This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

Due to the requirement for reduced use of insecticides and the lack of competitive mechanical plant protection, you need a scarification with good result. This is often no problem to perform in normal terrain without technical barriers. However, in difficult terrain with large number of rocks and steep slopes, the result would be worse. The purpose of the study is, that in these areas with difficult terrain, to find out the scarified areas quality, describe the non-scarified areas conditions and find out where the limit is for the use of a traditional disc trencher. Findings indicate that there are usually not the machine that is the limit, but the driver of this.

The environment has become an important part in people´s lives, and in today´s society stakeholders demands have increased upon companies when it comes to sustainability reports. How these sustainability reports are designed depends on whom it?s for, laws and regulations, and the companies own norms and values. The purpose of sustainability reports is to measure, monitor and compare a company´s enviromental impact. It?s not only about integrating economics, but also enviromental and social standards together to get both financial and competitive advantages.Sustainable Value method is a new model and is the first real method that can be used to evaluate a company´s resources, both financial, social and enviromental to a sustainable value.This model is used to compare the resource efficiency between companies.In this thesis, a documentary study with an experimental approach has been made.Sustainability reports from six selected companies (in the engineering and forestry sector) have been investigated with respect to their accounting for carbon dioxide, and an experiment using the method ?Sustainable Value Approach? was subsequently performed.

This bachelor thesis is intended to point out differences within the supervisors? role and contribute in making the role more attractive. At present the information about how the supervisors? perspective varies on the supervisors? role and the introduction to it depending on work experience and education is unknown. Further it was investigated why the supervisors? role is seen as an entrance to the building industry and how to develop the role to encourage the supervisors to stay longer within it.In the collection of data we have been interviewing supervisors and studying literature.

Today the competition in the automobile industry is getting all tougher. The technology behind cars becomes more advanced. To get ahead of competitors car companies has to look into new areas of innovation.One important area is vehicle safety. Bigger companies have come so far in vehicle safety that difference between cars more depends on the car type (size) than the technology behind it.There is one area where vehicle safety that still has great opportunities for improvement, which is in active safety. The term active safety states that the car has the ability to identify treats and automatically respond to the treats.

RISKfree ? ett system för riskhantering inom programvaruprojektI dagens IT-centrerade värld sker utvecklingen av hårdvara och programvara i en rasande takt. Om ett företag skall ha möjlighet att vara konkurrenskraftigt i denna utvecklingstakt, krävs det snabba och effektiva metoder i utvecklingsprocessen. Dessa krav från omvärlden på nya och mer komplexa produkter och tjänster innebär ofta nya och större risker för ett utvecklingsprojekt; både ekonomiska som tidsmässiga.Analyser av programvaruprojekt som har misslyckats visar att många av deras problem och risker kunde ha undvikits eller åtminstone drastiskt reducerats med hjälp av riskhantering. Oftast är det en optimistisk entusiasm över projektet som överskuggar viktiga varningssignaler om risker och problem enligt B.W.

The Airsoft Community always search for realism and optimal performance.When the performance and/or the realism in your AEG1 aren?t enough you turn to modifications toimprove the weapon. But to manufacture such modifications isn?t that easy, hence you turn tocompanies that are specialized in creating such devices.The goal with this project is to create a prototype of a modification called ?Programmable MOSFET?and targets optimization of the electrical components within the AEG. This means that you digitalizethe control of your AEG thus entails new functions and more stability to the system that isn?t possiblewith its mechanical predecessor.A prototype has been manufactured and programmed with functions according to requirementspecificationsthen it was tested on an airsoft-gearbox with rewarding results.

Målet med detta arbete är att undersöka och analysera en byggnad från miljonprogrammet i Helsingborg göra gällande energiberäkningar. Dessa beräkningar ska mynna ut i olika förslag till hur man skulle kunna styra upp en renovering av dessa byggnader så att de uppfyller de nya energikraven samt skapa en mer tilltalande estetisk byggnad..

Utvecklingen av informationssystem utförs vanligen med hjälp av en systemutvecklingsmodell där kravhanteringsaktivitetens (Requirements Engineering ? RE-processen) syfte är att samla in och bearbeta kundens alla krav på systemet. Den slutliga produkten av RE-processen är en kravspecifikation där alla kraven gällande exempelvis systemets funktionalitet, syfte etc skall specificeras.Det är inte alltid självklart vilken information som en kravspecifikation bör innehålla då detta dokument kan för både kunden och leverantören ses som ett kvitto på vad som skall utvecklas och hur det skall gå till. Dokumentet skall nämligen fungera som ett underlag för de så kallade implementations- och designaktiviteterna i systemutvecklingsarbetet samt fungera som ett underlag för diskussion och kontrakt mellan leverantör och kund gällande utvecklingen av informationssystemet. Kravspecifikationen bör därför innehålla komplett och förståelig information så att detta dokument uppfyller sina syften.

Webbplatsen fass.se är idag anpassad för folk inom vården. Nu vill man göra en ny version av webbplatsen som är anpassad för allmänheten. Detta ställer stora krav på användbarhet. Så länge någonting fungerar som det ska och går precis som man tänkt så tänker man inte på det. Saker och ting kan vara enkla att lära sig och de kan vara effektiva att använda när man har lärt sig det.

In this report a new gear concept is evaluated using the magnetic finite element method (FEM)software MagNet and Ansys as well as the mechanical FEM software Abaqus. The gear conceptis evaluated in terms of maximum torque capability, torsional stiffness, gear ratio and efficiency.ABB Corporate Research has proposed a new gear concept which should be less expensive thangearboxes used today. The new concept is called aMagnetic Harmonic Traction Drive and usesthe principles of a harmonic drive gear to achieve a high reduction ratio. The gear conceptreplaces the wave generator used in traditional harmonic drives with magnets and uses tractioninstead of gear teeth to transfer the torque. The main components in the gearbox are the magnets,the flexspline, the magnetic portion and the circular spline.

This diploma work project is a product development project which purpose is to redesign a braking system for a walking frame. The system that was developed diverges the force from the user to braking power, and includes a service brake as well as a parking brake. The most important components of the system are a grip handle on where the user holds on to and a braking handle on which the user operates the brake from. The system also includes a power transmission component, braking package and other mechanical components. All of the components wasn?t developed in this project, several off them has been reused from the existing system.This product has been developed to meet the requirements and standards presented from the principal, Ahlberg Leber.

There are several methods and models within the areas of software engineering on how to proceed during a software development process. For each of these methods and models there are benefits and drawbacks, depending on how you choose to look at them. A difference of principle between the different models is that they either advocate iterative development or not. In parts of software engineering one makes use of different methods depending on which is most fitting in a specific situation. There are several methods on how to recieve more qualitative data from the end-users during the requirement collection, but the reappearing pattern is still user centric participation, which means that the user participates more actively in part of or the entire development process.

The report aims to describe the austenitic stainless steel Sanicro 25 from a thermomechanical point of view. The thermal and mechanical properties of the material make it suitable for use in coal ? and thermal power plants. By the use of Sanicro 25 it would be possible to bring the efficiency of these plants up while bringing the carbon emissions down.A material model is created from material testing and validated through simulation in the finite element software Abaqus. The model that has been derived describes the material behavior during loading and stress relaxation for the first cycle in a thermomechanical fatigue test well.

Syftet med detta kandidatarbete är att testa en arbetsmetod som skiljer sig ifrån det en mindre grupp i vanliga fall använder sig av: en komponentbaserad arbetsprocess för att utforska och sammanställa arbetserfarenheten med den komponentbaserade arbetsmetoden, utvecklar vi därför ett digitalt spel..