The graduation essay has been carried out in co-operation with Kalmar Industries in Lidhult, Sweden. The purpose of our essay was to develop a complete construction solution on a hoist that could lift a laying wheel, lift it up and then turn it 90 degrees. After that the wheel shall be placed in a special holder.The background of the essay is a record of reports of damage wheels when they been incorrect lifted with a forklift. The hoist shall be used together with the same forklifts that manage the wheels today. Together with our instructor at Kalmar Industries we developed a requirement Specification and from that we got free hands.However this was not the main task from the beginning, then a simular hoist should be develop but used directly in the assembly workshop without using a forklift.We started to find principle solutions that later was evaluated against the requirement Specification.

This thesis presents the design and implementation of an accounting and status notification system for the LPRng print spooler. A solution using SNMP to query for needed accounting and status data is presented, a design built upon this, and an implementation produced. As the system derives from the requirements Specification, it will make no attempt to solve all printer accounting problems or to offer compatibility with all printers, database management systems or print spoolers. However, several solutions for printer accounting are discussed and the best solution derived from the requirements Specification will be chosen..

To increase the quality in their products ABB is working towards a cleared order concept. That means that all customer specified options are to be known before they start with order calculations and construction. As it is today they use paper checklists to achieve this. One order may have several reactors, and for a reactor there can be several different alternatives. For each alternative a new checklist must be filled out.As of today all reading of the customer Specification and checklist fill in with is done by hand by different persons, and sometimes the same data is read more than one time.

This report describes the process of outlining a design proposal for a resource planning tool for TV post-production. A feasibility study in form of a participant observation has been carried out on-site, which has resulted in a requirement Specification. Based on the requirement Specification, mockups have been created to illustrate the functions and features that a final planning tool should have. In addition to developing a design proposal, an evaluation of the existing resource planning tool Ganttic has been conducted. Ganttic has been reviewed based on how well it meets the list of requirements.

This report was written as a result of a Bachelor Degree Project at the School of Technology and Society at University of Skövde, first semester 2007. The assigner was Tibrokök in Tibro, Sweden. The commission was originally to design a sliding door concept for kitchen. Later it was expanded to also include bathrooms.During the feasibility study of the project Internet was used as an information source. Kitchen brochures and magazines were ordered from different companies to give inspiration and ideas.

The thesis was performed at Forsmarks Kraftgrupp AB in the department ofmechanical engineering, FTCM. Forsmark nuclear power plant has had problems with cracks in some of the controlrods which are placed in the reactor at Forsmark 3. To investigate the cause of this,material samples were taken from five of the damaged control rods. This sampling ofthe rods resulted too short rods to be transported in the shipping container to theinterim storage facility for used nuclear fuel in Oskarshamn. Control rods are crucial components in a nuclear reactor, regulating the reactoreffect by blocking or unblocking fuel rods. Control rods which have been in thereactor are always handled under water in order to protect against the radiation theyemit. The task was to design a control rod adapter that extends the control rod sotransport can be performed from Forsmark. The goal of the work was a complete setof blueprints so the control rod adapter can be manufactured and mounted on theshort control rods and then be transported to the interim storage facility. The work began with mapping of how control rods normally being handled from thereactor to the interim storage facility.

This thesis deals with the development of a Specification regarding a push-button, which will be used to control the gear-shifting function in an automobile. In addition to this the author will describe different techniques and theories that have been helpful in achieving data and results for the Specification.Kongsberg Automotive AB, is located in Mullsjö, Sweden, the company supplies parts to the automotive industry. In the research and development department, R&D, there is a group that works with development of Shift-By-Wire systems. In an automobile with a Shift-By-Wire system the communication between the gear-shifter and the gear-box occurs electronically. The mechanical link is, in most cases, taken away and replaced by the digital system.

