Two different methods for measuring biogas production were used, gas meter and gasbags. The gas meters were electronic and counted each time a certain gasvolume passed through them. The gasbags collected the gas that hade passed through the gas meter until a manual measuring could be done. The two different methods gave the same result for a volume at three liters but for a volume around 0,2 liters they did not. Accuracy and precision for the gasbags was more exact than for the gas meters even if the method was difficult with a lot of different elements that could affect the result.

The goals of this Bachelors? Thesis were to establish the production loss through the VTIS1 Pasteur at Arla Foods Linköping dairy and then suggest simple but effective solutions to minimize the losses for each production run. If the timeframe allowed it, some of the solutions would be implemented and tested in full production to determine their impact on economic and environmental savings.The very first step of this project was to establish the statistics over what losses there is in the production pipeline through VTIS1, from milk and powders in mixer tanks to finished and packed products in cold storage. Then, when knowing how much product was actually lost and where, those bottlenecks could be pinpointed and examined more closely. At this stage the focus was switched, from the otherwise complicated and broad manufacturing process, to the VTIS1-aggregate, since early data indicated there were quite substantial losses there.In conjunction with this project Arla Foods purchased an absorption photometer-measuring device (OPTEK AS16) that could be inserted straight into the product stream out of VTIS1, allowing real time measurements of its optical density.

During my practical training I have seen what after-school offers children. Large groups of children and little staff, often results in that the children had to play freely until they go home. Few activities are offered to the children and the staff is busy looking after the children and ensures that they are not fighting.The purpose of this study is to find out how children feel about their leisure activities and if they think they are being offered a meaningful leisure. The main research questions were:How do children experience their leisure-time?Do after-school offers children a meaningful leisure and is it the children's interests and needs that govern the activities and the environment?How do the number of children in the leisure group affect the leisure time?The methods to collect data in the study are observations and interviews.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

Now a day?s there is dramatic change from traditional to digital information processing in construction industry. This change can be visualized in the project concept stage where it now has accessibility to join all the data in one place. Location-based planning technique simplifies scheduling by visualizing the schedule efficiently and has many advantages such as might shortened the project period by about 10 - 20 % if the company uses location-based technology, reducing risks in many ways by maintaining production continuity and identify collisions between things etc. Vico Office software has been used for Location based planning technique and in this thesis.The purpose of this thesis work was to demonstrate how location -based planning technology change the scheduling stage in Peab, potentially reducing the project time.

I examine how relationships between people and objects are created and continues through contiguity every time one use or touch an object and through participation through use and memories. The aim is to continue a relationship and to keep a communication alive with people beyond time and space, then, now and henceforth. I take advantage of and transform the traces in an object that belonged to someone. Parallel I create new space for bodies to put their mark for the first time. I compare my work with the Nordic Museum's task to preserve the present for the future.

During spring 2009 a three meter tall and laughing robot was developed in collaboration between Royal Institute of Technology and Royal University College of Fine Arts. The robots function and esthetics is based on an existing toy robot called Elmo. Elmo is 30 cm tall but now the goal was to make it 1000 times bigger in order to present it on the spring exhibition of Royal University College of Fine Arts. Due to only four months of developing and building time a demand of fast determination and good planning was required. In order to make a good structure for the project it is divided into five phases: Analysis of Elmo, planning, concept development, detail construction and finally product development and testing.In the first phase valuable knowledge is obtained according to the movements and geometry of Elmo.

To be able to move around without having to think about each movement is for most people amatter of course. Todays society contributes to a life at high speed where the sparetime is oftenspend doing somekind of sport, even extreme sports which earlier only a few people wheredoing. This leads to not only good health effects but also to more injuries. One of the mostcommon injuries is the knee injury.Capio Artro Clinic is a clinic specialized in sports medicine and particulary patients with injuriesin knee, shoulder, foot, hip or elbow. They perform a great part of all the crucial ligamentsurgeries in Sweden and has therefor also a lot of patients in need for rehabilitation of the knee.During the rehabilitation the load of the injuried knee is increased in steps.

Uppsatsen handlar om cineliteracy; att öka sin kompetens att tillgodogöra sig rörliga bilder. Jag undersöker huruvida brittiska filminstitutets femstegsmetod är en fungerande modell för att stimulera elevernas lärandeprocess av komplex film. Som exempel använder jag mig av Jacques Tatis film Play Time..

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

The purpose of this essay is to study how the local creators of a "master plan" for the swedish city Kristinehamn, the years between 1940 to -43, looked on their planning. It is an analysis of ideas case study. A hypothesis is upheld for the research: that the local physical planning had largely extended ambitions what regards central state control in a way that is similar to planned economy. Questions that are asked include: Was the planning assumed to be a tool for the state to regulate the environment? Can the planning be seen as a mean to control the society in time and space? The essay search for verification of the hypothesis by a theoretical analysis apparatus made upp of ideal types.

Time Perspective is related to mental and physical health. This study examines the relationship between Time Perspective and perceived stress where Time Perspective was expected to predict the level of perceived stress. Past-negative, Future-negative, Future-positive and present-fatalistic were expected to be positively associated with perceived stress while Past-positive and present-hedonistic were expected to be negatively associated. Measures from the self-assessment forms S-ZTPI, PSQ-recent and CES-D from 445 participants (242 women, 203 men) between 60-90 years were used to examine the hypothesis of the study. Two hierarchical multiple regression analysis confirmed that Time Perspective is associated with perceived stress and in part 2 explains it's variance, one when adjusting for demographic data (.R = .37) and the 2 other when adjusting for demographic data and depressive symptoms (.R = .13).

The goal of this study is to gain knowledge and understanding of how a teacher can apply mathematics with assistance from practical mathematics. Students? point of view on mathematics within practical mathematic lessons will also be examined. Four teachers from preschool to third grade in primary school were interviewed. 30 students from grades one to three were also surveyed. The study shows that teachers see a major benefit when practical mathematics is used in the theoretical teachings of mathematics.