The purpose of the study is to investigate the possible effects of an unstable ventilation system and its influence on energy use and thermal comfort. The report also explores how qualified personal working with HVAC view and handles system control.In order to meet the requirements in energy efficiency and a comfortable indoor climate control regulation is a prerequisite. With optimized increased complexity of the climate systems, it becomes more challenging to control the system and the risk of unstable control increases. No previous studies about what affect an unstable system can have on energy use and thermal comfort have been found.The report is based on several tests were the controlling variable has been increased until the system becomes unstable. Two different types of unstable systems have been investigated.

Glass has sophisticated front properties and are used as facades in high buildings. During cold periods, these glass facades could cause thermal discomfort, due to cold downdraught. Cold downdraught can be countered by placing heaters under glass surfaces. Nowadays technology offers highly insulating windows, which is why there is an interest to investigate the indoor climate with only underfloor heating. The research in this area is limited, and few empirical methods are available.

The E-department at GETRAG All Wheel Drive in Köping have problems with the efficiency on parts of their production equipment. The equipment with the most significant efficiency problems are four automated multifunctional production cells that produces housing for rear drive units. The major part of the problem is the large amount of small stops that causes the low efficiency.The department already worked with logging of interruptions and efficiency calculations before this project started. However this work was not done to the extent considered necessary for a systematic follow-up of the interruptions.The aim of this paper is to point out a more effective and systematic way to work with logging of interruptions and the follow-up. In addition the equipment were studied with a method for efficiency calculation that ? if used properly- is a more powerful and a visually better method than the one used by the company today.As the initial current state analysis of the equipment was made a lack of documented knowledge about the equipment was discovered.

Compressed air is an energy source that is widely used in today's trucks and buses.Compressor located next to the engine supplies the pneumatic system with the compressed air and is lubricated with the engine oil. Some of the oil follows the air flow in both liquid and solid phase. The solid phase, namely the carbon particles are created due to the high temperature in the compression chamber.Oil- and particles carryover softens and destroys the rubber material in the air valves and disturbs the mechanical function of various components in the pneumatic system. In order to reduce oil- and particles carryover is an Air Processing System (APS) set downstream the compressor.No method for establishment of oil- and particles carryover from the compressor exists at the moment. Therefore the filtration efficiency of APS is currently unknown.

Title: Audit teams ? what affects the efficiency?Authors: Petter Johansson and David RubinSupervisor: Andreas JanssonCourse: Dissertation Accounting, 4FE03E, 30 ECTS, Spring 2011.Key Words: Audit team, Efficiency, Team WorkBackground and problem: Theory and literature in the field of audit teams?efficiency are limited. The theory and literature that existed was not conducted inSwedish context. It was identified that no one had examined the factors thatinfluence the efficiency of the Swedish audit team's. Efficiency affects howresource-and cost-effective an auditing firm can be while the audit is performedwith quality and therefore it is of interest to be examined.Purpose: The purpose of this thesis is to explore and explain what may affectSwedish audit teams? efficiency during the work processMethod: The thesis has been based on existing theory and literature to explainwhat affects audit teams? effectiveness.

Poly- and perfluoroalkyl substances (PFASs) are a group of environmental contaminants that have gained increasing attention due to their potential to bioaccumulate, environmental persistence and potential toxicity. PFASs have been found in surface water, sediment, air, soil, sludge and ice caps globally, as well as in wildlife and humans. Furthermore, PFASs have also been detected in drinking water, leading to raised concerns for human health, since drinking water is one of the most significant sources of PFASs for the general population. Conventional water treatment techniques have shown to be ineffective removing PFASs, highlighting the importance for further research to develop efficient removal techniques. The aim of this study was to investigate the removal efficiency of PFASs in water using two treatment techniques; granular activated carbon (GAC), type Filtrasorb 400®, and anion exchange (AE), type Purolite A-600. Additionally, the effect of dissolved organic carbon (DOC) on removal efficiency was studied.

The master thesis, conducted at Metrima AB, concerns the development of a non-intrusivedistribution meter as a basis for individual tap water billing in apartments.The project is conducted in response to the market interest in individual tap water billing inapartments as an answer to environmental concerns regarding water consumption. Due to thehigh installation cost of traditional water meters, a new method of determining waterconsumption, without having to cut water pipes, is proposed.The proposed method distributes the total water consumption for an apartment complex toindividual apartments according to distribution meters, measuring water run-time, in eachapartment. The water run-time is estimated by measuring the water pipe?s outward vibrationsand temperature changes.A test environment was established and a prototype built, using a tilt- and vibration sensor forvibration sensing and a precision temperature sensor to measure temperature changes. As bothsensors work well in the test environment, further testing was done in 3 apartments for aduration of 5 days.

