This thesis describes the redesign ofequipment designed for drying bags thatis used in Fresenius Kabis´manufacturing of their nutritionmedicine in Uppsala. The need of thistask arise during the start of thedevelopment of a new packaging line werethis equipment were meant to be used. Anevaluation of the bagdryers capacity andcapability was necessary.The work started with gathering ofinformation from suppliers of the usedcomponents and from the responsibleengineers for this equipment. Aneducation to learn how the equipmentworked and how to operate it were taken.That was followed by the creation of astudy plan were the tests were plannedto test different parameters effect onthe drying result and to see if thebagdryer managed to handle the bags ofthe correct format in the pace that theequipment should be designed for.The test results detected a need ofdesigning a unit with a function thatholds the bags in place while passingthrough the dryer in order to attainhigh quality results. The results werelater used for optimization of thedesign.

The purpose of this work is to design and construct a device able to measure the mechanical attrition of oxygen carrier particles. Those particles are used in chemical looping combustion and in the present situation there is a lack of knowledge in how the attrition process work and in which extension. To find already tested solutions trying to answering this problem a literature study wascarried out and the best solution found was the so called Grace-Davison Jet-Cup method. This method is supposed to emulate the attrition caused by a cyclone separator and its advantages are that it is possible to use small test amounts, 5-10 g, and a thirty minutes long test will be enough to acquire useable results. An device was designed based on the Jet-Cup method with some slight modifications.

AbstractThis qualitative study has been made to examine which factors that are required to create a work place that can be associated with loyal co-workers. The study covers half structured interviews with nine people on different levels and with different positions, within a manufacturing company in Värmland. Our ambition with this study is to find out if, and if so, in what way the view on loyalty and which factors that are required to encourage loyalty, differ depending on witch level one belongs to in the organization. Our thesis is that our respondents will have various ways of expressing the term loyalty, and that these various ways are linked to the different levels that each employee is currently stationed at.The result of this study shows that the way people look at loyalty, and what loyalty is really about, does not differ that much among our respondents, regardless of their level. The factors that, according to the respondents, are important if one wants to create a work place that can be associated with loyal co-workers are: to be able to feel trust towards and have faith in those one works with, as well as the company and the way things are being run, to be able to experience the feeling of community, and that one is happy with ones work place, as well as ones co-workers.

This report deals with prefabricated bathrooms and the advantage, during the production process, they have compared to ordinary produced bathrooms.The work is done together with the building company JM. The common task is to investigate if the manufactures, in spite of standardized design can meet the concept of JM, i.e. high flexibility and adjustment towards the customer. In JM they are doubtful to the method, as they did not yet worked with prefabricated modules and think that the choises for the costumer will be limited.There will be a short resume of the progress of the bathrooms and its importance as sanitary and wellbeing.The recent problems with damage caused by damp in bathrooms. Have resultade in regulations.

The thesis was performed at the lighting company Zpecta AB. Zpecta needed to develop alternative attachment of their LED-luminaire Capella. Today Capella attaches in metal ceilings with four magnets. Zpecta got indications from their customers that there was a need for other attachments. The purpose is to determine the customer?s requirements and the interfaces that are considered for Capella.During the thesis, Capella was only on the market for testing and evaluation.The thesis was initiated to create a specification.

This report was written as a result of a Bachelor Degree Project at the School of Technology and Society at University of Skövde spring 2007, together with Jede AB in Mariestad. The report covers the development of a door to a coffee vending machine that is under construction, and will in a chronological order describe the project from ideas to final product.The project started with a rather extensive feasibility study that thru market research and user tests sorted out the opinions of potential customers, concerning today?s available assortment. Technical areas concerning materials and manufacturing methods were also scrutinized for the consideration of the possibilities of a future production.The next step was to constructively generate ideas and thoughts that later on could grow to be potential solutions. After several weeks of hard work and pieces of good advice and recommendations from the assigner, four comprehensive concepts were built up.

This thesis was commissioned by Volvo Powertrain, where manufacturing and assembling of transmissions is performed, which is used in the company's trucks and buses. The thesis has consisted of a case study that intends to study the problem areas in the current proposed activities and continuous improvements in the assembly department in the Volvo Powertrain facility.In the current situation, the proposals that are submitted by the employees suggest mainly minor improvements. The proposals concern for example, labelling of materials boxes and holders for tools, which do not generate any significant profit for the company. Directors and executives want an increased amount of proposals with a more results-oriented type, in terms of reduced costs, time consumption and stops, and improved quality. The company would also deal with the problems that arise when implementing improvements in the production.

Åmotfors Bruk AB (ÅBAB) has today an inefficient production of steam for the manufacturing of paper. Unpredictable energy prices and modernisation of the current equipment has been the underlying factors to invest in a thermal power plant, mainly driven by garbage. This facility will not only use the steam for paper production, it will also generate electricity through a steam turbine. Today, when a fault on the supplying line occurs which leads to disconnection of the external grid, all the support of electricity to Åmotfors Bruk (ÅB) will disappear. This will lead to major interruptions in the paper production, which will cause severe economical losses.

