Syftet med denna undersökning har varit att underlätta för företaget Re-Load att presentera sin lastpall som produkt för potentiella kunder. Syftet har också varit att stötta Re-Load till att bli licenserad EUR-pall samt att successivt ersätta befintliga lastpallar och långsiktigt exekvera företagets affärsplan. Målet har varit att undersöka produkten avseende lönsamhet, miljöinverkan och hur den påverkade arbetsmiljön. Under-sökningen har genomförts med ett befintligt flöde där produkten använts och utifrån detta kunde en flödesstudie samt en komparativ produktstudie utföras med en alternativ lastpall. Med data hämtat ur detta flöde utfördes en investeringskalkylering, miljöberäkningar, subjektiva intervjuer samt dokumentation.

The essay shows that temporary agency employees work in a complex business. Both labor and management differs from other businesses in the Swedish labor market. Regarding the unemployment insurance, they have previously been separated from other businesses through legislation. Based on the essay question regarding workers protection has the statutory rights for employees been strengthened. This by the implementation of the directive on manning into Swedish law and now covers all workers in the business.

There is currently no activity or behavior meters validated for sows under Swedish conditions where the sows are loose-housed during farrowing and nursing. An activity meter could in particular be used to detect sows that are getting ready for farrowing. Assistive technology in order to register different behaviors would be extremely useful in research and breeding. In this study, a HOBO Pendant G data logger was validated for two different functions. First, the function as a pure activity meter in which the accelerometer's ability to detect an upcoming farrowing was evaluated, and second, the accelerometer's ability to distinguish between the behaviors standing up, sitting down, lying ventrally and lying laterally on the right and left sides was evaluated. The accelerometer was attached to a collar around the sow's neck, and was recording its location every two seconds for six hours a day for ten days on a total of twelve sows.

This report is the result of a thesis as been implemented during the spring term 2009 atthe University of Gävle.The company Bruks produces mobile chippers which are used for chipping loggingslash, roundwood and parts of trees. The chipper is powered by a separate diesel engineand the chipper can be assembled on trucks, trailers or some other carrier vehicles.When the chip has passed the chipper drum, the chip is collected in an integrated binwhich is mounted on the vehicles frame with dumping yokes. When these dumpingyokes were designed they were probably created with large material dimensions. Theaim with the degree project is hence to study the strengths of materials and, if possible,to suggest an arrangement that can decrease the total weight on the dumping yoke onBruks´ mobile chippers 805 CT.The CAD-program Pro/ENGINEER was used during the project for outlining the 2Ddrawings,as distributed of constructors on Bruks, to solid 3D-parts. The three-dimensionalassembly from Pro/ENGINEER was transferred to Pro/MECHANICA.

Bakgrund och problem: Stora förändringar har skett i tillverkningsindustrin sedan i början av tjugohundratalet. Företagen måste ständigt utvecklas och söka nya sätt att organisera sig för att kunna vara konkurrenskraftiga i dagens globala marknad. Detta föder nya problem och frågor om hur de kan vara kostnadseffektiva och ha en personalflexibilitet som följer volymsvängningarna. Det har funnits bra uppföljningar och kostnadskontroller på kollektivsidan, men inte på tjänstemannasidan. Detta väcker två frågor.

Examensarbetet inom produktutveckling ? konstruktion utfördes under perioden februari till juni 2013 och omfattar 15 högskolepoäng (C-nivå), och är den slutliga kursen inom högskoleingenjörsprogrammet Innovation och produktdesign.Examensarbetet behandlade problematiken kring produktionsanpassning och kostnadsoptimering av två stycken elektromagnetiska omrörare vid företaget ABB, Process Automation, Metallurgy i Västerås. Efter kontakt med handledaren från ABB, Jan-Erik Eriksson, påbörjades projektarbetet med att tillverkningsanpassa konstruktionen av produkterna ORD 43P och EM Stabilizer.För att åstadkomma kostnadsoptimerad och produktionsanpassad konstruktion tillämpade författarna följande produktutvecklingsverktyg: Design for Cost, Design for Manufacture och Design for Assembly. För att kontrollera att konstruktionen blev optimal, men också att den inte brister under belastning använde examensarbetarna det datorbaserade hållfasthetsverktyget finita elementmetoden i CAD-programmet SolidWorks.Val av komponenter baserades på komponenternas pris per kilo.För att välja det optimala materialet, det vill säga högsta hållfasthet till lägsta pris använde författarna materialdatabasprogrammet CES EduPack. De utvalda materialen från programmet kunde inte författarna påfinna som standard på marknaden, varför författarna ändrade strategi till att jämföra och välja material utifrån marknadsundersökning av standardmaterial hos leverantörer.  ORD 43Ps komponenter optimerades konstruktionsmässigt gentemot befintliga komponenter och härvstag och isolerplattor kostnadsreducerades markant.

On November 1989 the Convention on the Rights of the Child was adopted by the United Nations General Assembly. Today more than 20 years later the convention is ratified by all countries in the world except the USA. A question asked is however if the convention after 20 years of development work has in fact accomplished some positive effects for children around the world? The aim of this thesis is to evaluate the implementation of the Convention on the Rights of the Child in selected states and to reach this aim some questions need to be answered: What do the selected states do to realize the best interest of the child?What do the selected states do to guarantee all children?s right to survival and development?Do all children in the selected states have the same right to health and health services?Do all children in the selected states have the same right to education? The material studied in this thesis is those reports that are to be sent periodically to the Committee on the Rights of the Child by all states. The result of this study shows that the Convention on the Rights of the Child has made some positive progresses when it comes to the situation of the child in the world.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

The Production Manager at Atlas Copco AB Craelius wants to adopt a lean approach to become more competitive. This thesis is an exploratory study of the subject and what it means for the business activity and its implementation process.The objective is to provide a basic understanding of lean to the company, and what this means for Atlas Copco AB Craelius. The report describes the industrial revolution in brief. This is because the company itself must understand where certain ways of looking at production management is derived from. Furthermore, it provides an understanding of Lean's origins.

