment of their LED-luminaire Capella. Today Capella attaches in metal ceilings with four magnets. Zpecta got indications from their customers that there was a need for other attachments. The purpose is to determine the customer?s requirements and the interfaces that are considered for Capella.During the thesis, Capella was only on the market for testing and evaluation.The thesis was initiated to create a specification.

The purpose of this degree project was to build laboratory equipment for a new course in power electronics that starts this autumn 2010 at Uppsala University. The equipment is intended for student labs and it covers the most important areas of the course including rectifying, buck-/boost-converters and PWM-modulation. It is built as one sealed unit where all the electronics are built-in but visible and it has a connection board where students safely can connect the different circuits. The project has advanced from theoretical studies of circuit design, choosing of components and simulations to drawing the printed circuit board (PCB), soldering, case building, final testing and troubleshooting - basically most steps from an early idea to a final product. Measurements on the final product gave about the same results as the earlier simulations of the circuits and the result is overall satisfying..

Today?s environmental discussions have led to more progress in the different transportareas. To ride a bicycle is often one of the most efficient alternative when it comes totransport. An Electric bike is, and makes transportation more efficient than a regularbicycle. Electric bicycles do not affect the environment significantly and allows moreconvenient transportation than ordinary bicycles do.

Automationscenter & Bråvalla Elteknik AB is a company that offers the market completed total solutions where the customer can operate and monitor their production from the terminal. In these total solutions they lack standard circuit which are developed by the company and which could manoeuvre/control/monitor controlled process objects. This report defines the work of developing the most common standard circuits.The report is initiated by a short theoretical part about PLC and the PLC system, with a connected terminal, which has been used. Thereafter, the turnout of the demands of specification is reported, after discussing with the supervisor in the course of the project. The report concludes with a disclosure of how the programming, the documentation and the testing have proceeded and a final discussion concerning the project and proposals on continuation.The result is a CD with the documentation of standard circuits and how they are implemented in a new project.

Gunsta is situated about 10 km east of Uppsala. Today there are plans to establish 1000 new households in Gunsta before year 2030. The required energy for heating houses and water would be distributed via a district heating system, which also includes 200 existing residences. The annual required energy, according to this study, would be 16.2 GWh with a maximal peak effect of 6.9 MW. To meet this need, the study suggests a system with heat pumps to upgrade the 31?C water from a 1.8 kilometre deep borehole.

A degree project has been carried out at Motion Control, Västerås. The degreeproject ?Grafisk Skärm för Inbyggda System? have developed a first prototype of anembedded system with a display, a graphical user interface with touchscreen andpossibilities to communicate with external units.The work initiated with surveys of critical components. A technical specification forthe desired end product was developed. With the technical specification as support,design specifications for hardware and firmware were developed.After the specifications were done, a circuit diagram was developed and a circuitboard was made.

For several years Uppsala University together with several companies has been involved in a WISENET project aimed at improving railway transport security. By placing a sensor system near the wheels of each wagon, the temperature of the bearings can be measured and transmitted to a collector placed centrally on the wagon. This in turn transmits the collected data to RFID receivers placed intermittently along the railway.As the signals are transmitted wirelessly, problems may occur as the antennas get dirty or coated with ice and snow. To determine the effects of these coatings, several tests were performed examining the reflection coefficient S11, the impedance Z11 and the efficiency eta of an antenna, and how they varied when various coatings were placed over the antenna. Examined coatings were ice, snow and water to determine the effects of weather, and various metal-based coatings: powdered iron both pure and partially oxidized, and iron ore granules.

Mechanical relays are more and more being replaced with semiconductortechnology. In this thesis it is investigated if and how the larger loads couldbe controlled by transistors. The main part of this work aims to create andverify a solution that can control the starter motor, as well as protect it incase of any failure. The different malfunctions that the solution protectsagainst is high current, too high peak current, low current, maximum cranktime and minimum cool off time. The timers also protect indirectly againstoverheating of the starter engine.The transistors used are BTS555, from Infineon.