This project aims at investigating if the use of UML as a support to small-scale development ofan embedded system is relevant. The investigation is conducted by using UML during the initialphase of the development ofTelfafill, a filling machine by the company ?Telfafill AB?. The aimof the development of Telfafill is to separate the user interface from the control unit. In additionto this main objective, Telfafill AB would like possible changes to, and additions of,functionality of the filling machine to be investigated.Within the boundaries of this project, the development of Telfafill reached a full requirementSpecification of the proposed system, and contact was made with potential external developers.No prototype construction had been started when the project ended.

In most software engineering project, users are only involved in the beginning of the project as a help to design the requirements Specification but users can be involved after this phase too, but is it effective to do so? With this report we would like to investigate how effective it is to involve users after the requirements Specification has been written and approved. To find out how effective it is to involve the users we try some fast and simple involvement techniques on a quite far gone project. These techniques include ethnographic studies, prototypes and surveys. We also interviewed a couple of people who work with usability and finally delivered a report with our results to them to find out if they found our result relevant.

A degree project has been carried out at Motion Control, Västerås. The degreeproject ?Grafisk Skärm för Inbyggda System? have developed a first prototype of anembedded system with a display, a graphical user interface with touchscreen andpossibilities to communicate with external units.The work initiated with surveys of critical components. A technical Specification forthe desired end product was developed. With the technical Specification as support,design Specifications for hardware and firmware were developed.After the Specifications were done, a circuit diagram was developed and a circuitboard was made.

Ocean Modules Sweden AB is a small business active in the field of underwater technology. Thecompany was contacted by the Swedish Defense Materiel Administration (FMV) in order todevelop a new system that would conform to their specific requirements. Two students at theRoyal Institute of Technology (KTH) were consulted in conjunction of this project in order to aidthe development and conceptual design of the system.The primary users of the system are the divers of the Explosive Ordnance Disposal division (EOD)- a branch of the Swedish Armed Forces. The purpose of the product was to incorporate allnecessary functions required by the EOD divers into one single system. The main functions arecommunication between the surface operator and diver, video recording, still imaging, positioning,navigation and ocean floor mapping with sonar.

This exam paper has been a collaboration between the writers and SYSteam Utvecklingspartner in Huskvarna. The assignment was about finding a need for a mobile application, making a requirement Specification document with design documents and parallel to this constructing a prototype. The assignment is summarized in the following questions:? How can companies in the forest industry benefit from mobile information technology?? How can a user centered perspective be used in the process of making the requirement Specification document and the design documents?? How do guidelines for usability apply to a mobile application?Three visits to companies in the forest industry were made to find a need for mobile information technology solutions. After a small analysis of the different companies? problems and conditions the decision was to use Tenhults Impregneringsverk AB in the case study.We used the FA/SIM method in our job of finding the organization needs for change and the principles of User Centered Design in the work of constructing a prototype.The result of our work is a requirement Specification with design documents and a prototype.

Purpose of the thesis is to construct a tool for car wheel change. Car wheels can be heavy and hard to handle and therefore the company Movomech intends to develop a tool that makes wheel change easier. Movomech does not have any similar product and because of this the work was condition less.The intended users of the product is tire workshops and there for the work began with investigation of these. The reason of the investigation was to see how wheel change is done and how tire workshops are planed. The tire workshops? crew?s opinions were also considered and above all one important conclusion was made.

Atlas Copco Tools develops and manufactures handheld industrial tools. Heat and surface treatments are used to provide the tools with certain properties. There are no routines for the choice of treatment or for how to specify treatment on drawings. Production documents that are sent for production abroad may not be clear enough. Some treatments are known as trademarks and there are no instructions for how to specify these on drawings and in CAD-models.The purpose of this master thesis work is to create recommendations for the procedure of choosing heat and surface treatment.

This thesis describes a further development of an existing prototype named Automatic pin bone remover. The further development was requested from the Swedish consulting firm ATM AB. The request of automatic pin bone removers is high and has the potential to be a worldwide leading product.The goal with the thesis work is to further develop an existing prototype. In order to achieve the goal a pre-study of the prototype had to be made in order to define a customer demand Specification. The thesis work is then continued by a function analysis which differs from a conservative one.