The supply of uninterruptible power can be applied to many areas wherecontinuous operation is highly prioritized.The application of uninterruptible power for motor operation is facilitatedusing a frequency converter. Direct current operated frequency converters canbe applied directly to the power reserve which removes the need for additionalpower-converting.Batteries have long constituted the power reserve but advancements inthe development of ultracapacitors have created a viable substitution. Ultra-capacitors have high energy storing capabilities and can be applied to highpower applications.Maxwell is a leading manufacturing company of ultracapacitors and pro-vide different modules with built-in solutions for voltage balancing. Unevenvoltages between series-connected capacitors is a phenomenon caused by vary-ing capacitance. A configuration containing Maxwell?s 56V module is createdand constitutes the power reserve in the simulations.The discharge simulation shows a significant current that could damagethe system.

This report is an outcome of a master degree project at Linköpings University in co-operation with Micronic Laser Systems AB. The purpose with this master degree project was to investigate how to implement a receiver in a data transfer system. The system consists of several data channels, where every channel consists of three parts: driver, transmission lines and receiver. The driver send low amplitude differential signals via the transmission lines to the receiver that amplifies and converts it to a single-ended signal. The receiver has to be fast and be able to feed an output signal with high voltage swing.

The change in course recently taken by the Swedish Armed Forces results in an increased use of equipment, and thereby increased requirements of preventive maintenance. This paper aims to examine the current responsibilities for preventive maintenance in an army unit. The intended effect of this examination is to disclose possible flaws, and to help make routines for preventive maintenance more effective.The questions asked in this paper are;Who, in an army unit, is responsible for the routine maintenance?When is this responsibility valid?What demands does the technical service have on responsibilities for the routine maintenance?How are these demands met?How ought to be responsible for the routine maintenance?To answer these questions the author has chosen to use a descriptive method to show the current facts. A theorizing method is chosen to, from described facts, clarify the demands of the technical service on routine maintenance.

In 2013 a new emission standard for heavy trucks was introduced and hence a number of new parts was brought in to Scania CV AB. This created a need for modifications in the silencers flow. The flow is highly complex involving several suppliers, call off methods and different models of silencers. The aim for this project was to improve the existing silencers flow. The flow, from supplier to assembling, has therefore been mapped.

An array of different retinal disorders is present as a threat in quite a number of dog breeds. These often lead to profound visual impairment or blindness. Many of the disorders are genetic, and they are, in Sweden as well as in other countries, subject to breeding programmes. The anatomy of the eye and the retina, as well as current examination techniques (ophthalmoscopy, electroretinography (ERG) and genetic analysis) are described. The more common retinal disorders encountered in dogs in Sweden are discussed: retinal dysplasia, generalized progressive retinal dystrophy, retinal pigment epithelial dystrophy, collie eye anomaly, sudden acquired retinal degeneration, retinal detachment and choroiditis. The possibly affected breeds are listed. The value of diagnostic findings is discussed and current advances on the subject in ophthalmologic research are accounted for..

A manufacturing machine at the engineering company Sandvik Coromant has a positioning table which task is to move an item linearly. The positioning table has a linear motor capable of high velocity and acceleration. This makes it possible to achieve short cycle times and a more profitable production.The purpose of this thesis is to bring forward a new concept which is more adapted to the requirements of the positioning table. The reason is that the current positioning table provides an unnecessarily positioning accuracy of 0.01 mm, while the requirement for the positioning accuracy is just 0.1 mm. The goal is to reduce manufacturing and component costs.To develop a suitable solution an approach for the concept development process has been performed.

The report examines the factors which may be a contributing cause to the problems that are present when ferritic stainless steel are eddy current tested in a warm condition. The work is carried out at Fagersta Stainless AB in Fagersta which manufactures stainless steel wire. In the rolling mill there is an eddy current equipment for detection of surface defects on the wire. The ferritic stainless steels cause a noise when testing and this noise complicates the detection of defects.Because of this, a study was made of how the noise related to factors such as steel grade, temperature, size and velocity. By observing the signal and with the possibilities to change the equipment settings the capability to let a signal filter reduce the noise level were evaluated.