By using industrialized building, pre-installed modules can be delivered to the construction site where they are easily mounted. This method has many advantages compared to on-site manufacturing, for example, the precision during the production process should be much higher than building each wall and floor on site. Furthermore, the quick erection procedure when using prefabricated elements and the possibility to use weather protection has the advantage of not being dependent on weather conditions, and many other factors.Masonite Beams AB is a Swedish company (a member of the Norwegian company, Byggma ASA) with a relatively new technology using light weight beams as bearing elements in the walls and a certain stiff board lamella slap which is mounted on the top of the floor structure creating an integrated stiff beam / board floor structure. The elements are flat which make it much easier to transport the elements from the factory to the building site where the building parts are easily mounted with special mounting stud.One of the main drawbacks of lightweight structure is the sound transmission. The main topic is low frequency annoyance, however the complex structural elements and their mutual sensitive connections other acoustical problems might appear.

The public sector is a major purchaser of goods and services. By setting requirements for environmental and social considerations in public procurement, an authority has the possibility to use consumer power to influence the actors in a market. The purpose of this paper is to investigate public procurement of textile products in a municipality, in order to gain knowledge about factors that may be important for the use of environmental and social criteria. Håkan Hydén´s (professor in sociology of law) norm model was used as the basis of the analysis, where the conduct was investigated along three dimensions of the norm ? willingness, knowledge and system conditions ? in order to identify underlying factors that can influence the process.The results ? analyzed by using interviews and documents ? show that the procurer's willingness, motivation and knowledge are important factors in this context, as well as the political priority of the municipality.

Introduction: More and more companies have realized that keeping and using the knowledge in their companies is getting more important to get or keep a competitive advantage. The companies? organizational culture and knowledge management are essential to create knowledge transfer. Also that the employees and the leaders of the company knows how knowledge- and information transfer arknkoe done best for them. That is why we chose our purpose to be:The aim is to understand the differences between managers and employees perception about knowledge- and information transfer in a manufacturing company.

AbstractThis thesis was conducted by Jenny Jansson and Maria Madsen, students at the Faculty ofTechnology and Science and the Innovation and Design Engineer programme at KarlstadUniversity, during the spring 2008. The thesis covers 22,5hp for each student. AnnaHolmquist and Chandra Ahlsell at the company FOLKFORM were the ones who requestedthe theis, their company are located at Stora Skuggan in Stockholm. Tutor for this thesis wasLennar Wihk and the examiner was Monika Jakobsson of Karlstad University.The given assignment came from FOLKFORM and the aim for the thesis was to create afurther development of two already existing lamps from an earlier collection at FOLKFORM,?Jaipur? and ?Modern Times?.

Bakgrund: Många företag går i konkurs varje år vilket är förknippade med kostnader för de enskilda intressenterna och för samhället i stort. För att kunna vidta eventuella åtgärder innan konkursen är ett faktum är det av intresse att veta om någon av de modeller som forskare tagit fram för att förutspå konkurser faktiskt fungerar.Syfte: Syftet med denna undersökning är att ta reda på om det går att applicera någon av ett urval av etablerade konkursmodeller på svenska industri- och tillverkningsföretag.Teori: Studien kommer att testa tre olika forskares modeller och metoder: Altmans, Platts och Platts samt Pompes och Bilderbeeks.Metod: I denna studie kommer enbart en deduktiv forskningsansats att användas och datainsamlingen är kvantitativ då nyckeltal hämtas från de aktuella företagens årsredovisningar. Urvalet baseras på de företag som ansökte om konkurs under år 2011 och de som representerar kontrollgruppen har slumpmässigt valts ut bland de företag inom avgränsningen som inte gått i konkurs det aktuella året.Resultat och slutsats: Altmans och Platts och Platts modeller visar sig inte vara applicerbara på svenska företag. Dock är vissa av Pompes och Bilderbeeks nyckeltal tillämpliga till att använda för konkursprognostisering för svenska företag..

Följsam tillverkning är en relativt ny tillverkningsstrategi som myntades i slutet av 1990-talet och har fram till idag fått en allt starkare plats i den akademiska världen av tillverkningsteknik. Vissa säger att strategin är nödvändig för att uppnå tillverkning i världsklass. Det finns ett antal forskningsartiklar som föreslår ett taxonomiskt ramverk, inklusive drivkrafter och förmågor, som är associerade med följsam tillverkning. Den här studien har två huvudsakliga syften. Det första syftet är att etablera en sammanställning av drivkrafter och förmågor som diskuterats i tidigare forskning.

This thesis describes the development of a tank insert for diesel cars, from idea to a prototype. The idea is to design an insert which makes it impossible to refuel petrol in a diesel car. The insert shall be installed in the existing tank opening on diesel cars. The tank insert is designed for the Swedish company SverigeGrepen AB located in Vänge, just outside Uppsala. Their main product is a pitchfork that is ergonomically designed and durable.A pre-study were performed in which information relating to fuel caps, tank openings, petrol- and diesel nozzles were collected.