Möjliggörandet av molntjänster har bidragit till att Software as a Service (SaaS) blivit allt mer aktuellt. Detta är inte någon ny teknik, utan den har funnits en längre tid men har nu kommit att aktualiseras genom olika tekniska framsteg. I och med detta har företag börjat intressera sig för denna teknik som ett alternativ till egen lokal drift av IT-system. Vår studie behandlar faktorer i form av risker och drivkrafter som företag ser vid valet att använda tjänster genom SaaS. Dessa faktorer har vi funnit genom relaterad litteratur och andra studier inom området.

In this work, a method was developed and evaluated for calculating the life of welds under the influence of fatigue loads from a vibration environment. Typically, a shaker table is used for testing a component against vibration loads. The shaker table creates a vibration environment that is defined in the frequency domain by a power spectrum.Similarly, a virtual vibration table can be used to calculate the same type of load environment, which can then be used to calculate the expected lifetime. The benefit of this method is that it can be used in design, as well as in simulation of tests before physical verification tests are carried out.Today there are methods for calculating fatigue life of non-welded base material, but since many components contain welded joints, there is a need to apply this method to those types as well. To achieve this, the thesis combines two different areas, which together provide a method for fatigue assessment of welds using a virtual shaker table.The methodology is carried out by modeling the component, and its welded joints, in a finite element program.

Alfa Laval?s strategy is to focus on modularized product platforms. Several benefits areforeseen, reduced lead-time, less costs, shorter Time To Market and better quality.Development and verifying will be carried out on block level. Today the separators arebeing tested as a complete unit. A number of factors affect the test results and problemsthat are encountered can be hard to identify.

This project report shows the work around a mockup to a three-dimensional avatar-making application. An avatar-making application is a computer-based software program in which it is possible to create your own personal virtual character. The possibility to use three-dimensional avatars can in the future be essential for adding extra personal information or characteristics to social communication over the internet or over mobile phones. The problem of transforming a physical form and reconstruct it to a virtual basis has been an important problem to solve for many companies and software developers in the, for instance, virtual worlds area. Methods and ideas over making this transformation is the key throughout this project.

Three-dimensional computer graphics enjoys a wide range of applications of which games and movies are only few examples. By incorporating three-dimensional computer graphics in to a simulator the simulator is able to provide the operator with visual feedback during a simulation. Simulators come in many different flavors where flight and radar simulators are two types in which three-dimensional rendering of large terrains constitutes a central component.Ericsson Microwave Systems (EMW) in Skövde is searching for an algorithm that (a) can handle terrain data that is larger than physical memory and (b) has an adjustable error metric that can be used to reduce terrain detail level if an increase in load on other critical parts of the system is observed. The aim of this paper is to identify and evaluate existing algorithms for terrain rendering in order to find those that meet EMW: s requirements. The objectives are to (i) perform a literature survey over existing algorithms, (ii) implement these algorithms and (iii) develop a test environment in which these algorithms can be evaluated form a performance perspective.The literature survey revealed that the algorithm developed by Lindstrom and Pascucci (2001) is the only algorithm of those examined that succeeded to fulfill the requirements without modifications or extra software.

Heat and power stations are often in need of optimizations. A simulation model is a tool for findingways to optimize the plant. The scope of this diploma work is to develop a simulation model ofBoiler 5 at Mälarenergi AB. Boiler 5 is a circulated fluidized bed boiler that was taken into service inyear 2001. Among the included parts in the boiler are cyclone, convection part andINTREX-chambers.

During the last decade a new technique in animal breeding has developed called genomic selection. It is based on estimations of the effect from genetic markers on traits that are calculated in a reference population. By genotyping individuals, genomic breeding values can then be estimated without phenotypic observations. The aim of this essay is to investigate the response of genomic selection on breeding schemes for dairy cattle. The accuracy of the genomic breeding values is affected by the proportion of observations included in the validation set and how often the equation for estimating breeding values is reevaluated.

The objective of the thesis is primarily to conform and encode a digital signal to be controlled by software. The idea is to transport today?s tracesignal through the IP-network instead of cable-net. In this report I will suggest a possible solution to get a fully passed result with no peculiar time delay. I will also suggest some ideas for a future work with the new tracesystem..

