The challenges facing low voltage grids are rising as an increasing number of domestic houses transition from fossil fueled heating to electricity based heating. Several environmental goals and visions have the same transition from fossil based power to electricity based power in mind for the transportation sector. One of the most important tools for this transformation is widely regarded to be the electric vehicle. With the demands of the electric vehicle pressuring the power grid, several questions arise regarding the growth of the electric vehicle market and what repercussions it may have on the grid. This paper focuses on a typical low voltage grid in southern Sweden and what effects a growing electric vehicle market may have on it. Through computer-assisted simulations based on several future scenarios regarding the EV market, this paper finds that few modifications and reinforcements are needed on this particular grid within the next 10 to 15 years.

An important process for grid companies in order to reduce power losses in electricity distribution grids is to figure out where and how they appear. This report describes the factors that cause power losses in low voltage distribution grids and methods for how they could be measured and analyzed. Measurement data for consumed and injected energy were collected for twelve low voltage distribution grids owned by Gävle Energi AB in order to analyze the size of the power losses and how the measurement uncertainty affects the collected data. Then models of three of the grids were created in MATLAB in order to analyze the data and the power losses were calculated to be compared to the collected data. Curve fitting were also used as a method in order to analyze the power losses from collected data.The results show that the losses in the studied grids are low.

Historically transformers with system earth equipment have been modeled as open circuits in zero sequence. This approximation has been satisfying, but lately it has been discovered that equipment on one side of the transformer have responded to faults that occurred at the other side. Most of these problems took place when the majority of the system on the secondary side of the transformer contained cables. These findings have led to questioning whether or not the former model of the transformer in zero sequence is correct. This report investigates if it is necessary to represent the transformer in zero sequence in another way than it is usually done today.

This master thesis describes the development of an UPS module. UPS is an acronym for Uninterruptable Power Supply. The UPS module has been developed at the company AerotechTelub AB. The UPS module delivers the necessary voltage and current in case of a power interrupt. If a power interrupt occur, the computer system has one to three minutes available to store data and shut down correctly.

The aims of the following project has beento make a proposition how to create aspecific kind of transformer. Thefollowing report evaluates the differentimportant variables and contains asuggestion for a possible design. Intheory it's an ordinary transformer that'ssuppose to transform electrical effect toa high voltage line. The design of thetransformer is using an already existingcurrent transformer design and is adjustedto work for it's specific purpose. Theproject also contains the developing of atransformer simulation model that will beused to evaluate and optimize thedimensions of the resulting transformer..

The interest in small-scale electricity in Sweden has increased strongly in recent years. The interest is noticeable both among politicians to increase the share of renewables in the energy mix, and among electricity consumers to partially replace purchased electricity with self-produced. This has resulted in a significant increase of electricity production in low voltage grids in recent years, and the trend appears to continue in the coming years. The majority of the new production plants are solar cells, followed by wind turbines, and it is also in these the greatest efforts are made in this paper.Distributed generation is often seen as something positive since it will contribute to reduced transmission losses and reduced voltage drop in the networks, and that it increases the share of electricity from renewable sources. In cases where the grids are not strong enough, or in other ways not adapted to manage the installed production, power quality may be adversely affected.

The aims of the following project has beento make a proposition how to create aspecific kind of transformer. Thefollowing report evaluates the differentimportant variables and contains asuggestion for a possible design. Intheory it's an ordinary transformer that'ssuppose to transform electrical effect toa high voltage line. The design of thetransformer is using an already existingcurrent transformer design and is adjustedto work for it's specific purpose. Theproject also contains the developing of atransformer simulation model that will beused to evaluate and optimize thedimensions of the resulting transformer..

The interest in small-scale electricity in Sweden has increased strongly in recent years. The interest is noticeable both among politicians to increase the share of renewables in the energy mix, and among electricity consumers to partially replace purchased electricity with self-produced. This has resulted in a significant increase of electricity production in low voltage grids in recent years, and the trend appears to continue in the coming years. The majority of the new production plants are solar cells, followed by wind turbines, and it is also in these the greatest efforts are made in this paper.Distributed generation is often seen as something positive since it will contribute to reduced transmission losses and reduced voltage drop in the networks, and that it increases the share of electricity from renewable sources. In cases where the grids are not strong enough, or in other ways not adapted to manage the installed production, power quality may be adversely affected.