For several years Uppsala University together with several companies has been involved in a WISENET project aimed at improving railway transport security. By placing a sensor system near the wheels of each wagon, the temperature of the bearings can be measured and transmitted to a collector placed centrally on the wagon. This in turn transmits the collected data to RFID receivers placed intermittently along the railway.As the signals are transmitted wirelessly, problems may occur as the antennas get dirty or coated with ice and snow. To determine the effects of these coatings, several tests were performed examining the reflection coefficient S11, the impedance Z11 and the efficiency eta of an antenna, and how they varied when various coatings were placed over the antenna. Examined coatings were ice, snow and water to determine the effects of weather, and various metal-based coatings: powdered iron both pure and partially oxidized, and iron ore granules.

Ett stort antal människor dör på grund av skador som de fått inom vården och som hade kunnat förebyggas. Det finns siffror som pekar på att dessa vårdskador överskrider antalet döda i trafiken. Vid Östergötlands landsting finns sedan år 2005 en fast enhet som arbetar med patientsäkerhet. En av deras uppgifter är att, tillsammans med berörd verksamhet, utföra händelseanalyser inför anmälningar av Lex Maria-fall. Den analysmetod som används av patientsäkerhetsenheten är uppbyggd på en epidemiologisk olycksmodell.Syftet med denna studie har varit att använda analysmetoden FRAM (Functional Resonance Accident Model), som är en systemisk analysmetod utarbetad av Erik Hollnagel, i en vårdrelaterad kontext, någonting som inte har gjorts tidigare.

Målet med detta examensarbete, utfört på uppdrag av Vectura Consulting AB, har varit att undersöka möjligheten att ansluta en vindkraftpark till järnvägens kontaktledningsnät. Möjligheten att koppla om vindkraftparken till järnvägens hjälpkraftnät, som bland annat förser växelvärmare och signalsystem med effekt, har också undersökts. Eftersom kontaktledningsnätet och hjälpkraftnätet arbetar med olika frekvenser och spänningar, 16? Hz och 15 kV respektive 50 Hz och 22 kV, måste därför en komplett krets för frekvensomvandling, spänningsomvandling och omkoppling tas fram. Projektet har begränsats till en del av Botniabanan, sträckan Örnsköldsvik-Nordmaling.I denna rapport har trafikfrekvensen på den valda sträckan på Botniabanan undersökts för att bestämma en genererad effekt till inkopplingspunkten, samt för att undersöka när det kan vara lämpligt att koppla om till hjälpkraftnätet.

Målet med detta examensarbete, utfört på uppdrag av Vectura Consulting AB, har varit att undersöka möjligheten att ansluta en vindkraftpark till järnvägens kontaktledningsnät. Möjligheten att koppla om vindkraftparken till järnvägens hjälpkraftnät, som bland annat förser växelvärmare och signalsystem med effekt, har också undersökts. Eftersom kontaktledningsnätet och hjälpkraftnätet arbetar med olika frekvenser och spänningar, 16? Hz och 15 kV respektive 50 Hz och 22 kV, måste därför en komplett krets för frekvensomvandling, spänningsomvandling och omkoppling tas fram. Projektet har begränsats till en del av Botniabanan, sträckan Örnsköldsvik-Nordmaling.I denna rapport har trafikfrekvensen på den valda sträckan på Botniabanan undersökts för att bestämma en genererad effekt till inkopplingspunkten, samt för att undersöka när det kan vara lämpligt att koppla om till hjälpkraftnätet.

Målet med detta examensarbete, utfört på uppdrag av Vectura Consulting AB, har varit att undersöka möjligheten att ansluta en vindkraftpark till järnvägens kontaktledningsnät. Möjligheten att koppla om vindkraftparken till järnvägens hjälpkraftnät, som bland annat förser växelvärmare och signalsystem med effekt, har också undersökts. Eftersom kontaktledningsnätet och hjälpkraftnätet arbetar med olika frekvenser och spänningar, 16? Hz och 15 kV respektive 50 Hz och 22 kV, måste därför en komplett krets för frekvensomvandling, spänningsomvandling och omkoppling tas fram. Projektet har begränsats till en del av Botniabanan, sträckan Örnsköldsvik-Nordmaling.I denna rapport har trafikfrekvensen på den valda sträckan på Botniabanan undersökts för att bestämma en genererad effekt till inkopplingspunkten, samt för att undersöka när det kan vara lämpligt att koppla om till hjälpkraftnätet.