This thesis is the result of the investigation and solution of a mechanicalproblem regarding flywheel malfunctions. A flywheel is, in short, a devicethat relies on a rotating object?s moment of inertia to store energy overshort time spans. This project is part of the development of a fourthflywheel prototype at the division for electricity at Uppsala university,which uses magnetic levitation to keep a hollow cylinder rotating at veryhigh speeds inside a vacuum chamber. Should the magnets fail however, orsome other error occur that leads to an uncontrolled state of rotation, thecylinder needs to be stabilized mechanically by a device usually referredto as ?back-up bearing?.

At the beginning of the 1970´s forestry feared an imbalance in the future wood supply. Because of this anticipated "timber slump" forest companies undertook a variety of measures to counter this. One of these measures was the introduction of exotic tree species. The choice finally ended up with lodgepole pines which were considered a fast growing tree species compared to our native tree species. Theambition for the new lodgepole pine stands were to run these with rotation periods of between 40-60 years, thus smoothing out the ?timber slump? that was anticipated.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

Projektet bestod i att utveckla en anläggning för personsanering av biologiska-, kemiska- och nukleära stridsmedel, en så kallad NBCanläggning. Arbetet har initierats av Marinens Sjösäkerhetsskola i Karlskrona. Under arbetets gång har Fredy Olssons produktutvecklingsmodell tillämpats. Projektets tyngdpunkt har legat i att söka komponentalternativ för de önskade ändamålen och för att uppfylla kraven. Anläggningen är långt ifrån produktionsklar, men ett omfattande grundarbete har gjorts inför ytterligare bearbetning och komplettering med beräkningar samt vissa komponentval..

?Medicines are available in different forms and often have different types of compound components. More and more drugs are found on the market. This means that professionals who handle different medicines must have access to more and more information.The information available includes information about side effects, active substances, interactions and pill identification. You may want to access different information, depending on your profession.

This thesis aims to discuss how an information system and its users may adapt to each other. The main discussion is how to create an information system that is adaptable without losing its organising properties. The thesis uses a holistic approach to the topic and the areas being dealt with are information architecture, interactive information retrieval and information searching. The practical work consisted of constructing a database for Autoliv?s Research and Development branch.

This study was carried out at the request of the Swedish forest company Sveaskog which is an important producer of logging residues (branches and tops) intended for energy production. The company wanted to increase the average dry content to 60 percent in their delivered logging residues. At the time when this study was initiated, the dry content in the chipped logging residues originating from the Bergslagen district was at 52 percent. The aim of the study was to find out how windrows of logging residues could be arranged in order to help obtain desired properties such as increased dry content. Sveaskog had developed a system for evaluation of windrows and a standardized form was utilized to describe different properties of the windrows.

In order for companies to be competitive they perform different types of development projects.  Due to globalization a greater focus is added on costs, not least on costs in development projects. Project controllers are involved in development projects in order to review the financial aspects. The authors have examined the role that project controllers hold in respect of two Swedish manufacturers, Volvo CE and Scania CV. The investigation has revolved around three main issues where the authors conducted interviews with controllers that do not work in development projects and project controllers in development projects. The goal of the interviews was to gain a greater understanding of the role of project controllers, how this role will differ from those that do not work in development projects and the difficulties faced by project controllers.

This work is a GIS study of fishing rights distribution between different categories of ownersand properties in the Stockholm Archipelago. The purpose was to create basic data used toestablish fishing laws and restrictions within the Stockholm County.Stockholm?s archipelago consists of a unique environment and is the natural life andreproduction environment for ? of Sweden?s reproducing fish species. The increasingpressure from fishing, tourism and weekend population increases the need for an efficientfishing administration to prevent impoverishment and to ensure the biological diversity inSwedish fishing waters. There is an increasing need to review fishing administrationmethodologies, as well as studying the categories of ownership and properties located insensitive areas and areas influenced by physical disturbances in order to establish effectivelaws and restrictions.The Swedish fishing rights for an area are currently not connected to the ownership of theproperty to which it belongs.

Buildings worldwide account for 40 % of the total energy use. Climate change is of increasing importance, but few are willing to reduce their standard of living or get a higher cost for the change. Energy efficiency of existing buildings gives the greatest benefit economically and environmentally. The real estate company Klövern AB manages 46 properties in Karlstad. Heating is the major cost of the total operating costs of real estate. Rising energy prices increase the need for Klövern AB to improve energy efficiency and to investigate alternative sources of heat.

A pavement construction designed to cope with the different type of traffic loads; it is exposed to and at the same time it can resist the effect of the climate. A road structure consists of sub- and superstructure which is divided by a boundary known as terrace. During the construction of unbound layers (base course and sub-base course) in the superstructure, it is always ensured that the material meet the requirements for bearing capacity and the degree of compaction. These parameters are controlled by various laboratory tests and control methods. To obtain increased knowledge of the material and improve the quality of the compaction in the field, it is necessary to perform laboratory tests in order to determine material properties.A base course material 0/ 32 mm limestone from Gotland (Hejdeby) was investigated in this study.

AbstractA master thesis in business administration 30 hp, Jönköping International Business School, Spring semester 2012.Authors: Sarah Henningsson & Jim BörefeltSupervisor: Urban ÖsterlundTitle: Commercial real estate investment ? Factors from an investor perspectiveBackground and problem: In this study, we focused on the real estate investor and the factors and issues that may arise and affect real estate investment decisions. It has been put in relation to the other parties in the process of assessing and affecting real estate investment decision. The parties that we studied are real estate investors, banks, brokers and appraisers.Purpose: This study aims to describe and explain the factors that affect commercial real estate investments for investors, credit assessment conducted by the bank and valuation made by the broker and appraiser.Delimitations: We have chosen to limit the study to commercial real estates including residential, retail and office properties, industrial properties and combinations thereof. Agriculture buildings and forestry plots are not examined.

Uppdraget som gavs av Brimer VA Produktion AB i Osby var att ?föra fram deras nya vattenledningssystem i ljuset?, göra en FEM-beräkning på en detalj i systemet och ta fram en ekonomisk samt teknisk jämförelse mot det traditionella vattenledningssystemet. Bästa lösningen på uppgiften var att visualisera vattenledningssystemet med hjälp av animerade filmer. Detta med tanke på att visualisering har ingått till stor del i utbildningen Virtuell Produktutveckling & Design..

AbstractA master thesis in business administration 30 hp, Jönköping International Business School, Spring semester 2012.Authors: Sarah Henningsson & Jim BörefeltSupervisor: Urban ÖsterlundTitle: Commercial real estate investment ? Factors from an investor perspectiveBackground and problem: In this study, we focused on the real estate investor and the factors and issues that may arise and affect real estate investment decisions. It has been put in relation to the other parties in the process of assessing and affecting real estate investment decision. The parties that we studied are real estate investors, banks, brokers and appraisers.Purpose: This study aims to describe and explain the factors that affect commercial real estate investments for investors, credit assessment conducted by the bank and valuation made by the broker and appraiser.Delimitations: We have chosen to limit the study to commercial real estates including residential, retail and office properties, industrial properties and combinations thereof. Agriculture buildings and forestry plots are not examined.

Mechanical relays are more and more being replaced with semiconductortechnology. In this thesis it is investigated if and how the larger loads couldbe controlled by transistors. The main part of this work aims to create andverify a solution that can control the starter motor, as well as protect it incase of any failure. The different malfunctions that the solution protectsagainst is high current, too high peak current, low current, maximum cranktime and minimum cool off time. The timers also protect indirectly againstoverheating of the starter engine.The transistors used are BTS555, from Infineon.