This rapport is result of a project. The purpose of which was to design a circuit that is used in a heat glove. The heat glove is the technical aid which provides heat inside a glove.It is specially suited for old people who have problems with cold hands because of decreased blood circulation.There already was an old circuit in the glove that gives a constant current which develops heat from battery to glove through a circuit. The temperature is between 32 and 34 degrees.The problem with the existing circuit was to regulate the temperature. There is only on/off switch and there is no way to adjust desirable value of the temperature.In order to solve the problem the old circuit was investigated.

At nuclear power plants, electrical valve actuators are important for ensuring that the reactor core is water covered and the pressure in the reactor tank and containment is limited. The electrical actuators are provided with overload protection in case of drawing higher current then the motors are rated for. When safety manoeuvres are needed, the overload protection must not trig and cause the valve to stop before completing the manoeuvre. Analyses have showed that the current settings of the overload protection may cause an illegitimate trig at the worst theoretically possible accident. A new method has been developed with conservative assumptions and applies overload protections for all electrical valve actuators at the three reactors in Forsmark..

This bachelor thesis aims to analyse the Swedish mortgage market and investigate whether it is in a current price bubble or not. Comparisons have been made with Denmark, a country with a market similar to Sweden?s, and where the mortgage market faced a price bubble that crashed in 2008. The housing market in Stockholm has been analysed as a separate market, as it differs from Sweden as a whole in prices and underlying factors to increased prices. The conclusion of this thesis is that not Sweden, nor Stockholm, is currently in a price bubble at the mortgage market.

Shell companies are characterized by containing liquid assets such as cash, securities or other similar assets. Transactions of shell companies constitutes a severe problem since the purchaser often has the aim of obtaining undue tax advantages by not paying the tax debt of the company.Historically it has been complicated for the legislator to stop the set-up in an efficient way since the transactions as such are not illegal, instead rather commonly used for example to restructure companies or for the transfer of companies to the younger generation. The purpose of the current legislation is to prevent individuals and corporations to involve in shell company trade. Aiming for an efficient legislation, the tax rate is at a very high level.The issue with the rules is that also honest buyers are at risk of being covered. This calls for high demands in complying with the principle of legal certainty and the possibility to forecast the tax consequences.The purpose of the thesis is to identify and analyze eventual problems when applying the legislation.

There is always a need for more effective ways to store energy in order to reduce the human impact on the environment. One step on the way can be the use of flywheels as kinetic energy storage devices. Low frictional losses are essential for a flywheel to be effective. To minimize these losses active magnetic bearings (AMB) can be used to keep the shaft centered instead of the more conventional ball-bearings. AMBs use actuators and a fast control system that needs correct and noise-free measurement data of the shaft position and the current in the actuators to work properly.This thesis explains the process of constructing power electronics and a current measurement system for active magnetic bearings (AMB).

Every now and then new political ideas appear which creates debate. A current example of political debate is the one which concerns the creation of a feminist political party in Sweden -Feministiskt initiativ. Apparent in the current debate is that there are two existing conflicts of ideas present. The liberal thought of politics of ideas stands against feminism's demand for presence in the political life. And the other, the conflict which concerns the question of where a line between the public and the private spheres should be drawn.

The purpose of this master thesis is to evaluate how the current share price and market consensus affect security analysts target price and if an investor should pay any attention to it. Empirical data is primarily collected from qualitative interviews with ten security analysts but also from a quantitative e-mail survey. Our main finding is that security analysts are indeed affected by each others earnings forecasts as well as the current share price. This is not strange, it is in several aspects rational. Security analysts has often nothing to gain by standing out too much and not either by spending too much time trying to create their own opinions due to lack of time or the complexity of what is analyzed.

The aim of this thesis is to map the current internal information flow at Volvo Uddevalla, to detect obstacles in the flow and to find out how these obstacles can be avoided. The aim is also to describe how a corporation, in this particular case Volvo Uddevalla, creates knowledge and use information. The study is performed in order to create a base for the coming implementation of a new information standard. The method used is conducting an information audit investigating the current management of documentation according to the changes that have to be made to carry out the claims from the standard. The investigation is made by way of interviews with 16 of the employees at Volvo Uddevalla.