The main purpose of a Flight Data Recorder (FDR) is to facilitate the investigation of incidents. In order to interpret the data that has been recorded in the FDR the data has to be visualized in some way. This can be done with software on a computer or with hardware that is specific for the model of aircraft that the data originates from.The aim of this project is to visualize data for six parameters from the FDR of Saab 2000 in an avionics rig. The avionics rig resembles the cockpit of Saab 2000 and the displays in it are identical to the ones found in the plane. All six parameters are shown on the same display.Due to safety regulation vital systems in aircraft are doubled, with one system on the left side and one on the right.

On 1 January 2005, IFRS (International Financial Reporting Standards)was mandatory for all listed companies within the European Union. The introduction is to create a transparent and consistent reporting. Mainly to provide companies, investors and financiers the same access to world capital markets. Since the introduction of IFRS, the goodwill value is determined by annual impairment tests. If an impairment of goodwill is a fact the goodwill decreases in value.

 The purpose with this thesis was to develop a designguideline which will simplify the development of new products that will be laser welded. The need for this thesis has come forward from the quality problems that Volvo Construction Equipment, Components Division is having with their laser welding manufacturing unit. The reason for the problems emerges from the bad communication between the development unit and the manufacturing unit within the company when the products produced today was developed. This resulted in products that were hard to and in some cases almost impossible to weld. To avoid these problems from occurring again it was needed to gather the experiences within this area and compile it and present in a brief a pedagogical manner. The information for the groundwork of our results has been gathered by interviews of several key persons in Volvo Construction Equipment, Components Division.

Many workplaces around the world use some kind of presentation software as an aid during presentations. At Westinghouse Fuel Service in Västerås they experienced that they didn´t know how to use this medium to its fullest extent. They wanted to increase awareness of presentation skills with PowerPoint among the employees, to improve their internal and external communication. A desire they are certainly not alone to have in the working life.My research studied how to design guidelines for the use of presentation software, so the users can easily absorb the message and find motivation to use the guidelines. In order to adapt the guidelines to their users, and thus create major opportunities for them to absorb the message, I based my study on the concepts legibility, readability and reading value.

The thesis was performed at the lighting company Zpecta AB. Zpecta needed to develop alternative attachment of their LED-luminaire Capella. Today Capella attaches in metal ceilings with four magnets. Zpecta got indications from their customers that there was a need for other attachments. The purpose is to determine the customer?s requirements and the interfaces that are considered for Capella.During the thesis, Capella was only on the market for testing and evaluation.The thesis was initiated to create a specification.

Prioritisation of software requirements is a critical part of the development of software. Whichrequirements and in which order they will be developed is one of the main tasks that requirementprioritisation supports.There are different ways that a requirement prioritisation can be used, for example alone or in agroup and with different methods.The purpose of this report is to map out how you can carry out a requirement prioritisation alonewith different types of prioritisation methods and how you solve the problems that can arise whenprioritisting requirements. This is done by documenting the use of three different types of methodsthat can be execute alone. The methods are "100-dollar test", "Ranking" and "Top-tenrequirements".To be able to prioritise requirements, you need to establish which requirements you shall prioritise.The paper retrieves this information by interviewing stakeholders in the system and analysing theresult of the interviews and the execution of the requirement prioritisation.Three problems arose during that work and I present solutions on these problems. The problemswere 1) equivalent requirements when using the "100-dollar test", 2) low differentiation gradebetween the prioritised requirements in the "100-dollar test" and 3) that the requirements that wereprioritised weren't classified before the prioritisation, which leads to inaccuracies in the resultingprioritisation.The solution to the problems that the paper presents is to increase the amount of distributable unitsin the "100-dollar test" to 1000 per requirement, suggestions of classes of the requirements andthe combination of the methods "100-dollar test" and "ranking" to bypass the equivalentrequirements.The report is written in Swedish.Nyckelord: GoTRIS, requirements retrieval, requirements analysis, Viktoria Swedish ICT,requirements prioritisation, requirements, 100-dollar test, ranking, top 10 requirements..

This thesis for the Master of Science degree was performed at Solectron Corporation in Norrköping. The background for the thesis was a need to develop and build two test fixtures to automatize testing and adjusting of transmitter modules (TX-fixture) and receiver modules (RX-fixture) which are head devices in DWDM-systems. The basic elements for the test fixtures are: Test board, switch board and DC/DC board. The main function of the test board is to handle communication between the transmitter and receiver modules and supply voltage to these modules. The test board was insufficient and modified with a microprocessor to handle the communication between the PC and the receiver module.