This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

The Main problem: How small-sized manufacturing companies can create and sustain a stable position in the industry, which leads to profitability.Purpose: The purpose with this essay is to compare two small-sized manufacturing companies, Datek Industrielektronik AB and AB Micatrone to study which strategical resources each company possesses. At the same time analyse if the strategical resources are to be consider as sustainable competitive advantage.Method: A case study has been implemented in two small-sized manufacturing companies. The collected primary data derives from semi-structured interviews.Theoretical framework: The theoretical framework is based on The Resource-based view where the independent variables are the VRIO-model, resource tree and external resources. The dependable variable is sustainable competitive advantage.Empirical foundation: The empirical foundation is based on the compilation of the few conducted interviews with Datek and Micatrone.Results & Conclusion: Datek and Micatrone show both similarities and differences in what creates their sustainable competitive advantage. The management of both companies creates according to the VRIO-model sustainable competitive advantage.

This project is about investigation and improvement of a V-plow for the company Swekip. A V- plow is used for snow removal but this product has been found to have deficiencies in its construction, breaking down and not living up to the desired objectives. This is because the product is ordered from a company in China where they have some problems with understanding the purpose of the plow.Initially the existing plow is investigated, all the shortcomings set out and examined, what is wrong and what needs improvement?When the solutions were done they were evaluated and examined that they actually live up to the desired requirements.This assignment is a pure construction project where the majority is implemented in CAD, where models are developed and FE analyses are carried out. But the project also includes a feasibility study, idea study and hydraulic design.The results are presented in the form of a CAD model and associated drawings that will serve as the manufacturing basis for the new V-plow.

This study aims to investigate how small scale manufacturing companies reason around an implementation of a PLM-system, as well as the suitability of these systems compared to larger companies. The study is built on a qualitative method. Initially, secondary data was gathered through books, articles and reports. Primary data was gathered through four interviews. Two interviews were performed with PLM resellers, one interview was performed with a PLM developer, and one interview was performed with a small scale manufacturing company that opted to not implement a PLM-system.The results imply that overall differences between larger and smaller companies exist in regard to the need of PLM systems.

Shareholder, who decides to continue with the company, can cause that they become per-sonally liable for its upcoming obligations. Creditors must lodge an appeal against the shareholder to get compensation for the harm they have suffered. The damage rules in Swedish company law are designed to utilize the company?s interest, that is, shareholders and other corporate members shall promote the interests of the company and not cause damage.The rules about compensation that shareholder obligates itself to are difficult to apply and are adapt to the specific cases. For a shareholder to be personally responsible in a real situation a company has to establish a subsidiary company, which is being driven undercapitalized, intended to benefit the shareholder.

The Swedish automotive industry has since way back been struggling with bankruptcy, abroad buy outs and staff cuts. Competition and pressure on prices are two factors that affect the automotive industry. Because of this, the companies are pressured to continuously developing their work in addition to be able to compete on the market. The aircraft industry has successfully managed to implement additive manufacturing (AM) and for motorsport has several components manufactured with AM been used. When AM is used as a manufacturing method, there are a number of advantagesthat follows.

The world gets smaller and smaller and goods, services, people and information are nowadays more and more able to freely cross borders. Half of the Swedish GNP consists of export and almost 70 % of that amount is goods. Because of today?s increasing globalization the Swedish companies are now faced with both new opportunities and threats. Companies with goods which are manufactured in Sweden gets challenged by increased competition from cheap goods produced in other countries and companies can no longer afford to entirely focus on the domestic market.

This report is about helping Q-Med AB in Uppsala to start its implementation of uncertainty of measurements analyses in their manufacturing department. Prior to this, the company relied solely on personal experience or did not take this uncertainty into consideration at all during different kind of measurements, which means that some of the processes that the company previously believed were within specified acceptance limits, will actually fail when considering these sources of uncertainties.Q-Med AB needed some sort of instruction to help the company, in a systematic way, to investigate different types of disorders that are affecting all kinds of measurements. This instruction includes a short summary about measurements and uncertainty of measurements in general and a detailed procedure about how these uncertainties are going to be handled in their daily work.The goal was to be able to use this instruction to systematically locate, eliminate (when possible) and analyze all kinds of disorders when measuring. Q-Med is using a lot of different types of instruments when measuring different types of quantities, including temperature, mass, pressure and density. This instruction will hereafter be used for every instrument, regardless of quantity and type of instrument.The instruction is tested through 4 different kinds of measurements, for mass, temperature and humidity.

