Previous studies of central tire inflation (CTI) in truck transport of roundwood have shown potential benefits to include more even wood flow and reduced road damage. The greatest benefits are found to be during periods of low bearing capacity such as spring thaw. No previous studies have examined geographical variations in the potential benefit of CTI-equipped trucks. The aim of the study was to develop and use a simple method for geographically prioritizing the use of CTI-equipped trucks within a forest company´s sector of activity.The host company for the study was Holmen Skog. The area studied consisted of Holmen Skog?s entire sector of activity extending from the province of Västerbotten to the province of Småland.

The Island of Öland has one of the best wind climates for land based wind power in Sweden. An objective for the Island is to become self sufficient using electricity from renewable source of energy such as wind. There is currently 55 MW capacity installed on the Island and it is estimated that grid congestion will occasionally occur if more than 135 MW was installed.The aim of this thesis is to investigate he possibilities for load management by smart charging of electric vehicles, EV. The definition of smart charging is that the charging is done to some extent with an ICT-system, (information and communication technology) that correlates wind electricity generation to the charging of electric vehicles. The purpose is to avoid grid congestions on the sub-sea cable that connects Öland to the mainland because that in turn would curtail wind energy production.

Detta examensarbete har gjorts på uppdrag av SP Maskiner AB och berör längdmätningsenheten på skördaraggregatet SP451LF. Pulsgivaren i den befintliga längdmätningen anses inte nå en acceptabel livslängd och därför skall ett sensorlager prövas som ersättare.Uppdraget består i att söka ett lämpligt sensorlager, dimensionera en komplett mäthjulslagring samt att ta fram ett konstruktionsförslag till prototyp på längdmätning.Arbetet begränsas av att den omkonstruerade längdmätningen skall passa på SP451LF aggregatet. Det betyder att längdmätningens infästning mot aggregatet inte får förändras och dess yttermått måste hållas inom de gränser som aggregatets chassi tillåter..

Stabilization of subgrade is an internationally common technique to improve the characteristics of a soft soil. Improving the stiffness and bearing capacity of the subgrade enables the pavement to be designed with reduced depths of subbase and basecourse aggregates. This makes the stabilization technique both economically and environmentally interesting. Both natural and stabilized soils have high inherent property variability that should be considered when the characteristic value is derived. By analyzing the spatial variability in stabilized and natural subgrades it is possible get the parameters needed for reliability?based modeling of soil properties.

This master of science thesis is focusing on how the fault handling on hardware connected toa control unit on a Scania vehicle is working. To the hardware counts buttons levers, sensorsand CAN. The work has been concentrated upon how the fault handling is working and if it ispossible to find any new fault modes.The control unit that has been studied is called the Coordinator and is the core in Scanias threenetworks of control units. The Coordinators work is to transmit messages between the threenetworks and to process signals from buttons, levers and sensors. The values is then usedinternally or is sent to other control units on the CAN networks.

The district heating load is seasonally dependent, with a low load during periods of high ambient temperature. Thermal energy storage (TES) has the potential to shift heating loads from winter to summer, thus reducing cost and environmental impact of District Heat production. In this study, a concept of high temperature borehole thermal energy storage (HT-BTES) together with a pellet heating plant for temperature boost, is presented and evaluated by its technical limitations, its ability to supply heat, its function within the district heating system, as well as its environmental impact and economic viability in Gothenburg, Sweden, a city with access to high quantities of waste heat.The concept has proven potentially environmentally friendly and potentially profitable if its design is balanced to achieve a good enough supply temperature from the HT-BTES. The size of the heat storage, the distance between boreholes and low borehole thermal resistance are key parameters to achieve high temperature. Profitability increases if a location with lower temperature demand, as well as risk of future shortage of supply, can be met.

The global climate-change means increasing mean-temperature and higher precipitation in Sweden, which leads to shorter periods of frozen ground in the forest. At the same time the harvesting machines are getting bigger and more powerful. The forest industry aim at an even wood flow, and the ground damage has to be as low as possible. The two biggest causes for ground-damage is the bearing capacity of the forest ground and the ground-pressure of the harvesting machines. The aim of this study was to find out some rules for the machine choice considering ground pressure, when harvesting on ground with low bearing capacity.A field study, using a Valmet 890.3 forwarder, was carried out where different ground pressures and their effect on the ground were tested on two different types of ground.Additionally, an inventory of damaged harvesting grounds was made.