This thesis concerns waste management on construction sites and was conducted on behalf of ICA Fastigheter.Areas of concern:How can an environmentally-efficient waste management system on construction sites be defined? What potential exists for exploiting the waste resources that are generated?How can the waste management be optimised by reducing the quantity of waste and by optimal sorting?How can the client of a project influence the waste management?The purpose of the work was to investigate sustainable waste management in the building and construction sector and to highlight waste as a resource from an environmental and economic perspective.The aim of the work was to define an environmentally-efficient waste management system, to analyse the potential that exists in waste management and to draw up guidelines for optimal waste management.The method consisted of a literature study, two visits to construction sites and four interviews.An environmentally-efficient waste management system means that the waste is managed in the following order of priority:Prevention     Reuse  Recycling     Energy recoveryLandfill     The prevention of waste is an important area that has not been adequately explored by the building and construction industry. The quantities of waste could decrease with the implementation of measures such as ordering materials in the dimensions required, prefabricated components, logistics centres with Just-In-Time deliveries, less and improved packaging and less wrapping. The reuse of waste materials and temporary apparatus as well as the use of a return pallet system are examples of reuse that reduces the quantities of waste.In most cases the source sorting work is a matter of course and the proportion going to landfill is down at a low level. The source sorting can be optimised by sorting all materials that can be reused and recycled to use them as a resource.

The graduation essay has been carried out in co-operation with Kalmar Industries in Lidhult, Sweden. The purpose of our essay was to develop a complete construction solution on a hoist that could lift a laying wheel, lift it up and then turn it 90 degrees. After that the wheel shall be placed in a special holder.The background of the essay is a record of reports of damage wheels when they been incorrect lifted with a forklift. The hoist shall be used together with the same forklifts that manage the wheels today. Together with our instructor at Kalmar Industries we developed a requirement specification and from that we got free hands.However this was not the main task from the beginning, then a simular hoist should be develop but used directly in the assembly workshop without using a forklift.We started to find principle solutions that later was evaluated against the requirement specification.

This report is the result of a thesis carried out at the Department of Innovation, Design and Technology (IDT), at Mälardalen University on behalf of ABB AB Machines.The year was 1988 when ASEA and Brown Boveri formed a joint venture under the name ABB (Asea Brown Boveri).We perform our thesis at the division Discrete Automation and Motion where they primarily develops, manufactures and sells synchronous and asynchronous AC motors and generators.The main purpose of this thesis was initially to write a general packaging instruction, but the priority changed to develop more specific packaging instructions for Rotors, Stator gables, Bearing support and Outer Cover (plates) instead.The work started off to deal with a problem about that the staff had to start its work to grind away rust on the stator gables due to those stored outdoors. The result was mainly an investment in a new gable rack so that the material can be stored inside, as well as a packing instruction as it was originally intended.The problem on the bearing supports were that the staff thought it was demanding and difficult to clean them from the rustproofing they were greased in. If it is not possible to remove all rust protection it can cause the paint to not attach properly. After having compared with similar articles a test were done to order a pair of bearing supports without corrosion inhibitor, which gave good results. This initiative also set in motion a process to do the same for more different items.For special pallet, a survey were made of the process with two different VSM and a calculation of how much ABB would earn at ordering more special pallets than getting the material delivered on the A-pallets.

AbstractIn this bachelor thesis I discuss and analyse the current situation of the Venezuelan democracy. By using a theoretical framework based on the theory of horizontal accountability, I focus on the interaction between different institutions and branches within the state of Venezuela. The analysis focuses on the strenghts and flaws of the newly accepted constitution, and to what extent the institutions of checks and balances remain true to the laws and the constitution of 1999. My conclusions are that in terms of vertical accountability, the Chávez-regime acknowledges a wide popular support for their governmental actions. In contrast, the incumbent administration shows almost no respect for horizontal accountability.

En av Parocs produkter är sandwichpanel som är ett byggmaterial som kan variera i storlek och tjocklek och är funktionellt och smidigt. Uppdraget var att designa ett beslag för panelsystem som minst 50% av Paroc Panel Systems kunder skulle föredra framför de gamla, främst med avseende på estetiken, men även baserat på lätthet att montera och kostnad av beslaget. Projektet skedde i samverkan med företaget Paroc Panel System AB och ur förundersökningen framkom att utseende, monteringsmöjligheter, egenskaper såsom materials livslängd och hållfasthet och totalkostnad var viktiga krav som ställdes på produkten. Lösningsförslag med fokus på flera viktiga aspekter togs fram och kombinerades till olika koncept med hjälp av en så kallad morfologisk tabell. En konceptutvecklingsfas ingick där hållfasthetsberäkningar och materialval var avgörande.

This examination work is the final work in our education to become a Bachelor of Science inMechanical Engineering by the University of Lund.The main purpose with this work has been to develop a new effective material handling system for TPPM AB in Lund since the existing system starts to become out of date. The future system that is going to be installed shall have the capacity to support all machines with unit-, semi- and finished goods during full production. The work has also included studying the possibilities to change the material flow in a positive way between the storage and the production when one is using existing buildings.During our work we have been used a simulation program called AutoMod, performing company visits, interviews and reviewed internal and external information to create a picture of what the best conclusion can be. During the work we have contacted five suppliers to receive system solutions and quotatioris. The suppliers, which have been contacted, are Swisslog, Moving, Rocia, Christensen & Hansen and ABB.