The use of silicon carbide (SiC) as a base material in power electronics has manyadvantages, including high breakdown voltage and excellent temperature endurance.However, the packaging of such electronics presents major challenges and there is aneed for packaging that can operate in higher temperature. The purpose of this thesishas been to develop a test method and verify the functionality of SiC powertransistors prototypes with a new packaging technique developed by Swerea IVF AB.It includes setting up an electrical test-bed for power and high temperature cyclingand analysis of the results. Even though test confirmed functionality after thepackaging process, (at room temperature) the performance seemed to have been reduced. This could be a result of the measurement setup and the packaging process.In higher temperature the transistors failed to operate longer than a couple ofminutes which showed the weaknesses in the design and the challenges with this typeof packaging..

The dependency of continuous electricity supply is high in the Swedish society today, at the same time no one is willing to pay for a too costly or over dimensioned power distribution system. The owners of the distribution systems are the ones responsible for this balance act of maintaining a high quality of electricity delivery to customers at a reasonable cost.In this master thesis a limited part of the primary distribution system (10 kV), owned by Mälarenergi Elnät AB and located in the city centre of Västerås, was chosen for a deeper analysis of its reliability. Its ability to handle outages of system components (N-1 and N-2 contingency analysis) was investigated to find out potential weak spots and parts of the grid that showed signs of being overdimensioned.The results of the performed simulations showed that in 74 % of the studied N-1 contingencies cases, consisting of outages of a bus bar in a distribution substation, the system could handle this without causing outages in other parts of the grid. For the N-2 contingencies 61 % passed the test. It was also found that one of the two included high voltage substations could alone supply the investigated part of the grid.

Sweden will, in accordance with the EU-directive 2003/54/EC, move from post-regulating the electricity power grid-tariffs by using a fictitious grid, to a regulation in advance which uses the actual power grid as a starting point. For this purpose a component breakdown of the grid needs to be made to determine the value of the network and by that the tariff price that is reasonable for the network business in question to charge.The primary breakdown criteria is the voltage-level and type of region. Voltage-level is crucial for the cost and complexity of a grid-part, because the higher the voltagelevel is, there are more and stricter laws and rules to follow. This work is limited to the distributionpart of the grid, in other words voltage levels from 20 kV and below.The type of region is crucial to the type of components you can and want to use. In city environments both overhead-wires and independent substations are undesirable for both practical, safety and aesthetic reasons.

This thesis concerns how the power quality in the grid is affected by the connection of wind power plants. As things are at present, Fortum Distribution AB has a number of wind turbines and wind parks connected to the own grid. As the pressure on building and connecting additional wind power is increasing, so is also the interest of how the already existing wind power generation affects the power quality in the nearby distribution grids. The study is performed by direction of Fortum Distribution AB and is limited to the 10 kV/40 kV-grid in Bohuslän, Sweden. The methods for calculation of power quality are compared to the results of a number of measurements.

Detta arbete behandlar mätmetoder för detektering av partiella urladdningar (kallad PD från engelska benämningen Partial Disharge) i HVAC- och HVDC- högspänningskablar. HVAC står för ?High Voltage Alternative Current? och HVDC står för ?High Voltage Direct Current?. När en viss hög spänningsnivå överskrids i kabeln uppstår olika typer av partiella urladdningar och dessa skadar kabelns isoleringsmaterial. PD- intensiteten ökar med tiden och om de tillåts fortlöpa under en längre tid kan de med tiden helt bryta ned isoleringsmaterialet vilket leder till ett fel.

When cylinders for motor saws are manufactured there are high demands on the cylinders strength and wearing qualities. Aluminum is a material with low density and is used by Husqvarna AB for their motor saw cylinders. The aluminum is strengthening with nickel that is attached to the cylinders through electrolysis. When aluminum is in contact with oxygen a film of oxide is formed. To eliminate the oxide and to prevent formation of new oxide zinc is used.

This master thesis has been performed at Solvina in Gothenburg for Skellefteå Kraftand Vattenfall Eldistribution. The aim of it is to investigate the consequences of theinstallation of a wind power plant on the mountain Uljabuouda in the vicinity ofArjeplog. Especially the impacts on voltage and transient stability are examined.Furthermore, the amount of extra strain on the voltage regulation equipment and theneeds for increased regulation capabilities are looked into.The wind power plant is planned to be built by Skellefteå Kraft and connected to a130 kV grid owned by Vattenfall Eldistribution. The work comprehends the followingmain parts:- Theoretical studies aimed at wind turbines and power system stability issues.- Modelling of the type of wind turbines assumed to be built on Uljabuouda.- Simulations of different operation cases and analysis of the simulation results.The results from the simulations show that, as far as voltage stability and extraworkload on tap-changers are concerned, the wind power plant does not, in anysignificant manner, worsen the present conditions. The problem of overloading theline between Arvidsjaur and Vargfors is also minor.