This work is a part of the project ?Våtmarker i odlingslandskapet ? uppföljning av miljömålen? (Wetlands in arable land ? following-up of the environmental goals). The main objective with this project is to study nitrogen and phosphorus retention in a constructed wetland by using mass balance calculations. Continuous measurements of nutrients and water flow through the inlet and the outlet of the wetland are made. However, substantial amounts of nitrogen and phosphorus were assumed to reach the wetland with a drain-pipe transporting wastewater from nearby houses (10 persons).

The purpose with our thesis is to understand and explain the advantages and disadvantages there is with the self scanning system. The advantages and disadvantages we will highlight from three different angels; the store management perspective, the staff perspective and the customer perspective. These three perspectives will together form an overall perspective over the advantages and disadvantages as the self scanning system has contributed with. Finally we will highlight the differences and resemblances we have found between the perspectives.Through a qualitative approach we have gathered data to our thesis. Furthermore we have based our theory chapter and our empirical chapter on the base of Grounded Theory.

The objective of this thesis was to get more knowledge about how to design a dairy farm reducing the working hours and the work tasks whit high work load. I will try to reduce the working hours and the tasks whit high work load on my own farm witch I am about inherit. Today, the old stanchion barn has room for about 60 cows and 74 young cattle and need two men to run it every day. The total acre is 188 hectare, 100 hectare forest, 65 hectare farmlands and 23 hectare natural pasture. I have studied two solutions. In the first solution, I will use my old barn for young cattle and build a new barn for the cows.

Piled friction soil show a set-up which is increasing with the time after installation. The cost could be reduced if the set-up had been taken into account when designing but in Sweden it is very unusual to do that. Previous studies showed that set-up can vary between 25 % and 75 % during the first 90 days after pile installation. This showed that the effect of the phenomenon is difficult to predict. A study involving five projects have been carried out by specifying certain parameters like pile type, method for pile installation and test method for measure the bearing capacity in friction soils located in Sweden.

This report describes the master thesis project ?Weight Optimization of a Composite Chassis for a Multimodal Lightweight Vehicle? which is a part of the Master program in Naval Architecture and a part of a research project at the Centre for Naval Architecture, KTH. Demands on smart and energy efficient transport solutions are continuously increasing. In the Stockholm region the citizens are expected to increase with 25% and the road vehicles with 80% until 2030, putting high demands on the traffic system. Using a small multimodal vehicle deals with this problem and uses both the land and waterways for transportation.

Every day we make numerous decisions. Some are better than others. Intuitive decisions usually results in less good decisions when we do not reason about our choices. Research has been interested about the process that is behind how we make good decisions. Decisions we face every day, such as when we shop, determined using various mental shortcuts that we use unconsciously.

In this thesis a concept for floor hatches for foam pits has been developed. Since there is an existing solution that is powered by hydraulics and is expensive, the goal was to develop a cheaper solution, as simple as possible.A number of different concepts were developed and evaluated. A concept with five sections that are pulled to the side and stacked on each other was chosen as it was thought to have the lowest risk of crush injuries and to be easiest to manage and control. In the opening behind the foam mattress a lifting table is placed to regulate the height of the stacked sections.To be allowed to be installed in the floor of sports halls the sections must be dimensioned according to the construction standards for these types of buildings. Different dimensions of beams in steel and wood materials were evaluated and of those, who lived up to the requirements of the standard, a concept was chosen.

At the moment in central Täby there are small district heating network operated by Fortum Heat. The distribution network has an annual heat demand of about 70 GWh, which is supported by the network's two plants, Galten and Farmen. Täby as a region is rapidly growing and there are grand plans to develop the area. Estimated market potential for a future district heating expansion in Täby is very high and as early as in 2007 Täby decided to invest in a large-scale expansion. In autumn 2009 Täby did a procurement process, known as the ?Täby initiative?, to find a partner that could implement those expansion plans. To secure a cheap basic production the partner also need to build a power plant at Hagby recycling center. Despite high interest during initial state of the process, only one procurement offer were received and Täby suspended the contract in March the following year.