The purpose of this thesis is to investigate the possibility to make small, cheap and ultra low power sensor platforms, connected in wireless networks for monitoring of home and industrial environments. The concept is based on ideas from our supervisor, Jerry Lindblom. The developed system consists of a generic platform for different sensors, a receiver and software. A GPRS module from RO Rollytech AB and a database from Gema Industri AB have been modified and used to demonstrate an example of a complete system. To the platform, it is possible to connect any resistive sensor and any sensor that can act as a switch.

The aim and research questions of this study are concerned about how, and what kind of, problems and subjects that citizens raise during verbal interaction with politicians and officials in the field of participatory democracy. The theoretical framework of the study dominates by theories with a positive approach towards participatory democracy, but there is also a broader discussion on the phenomenon?s strengths and weaknesses.The case in focus of the study is a specific phenomenon of participatory democracy created by the municipality of Växjö. The empirical material that is analysed is consisted of written text based on the verbal interaction from these meetings between citizens and politicians/officials.The outcome of the study shows that most of the verbal interaction was held between citizens and politicians/officials in a vertical direction and that a major part of the responsibility concerning the raised subjects is estimated to be in the hands of the latter part. In the light of under what circumstances the meetings are practised, the democratic and collective minded performance of the citizens is argued to be in good condition, despite the dominating vertical interaction and estimation of trust..

This report describes a project carried out in cooperation with Klippan Safety AB. The purpose of this project has been to develop a product that facilitates the living area in a truck cabin for the customers. To be able to develop, in a structured way, that kind of product, the project has been based on different product development theories. The project contained of following parts: marketing research, product generation, product evaluation and prototyping. After information from the marketing research and discussions with the company, the decision was made that the task was going to consist an improvement of the existing product referred to as 'the comfort module'.

Vertical jumping ability is an essential skill in many sports. The aim of this study wasto investigate the acute effects of assisted jumps on subsequent countermovementjump (CMJ) performance by female athletes. Nine healthy, trained female subjectsvolunteered to participate in the study. In a randomized order, they performed oneregular warm up protocol before testing their CMJ baseline value, and one warm upprotocol with an addition of five assisted jumps at 30% body weight reduction beforeanother CMJ test. Elastic cords attached to an overhead pulley system and to aharness around the subjects' upper body were used to reduce the body weight.Significant improvements were noted in jump height, 2.3 cm (7%), positive forceimpulse, 4.7 Ns (2%), vertical take off velocity, 0.1 m/s (3%), countermovement time,0.1 s (12%) and breaking time, 0.1 s (14%), p.

The river Göta Älv reaches between Vänern and Gothenburg and is the main raw water source for Gothenburg that supplies about 700 000 people with water. To protect and maintain a high water quality, continuously samples and water analyses are made throughout the river. In 1998 a protection area was founded between surte and Lärjeholm where the raw water intake is. This was made to increase the awareness of the importance to protect the water. However, there is a lot of contribution of untreated stormwater to Göta Älv within the protection area.Göteborg Water and Sewage Works commissioned this thesis where two areas, Tagene industrial area and Kärra residential area, with untreated stormwater outlets within the protection area are studied.

Problem discussion: How should information be handled to facilitate and benefit from modularity? How should Clarkson Inc. adapt their information handling to modularity and what benefits can be reaped by doing this? Purpose: The purpose of this master thesis is to help Clarkson Inc. adapt their information handling to modularity and to extract theories, methods and tools to guide companies in similar situations.

Over an extended period of time there have been plans to establish a shared facility in Lennheden to extract groundwater from the Badelunda esker to provide drinking water for the cities of Borlänge and Falun. The city of Falun is dissatisfied with the quality of its drinking water and the city of Borlänge is concerned about the risk of contamination of its existing groundwater supply at its current location. To provide a basis for a decision on this issue, the company Midvatten AB has been commissioned to perform hydrogeological investigations in the area of Lennheden.The purpose of this thesis is to design a functional groundwater model of the area between Lennheden, place of planned extraction, and Övre Tjärna, place of existing extraction, to get a better understanding of the groundwater situation in the area. A groundwater model enables simulations of different scenarios in risk assessment and contaminant transport. The aim of the thesis is that the model can be used as an aid in Midvatten?s investigations in Lennheden and that it also can be used in future projects in the area.The model has been made in Processing Modflow 5.3 and encompasses an area of 19,5 × 11 km along the Badelunda esker and the river Dalälven between Djurmo and Frostbrunnsdalen.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

One of the most distinguishing features of contemporary globalisation is production fragmentation, a splitting up of the manufacturing of a good into several different stages. Production fragmentation creates new opportunities through vertical specialization; a country incapable of mastering the entire production process may specialize in the manufacturing of one separate part. The aim of this thesis is to examine to what extent international integration affects a country?s ability to engage in vertical specialization in an industry characterized by production fragmentation. The analysis focuses on the european integration process over the last decade, where countries in eastern Europe with relatively low labour costs have been integrated with more capital abundant western economies.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

Within today?s organizations there is continual development work to increase efficiency and the power to compete at the market. Production development with focus on continual improvements constitutes an important part of the daily work within a lot of organizations today.The purpose of this study is to contribute to a part of the development process that Volvo Penta factory in Vara has in mind. A description of the current situation was compiled by mapping the internal runnings and material flow throughout the factory. A new suggestion for a layout and a comparison with the current situation will assist with creating a factual basis for the development of a new goods reception.A study was made where the volumes and the quantity of the daily arrival goods were settled.

This master thesis has been carried out as a prototype development project. The project hasbeen performed in cooperation with ÅF Combra AB. The purpose with the master thesis is toconstruct a Bluetooth interface between an accelerometer and a smartphone and constructinga physical prototype containing an accelerometer. This is done to test a new user interface tomobile phones. The master thesis has also included a research about the possibility toimplement distance measuring with Bluetooth.

The high level of energy consumption that the industrialised countries have reached and thepollution that this brings has long been a cause for analysis and debate, development and usageof so called renewable energy sources is therefore more important than ever. The energy in theelectromagnetic radiation from the sun is an interesting alternative. One way of harvesting thisenergy is by using solar cells, devices that generate DC current when exposed to electromagneticradiation.The goal of this master?s thesis was to design a solar powered power supply to Syntronic AB?sMidrange platform. The envisioned application is a stand-alone distributed embedded system,for example a node-based temperature monitoring system.

The purpose of this thesis is to examine and analyse which effects a service strategy has on the control system of an organisation. The thesis takes a service perspective, and it is assumed that a service strategy gains competitive advantage and that the goal of the service strategy is to increase the customers? satisfaction level. A qualitative in-depth case study was performed on a Swedish beauty company. The organisation?s vertical structure was examined, from central to local level.

Self-compacting concrete has soon been around for a decade. Recently the prefabrication industry has started to use this fairly new concrete type in larger scales, mainly because of its distinctive properties.  There are still certain areas that need to be thoroughly examined, such as bond capacity. There have been very few studies regarding shear capacity due to the fact that the procedure is complicated.This report will highlight a method to examine the shear capacity of different surfaces that have been prewetted as well as non-prewetted surfaces. The surface areas follow BBK 04?s and Eurocode 2?s demand for surface roughness.  A smooth surface will be completed in order to confirm if the different shapes influence the bond strength by shear stress or not.                       The purpose of this essay is to measure the bond strength within the shear capacity as well as examine the impact it has on surface roughness and treatment for shear bond.The method used to identify the shear capacity is called L-shaped Push-Off Test.