The initiative for this project was taken by Benteler Engineering Services, as a result of having identified areas of improvement, in designated accessible areas like the wheelchair spot onboard buses. Depending on a wheelchair to be able to move around can understandably be challenging.Public transport is a common good in today`s society, however despite the measures taken towards adjusting to accessible needs, the majority of those being disabled chose different alternatives of transportation. This is due to reasons such as the drivers' poor attitude, furthermore the limitations of the space allocated to accessible needs, as people with strollers also use these spots onboard. Also, some wheelchair users find the rides unsafe, as they could easily fall over during without the appropriate space for them onboard the buses etc. These are only a few reasons why other options are sought out, i.e.

The object under investigation in this Master?s thesis is students? information use in connection to Bachelor thesis writing. The purpose of the study is to increase understanding of why nursing students and product engineering design students are using information in such different ways despite their comparable starting point. The empirical material consists of 18 student theses and a document comprising directives for thesis writing that are analysed from three different theoretical perspectives. A citation analysis of all 18 theses is carried out.

Under framtagandet av nya produkter måste ett antal prototyper tillverkas för att verifiera konstruktionen. För en metodingenjör som tar fram reparationsmetoder innebär prototyptillverkning att tankar som växt fram under utvecklingsfasen kan provas för första gången på en fysisk produkt. Detta sker relativt sent i produktutvecklingen och eventuella ändringar som kan uppstå på grund av att servicevänlighet inte uppnås blir mycket kostsamma. Om däremot prototypen där metoderna verifieras för första gången är digital och detta sker tidigt blir kostnaderna för eventuella ändringar avsevärt mycket mindre. Modellen som ligger till grund för metodstudierna kan sedan används för att skapa ett utkast till service litteratur, detta medför att även den delen av slutprodukten kommer att vara i fas med övriga utvecklings avdelningar. Under detta projekt har en digital prototyp av en Scania motor använts för genomförandet av metodstudier.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

Syftet med rapporten var att studera möjliga återvinningstekniker för Ragn-Sells. För detta användes litteratursökning och intervjuer. Återvinningstekniker som studerats är mekanisk bearbetning, mekanisk återvinning, kemisk återvinning och viskostillverkning. Flera underklasser till dessa metoder studerades också, liksom flera sätt att tillverka återvunna produkter. Rapporten nämner ett urval av återvinningstekniker och försöker inte nämna alla tillgängliga återvinningstekniker.Återvinningsteknikerna har sorterats enligt prioriteringen i EU:s återvinningsdirektiv (2008/98/EG).

Detta examensarbete är resultatet av en utredning av produktionsbegränsningar och produktutveckling på Volvo Construction Equipment AB Component Division i Eskilstuna. Produktionssystemet på Volvo CE genomgår en stor förändring då det går från att fungera som en funktionell verkstad till att bli flödesinriktat. Detta gör att helt nya krav ställs på produkternas konstruktion och utformning. Det är nu inte möjligt att anpassa maskinerna eller operationsföljderna efter artikeln i samma utsträckning som tidigare, man kommer att vara tvungen att anpassa artiklarna efter produktionslinan. Därav har en litteraturstudie inom Concurrent Engineering gjorts som belyser hur man bör jobba som organisation och vilka verktyg man har till sitt förfogande, för att utveckla produktionsvänliga produkter.

?Mechanical debridment ? A studie in irrigation optimization? is a final thesis which was executed by Fredrick Ekman, in close collaboration with the other group member Mikael Johansson, during the spring 2012. The thesis was carried out through Karlstad University Faculty of Technology and Science in the study program of Innovation and Design Engineering (180 ECTS credits). The client of the project was Medilink AB located in Lindesberg, and the contact person was Nils-Erik Söderström, Chief Executive Officer. The project was supervised by lecturer, Lennart Wihk, and examined by lecturer and professor Fredrik Thuvander at Karlstad University.

The BSC is a widely used management tool that is turning the vision and strategy into operational goals. However, after analyzing the criticism received by the BSC, it seems as if its internal focus, rigidity, static-ism and mechanical mindset limits the company?s ability to create a strategy that takes important external factors into account. As we see it, the BSC?s limitations can create a risk for strategic inertia.

The purpose with this thesis is to get a compilation of all the critical bolted joints of all enginesproduced at LV Motors. ABB LV Motors produces induction engines with seven shaft heights. Eachengine size exists several variants of components ex. standard shield and flange shield. Depending onwhich components the engine is equipped with arises various types of strains in the engine's parts,certain assembly ways are more favourable than other.The most critical parts in the engine from a mechanical point of view are the screw units betweenshield/stator, feet/stator and bearing cover/shield.

Bakgrund: Produktutvecklingsprocessen har på senare tid kommit att ses som en strategisk aktivitet som är avgörande för företagets överlevnad eftersom produktens utförande och kostnader till stor del fastställs innan tillverkning påbörjas. ?Target Costing? har sitt ursprung från Toyota i Japan och är en metod för strategisk kostnadsstyrning som har vuxit fram för att tidigt styra kostnader. Metoden används för att integrera kostnadsstyrning i produktutvecklingsprocessen i samstämmighet med kundkrav och företagets egna vinstkrav.Syfte: Syftet med studien är att beskriva och analysera hur ?Target Costing? används i produktutvecklingsprocessen på Volvo Construction Equipment i Braås för att ge kunskap till nya potentiella användare.

There are no reliable, objective and simple methods today for measuring pain in horses. The purpose of this study was to evaluate and describe measuring of mechanical nociceptive threshold (MNT) values with a pressure algometer in clinically pain free riding horses at the riding school of Strömsholm. In this study there were 24 horses. Tape recording and electromyelografi (EMG) was used in an attempt to increase objectivity in the examination. MNT increased with age, however sex and colour had no influence.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.