The report is part of the university´engineer program within Industrial Organization and Economics with specialization in Logistics and Managment at Jönköping´s university.Skoghall´s mill underlies a large supply chain, which means there should be a lot of areas in need of small improvement measures. This report illustrates a small part of one of these areas and is focused on the loading distribution services in the terminal Vänern.At the moment there´s a very unequal load of the load carriers SECU box and Container at the terminal. Skoghall´s mill has the desire to equalize the high and low load levels of the 2 loading carriers named previously. One of the options to solve the problem is to set a limit of how much the carriers can load per week or per day. The mill also wants it to be investigated if the proposition would influence the customers in any way and if both the company and its customers could handle a lower level of delivery services in case the proposition was to be applied.The goal to be achieved with this thesis is to provide balance to the unequall loading of the 2 load carriers, SECU and Container, and investigate whether or not the Skoghall´s mill´s customers, could manage the lower degree of delivery service that the proposition would imply.For this goal to be achieved, random sample investigations were taken from orders of a customer that is provided with SECU load carriers and the same was made with a Container´s customer.

This master thesis deals with steel girders subjected to patch loading caused by concentrated moments. There exist no good methods to calculate by hand the ultimate resistance for this load case. In ?tunnplåtshandboken?, (Handbook for sheet metal, which is published by SSAB), one calculation method is presented. It?s however fairly difficult to use, because of many calculation steps and many graphs.

The power consumption has grown rapidlyin the last decade. Fossil fuels and theneed for alternative energy sources aregreat. Ocean waves are a renewable andsustainable source of energy that hasbeen relatively untapped. At UppsalaUniversity research and development havebeen done for several years. Severaltypes of wave energy converters (WEC)have been created.

This report was written by Sofia Ericson and describes the degree thesis with the title: ?Connections between the growing site of bio fuel, the chemical composition of bio fuel ash and the deposit growth in a bio fuel fired boiler.? The purpose of this degree thesis was to avoid melted deposit growth in the bio fuel fired boiler at ENA Kraft in Enköping. Potassium and sodium are known to lower the melting point of bio fuel ashes and are therefore not wanted in the trees in higher amounts than necessary for the growth. Silicon is also known to be important for the deposit growth but it is not possible to say in general if higher or lower contents of silicon is better. The relation between silicon and other chemical substances is more important than the total amount of silicon.

A method for measuring the total impulse from a multi hole diesel injector, introduced inprevious thesis work, ?Development of a method and a device for measuring the momentumrate of fuel sprays?, by Mikael Lindström, has been further developed and tested. The conceptis to simultaneously deflect all sprays from a multi hole diesel injector by using a bell shapeddeflector. The fuel sprays are deflected straight down from their initial umbrella angle, andthe resulting deflection force is measured in a thin strained section of the load cell. The strainis given by three strain gauges, with quarter-bridge circuitry for each gauge.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

This Master?s Thesis aims to illustrate in what ways the two Swedish environmental assessment tools, the Environmental Load Profile and EcoEffect differ and if performed valuations gives different results and environmental goals.The built urban environment causes about half the environmental loading in Sweden. The society?s ambition towards sustainable development has resulted in demands reducing the environmental load. One way to accomplish this change is with the assistance of tools for environmental assessment of the built environment.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

Combustion of fossil fuels is today the dominating source of energy. During combustion,carbon dioxide is formed. The carbon dioxide accumulates in the atmosphere,which raises the global average temperature on earth through the so called greenhouseeffect. The only way to reduce the emissions of carbon dioxide from combustionin a coal fired power plant is through carbon capture and storage (CCS).Post-combustion capture is a technology to separate carbon dioxide from the uegas after the combustion for efficient transport and storage. The steady state operationof coal fired power plants with post combustion capture has already beenthoroughly investigated on a pilot scale, however much work remains to investigatethe plants dynamic operation.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

Tomo Hugglink (TOMO Skog) is an innovation for harvest and transport of biofuels. The system consists of a truck, a chipping unit and crane mounted on a link and a wood chip trailer. The system works in such a way that the chipping unit is disconnected and placed on the site and wood chips are loaded directly into the wood chip trailer.The aim of this study was:- To examine the performance of the TOMO Hugglink system under different conditions such as the size, placement and quality of the pile.- To calculate the cost per raw ton for two vehicle combinations at different transport distances and to examine the effect of a reduction in set-up time and an increase in load weight.- To identify possible improvements with the TOMO Hugglink system.A time study was conducted within the thesis work to make it possible to determine production and time consumption. In the subsequent economic analysis the cost per tone at different transport distances was calculated for two different lorry concepts. Furthermore the effect of a reduction in set-up time and an increase in load weight was calculated.Under current conditions the utilization of the chipper is low and only 29 % of the total system time is occupied by chipping.

The Island of Öland has one of the best wind climates for land based wind power in Sweden. An objective for the Island is to become self sufficient using electricity from renewable source of energy such as wind. There is currently 55 MW capacity installed on the Island and it is estimated that grid congestion will occasionally occur if more than 135 MW was installed.The aim of this thesis is to investigate he possibilities for load management by smart charging of electric vehicles, EV. The definition of smart charging is that the charging is done to some extent with an ICT-system, (information and communication technology) that correlates wind electricity generation to the charging of electric vehicles. The purpose is to avoid grid congestions on the sub-sea cable that connects Öland to the mainland because that in turn would curtail wind energy production.

This report summarizes the development of a calculation program estimating the profitability of converting a peak-load oil-fired boiler to pellets. To convert an oil-fired boiler to pellets a new fuel handling system must be designed. Changes also have to be made to some other components. Since there are many different techniques for transportation, storage and treatment of the fuel only the most interesting techniques from Swecos experience and interest were included in the study.The capacity of the different parts in the system was dimensioned based on the power of the boiler after conversion. To estimate prices, installed power and dimensions manufacturers and distributers were contacted.

The constant need of energy is something that affects us all no matter our current situation. Whether we are driving our car to work, taking the elevator or using the oven to cook dinner we end up relying on energy. Our whole society is continuously striving to achieve a higher grade of efficiency and the process of supplying ourselves with energy is no exception. The importance of appliances in our everyday life cannot be exaggerated and thus the importance of their high efficiency.Efficiency is already a keyword in the appliance industry with labels, stars and numbers helping us choosing the most suitable option for the task ahead. No matter how efficient appliances often use pure electricity as their energy source.

Background: Today, the trademark is the heart of the company and the management of brandimage and identity require certain attention and care. In an increasingly tough business climatewhere the brand today has a central and important role, it is understandable that the companieswant to take maximum advantage of it. In the company the brand is a great resource with analready known identity and established values that can help new products to enter the market. Toextend the brand is a popular growth strategy but it is important to do it properly in order not tofail. J Lindeberg and Peak Performance are two Swedish fashion companies which both havemade brand extensions.