Lower energy use in buildings is a result of increasingly stringent energy requirements across Europe. When conventional district heating technology is used in areas with low energy consumption heatlosses do not fall even though the amount of energy delivered is reduced. This reduces income for thedistrict heating company. To maintain their economic viability the district heating companies? majorchallenge is to implement new solutions that minimize heat loss.

Due to human influences on the climate an increase in Earth's mean temperature is today an accepted conception. With a rising temperature discussions have started how the climate in an area will change in the future. Equally interesting and important is it also to study the precipitation in an area. Precipitation is the factor, next to temperature, that affects most how a climate in an area looks like and feels. Since precipitation is connected to evaporation the latter parameter is also of interest to study.

Uvån Hagfors Teknologi AB (UHT) has developed a process ? GRANSHOT® ? for quicksolidification of metals in water baths. In the process liquid metal is splintered ? granulated ?into small drops. The drops are rapidly cooled in a water bath where all the heat energy from theliquid metal is transferred into the water.

Increased understanding of the mechanisms that operate in conjunction with the welding of metal surfaces may help to improve existing manufacturing processes, and to enable new products and combinations of materials. The purpose of the project has therefore been to acquire a deeper understanding of what is happening in the bond for steel and for the factors that form the basis for a bond to develop between metals in the production of laminates by pressing. The merge has been done by pressing and the surfaces after the experiments have been studied in detail in the scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and with interferenceprofilometry in Wyko, to provide a greater understanding of the mechanisms that influence the bonding in the interface between metals. The project was limited to contain the materials Docol 1000, HyTens 1200, Aluminum AA3003 and a commercial steel. The parameters varied in the experiments to study their influence closer are temperature, pressure, heat treatment and pretreatment. This has been implemented by pressing with varying temperature and pressure.

Swedish healthcare is in continuous need of cost savings and efficiency improvements in order to meet the increased demand for care. The theories of lean, developed from the industry, are applied more frequently on healthcare systems to increase effectiveness and reduce waiting times in patient processes. However, some processes seem to be more successful in their lean implementation than others. In this thesis, factors influencing flow efficiency in lean healthcare are examined. Through interviews with the top executive board at Capio St Göran's hospital, data is collected in order to analyze reasons for success.

The aim of this thesis is to improve the control of urea injection at the combined power and heating plant Framtidens Gärstad (FTG). Tekniska Verken i Linköping AB is the owner of the plant.The FTG plant consists of a boiler where garbage combustion is done. From the combustion nitrogen oxides are emitted. These nitrogen oxides are hazardous to the environment. To reduce the nitrogen oxides, injection of urea into the boiler is used.

The Earths climate is changing at a higher rate, i.e between 1861 and 1994 the annual mean temperature in Scandinavia increased with 0,68º C and according to recent climate models the annual mean temperature is likely to rise with another 3º C during this century.A warmer climate in many ways is associated with changing conditions for lake ecosystems. An expected higher water temperature and a stronger summer stratification of the water column increases the risk of anoxic conditions at the lake bottom. Thus anoxic conditions are likely to cause a phosphate leakage from the sediment, i.e. a higher internal loading of phosphate.In this project, the extremely warm summer of 2002 has been used as an example for a possible scenario for a future climate. By comparing levels of phosphorus in the summer of 2002 with a ten-year median value, a phosphorus related sensitivity to climate change has been analyzed for 55 Swedish lakes.

The main focus of the essay is to investigate if bugging can be justified from two ethics perspectives, the teleological and the deontology. I?ve chosen to emanate from two specific values which I believe is especially relevant to the ethical problems of bugging, efficiency in fighting crime and the personal integrity. To be able to illustrate this conflict between different values did I do an analysis of an official report which had the task to explore if Sweden should introduce bugging as a new means of compulsion. The official report's statement was that the police should have modern instrument to fighting crimes efficient, including bugging.My examination of the report showed that they used several arguments derived from both the efficiency in fighting crime perspective and the personal integrity perspective.