The female labour is still a rather unexploited resource in many parts of the world. Unleashing women?s potential, giving them the possibility to start their own enterprises would increase the economic growth. Not only does women's entrepreneurship foster greater equality in the world but it also creates a more versatile economy. Sweden is considered to be one of the most equal countries in the world; still, entrepreneurship is an area with sharp gender differences, especially in some industries.

This Master Thesis is a product development project that has been carried out in cooperation withSvea Teknik AB. The company has developed an apparatus for attachment of a keel to a hull base ofa boat. The purpose for this thesis has been to compare a new concept of keel attachment incomposite material to thetraditionaldesign solution. This new keel attachment minimizes thedamages that may arise on the keel and the hull of the boat in shape of stresses impacts at grounding.Today it is a problem, relating to keel attachment on sailing boats having a fin keel or a bulbous keel.The manufacture focus on developing larger draught and shorter keel blades. The overall purpose isto increase performance of the sailing boat.The task for this thesis was to develop a concept of keel blade in composite material and investigateattachment to a sheet-shaped element.

Upon marketing the system in Europe and the USA cost savings generated from reduced work force have been prevailing. Since the cost of labour is much lower in the Asia Pacific region other factors have to be stressed. The parameters of flexibility and quality assurance may however cover any initial investment in a production system. Our purpose is to value flexibility and quality in a manufacturing context, applied to DAS, in order to use it in investment calculations. In order to make an adequate estimation of different companies, due to problems associated with acquiring correct figures, the Key Success Factors needs to be examined so that the gathering of numbers can be conducted with more focus.

Titel: Innovate or Stagnate! ? Open innovation in manufacturing small and medium-sized businesses in Småland.The purpose of the study is that, from a leadership perspective (innovationmanagement), create a better understanding of open innovation in manufacturing small and medium-sized enterprises. The study therefore intends to contribute to the understanding of how open innovation processes leads to greater innovation in manufacturing small and medium sized businesses.We have used a qualitative research method and adopted an abductiveapproach. We made interpretations and created meaning based on our research results.Our theoretical framework is based primarily on Chesbroughs (2003) research on open innovation. Based on this model, we have selected a number of other theories, which we perceived as prerequisites for small andmedium sized companies in open innovation processes.

The working capital describes the short-term financial position and focus on cash flow and the actual inflow and outflow of money in the company. Working capital is part of the company's financing and consists of the company's current assets and current liabilities. There are resources that are used in the daily activity and can be optimized. The more effective they are in circulation, the higher value they create. The control of working capital is called Working Capital Management and has its basis in the company?s Working Capital Policy.

This report is about helping Q-Med AB in Uppsala to start its implementation of uncertainty of measurements analyses in their manufacturing department. Prior to this, the company relied solely on personal experience or did not take this uncertainty into consideration at all during different kind of measurements, which means that some of the processes that the company previously believed were within specified acceptance limits, will actually fail when considering these sources of uncertainties.Q-Med AB needed some sort of instruction to help the company, in a systematic way, to investigate different types of disorders that are affecting all kinds of measurements. This instruction includes a short summary about measurements and uncertainty of measurements in general and a detailed procedure about how these uncertainties are going to be handled in their daily work.The goal was to be able to use this instruction to systematically locate, eliminate (when possible) and analyze all kinds of disorders when measuring. Q-Med is using a lot of different types of instruments when measuring different types of quantities, including temperature, mass, pressure and density. This instruction will hereafter be used for every instrument, regardless of quantity and type of instrument.The instruction is tested through 4 different kinds of measurements, for mass, temperature and humidity.

Nowdays an efficient production is critical to achieve for companies competing on the market for steel cutting tools. One of such companies is Halmstad based Tooling Support Halmstad AB that manufactures threading-taps, threading-dies and parting off tools, towards a centralized warehouse in Schiedam, Holland. The large amount of different products, approximately 2500 is a big contributor to the problem along with a new order system that creates a demand of low setup times. Previously the company was forwarded orders through quarter based prognoses which enabled planning of the production over a longer time span. Currently the newer order system ZENIT is in use and the company thereby gets their orders weekly.