This master thesis was initiated with the aim to answer at what level of installed capacity of wind power in the northern parts of Sweden it would be beneficial to improve the transmission capacity from the northern Sweden. During the process of this work the aim has changed to try and create a model that can be used to analyze how well the hydro power installed in the northern Sweden can even out the quick changes in wind power production.To create a good model of all hydro power in northern Sweden is a very large job, unfortunately too large for a master thesis. This report therefore ends with an extensive analysis of the simplifications that have been made and their effects as well as a list of the future work that has to be done.The model that has been created have shown to be effective and produce good results. The conclusions that can be made is that the northern Swedish hydro power have very good possibilities to balance the wind power production. Only a few cases where water have been spilled even though there has been some free capacity has been discovered.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The exhaust arrangement on a Scania V8 consists of one manifold at each bank connected to a twin entry turbine (8-2-2). A study in GT-Power has shown improved performance and reduced cylinder to cylinder variations using two manifolds at each bank in combination with a single entry turbine (8-4-1). This thesis work analyses the difference in performance shown in simulation and verify it by engine test.The initial work was focused on simulation in GT-Power. Investigating how exhaust manifold volume and pulses effects the turbine efficiency and the mean effective pressure during the gas exchange. To verify GT-Power simulations four engine tests with different exhaust arrangement have been made.The results from GT-Power simulation indicate that a larger exhaust volume improve the turbine efficiency.

In Uppsala CHP Plant, there are six pressure reducing valves to reduce the pressure from 15 to 3 bars, before six absorption heat pumps. During the process the energy is conserved but losses occur in form of exergy. The aim of this thesis is to reduce the losses of exergy. This can be done by letting turbines replace the pressure reducing valves.In this thesis an investigation has been done of the conditions today, the conditions after the change from pressure reducing valves to turbines and a comparison of three different types of turbine solutions. The three examined solutions are one turbine, several helical screw expanders and several small turbines in parallel with asynchronous generators.The six absorption heat pumps have been divided into two groups; one group of four and one group of two absorption heat pumps.

This master thesis was initiated with the aim to answer at what level of installed capacity of wind power in the northern parts of Sweden it would be beneficial to improve the transmission capacity from the northern Sweden. During the process of this work the aim has changed to try and create a model that can be used to analyze how well the hydro power installed in the northern Sweden can even out the quick changes in wind power production.To create a good model of all hydro power in northern Sweden is a very large job, unfortunately too large for a master thesis. This report therefore ends with an extensive analysis of the simplifications that have been made and their effects as well as a list of the future work that has to be done.The model that has been created have shown to be effective and produce good results. The conclusions that can be made is that the northern Swedish hydro power have very good possibilities to balance the wind power production. Only a few cases where water have been spilled even though there has been some free capacity has been discovered.

In this thesis an energy analysis of ethanol production at the ethanol plant of Lantmännen Agroetanol in Norrköping has been performed. The ethanol plant has been studied in combination with Händelöverket, the combined heat and power plant which provides the ethanol process with steam. The purpose of this study was to determine the energy consumption for the whole production chain from grain to ethanol. The analysis has included the energy consumption for cultivation of grain, production of chemicals, the production chain for wood chips, the steam production and the ethanol plant. The grain and wood chips are both considered raw materials there for the energy content in these are not included as energy input in the system.

In this thesis an energy analysis of ethanol production at the ethanol plant of Lantmännen Agroetanol in Norrköping has been performed. The ethanol plant has been studied in combination with Händelöverket, the combined heat and power plant which provides the ethanol process with steam. The purpose of this study was to determine the energy consumption for the whole production chain from grain to ethanol. The analysis has included the energy consumption for cultivation of grain, production of chemicals, the production chain for wood chips, the steam production and the ethanol plant. The grain and wood chips are both considered raw materials there for the energy content in these are not included as energy input in the system.

AbstractThis thesis is the final part of the Innovation and Design Engineering Programme (180 ECTS credits)at the Faculty of Health, Nature and Engineering Science at Karlstad University. The extent of thisthesis is 22.5 ECTS credits and has been performed independently by Hannes Jernberg during thespring of 2013. Metso Paper Karlstad AB is the task maker of this project, and Arvid Johansson is thecompany Representative. Metso Paper Karlstad AB is one of the world leading developer andmanufacturer of tissue paper machines.In the current situation, the company has developed and patented a power management systembased on a Cross Flow Turbine. The current construction is limited to a paper width of 2.9 meters.The company wants to take advantage of all the opportunities provided by the patents, to develop aturbine solution paper machine with a paper width that is wider than 5.5 meters, and give the abilityto manufacture paper for lower energy consumption which is an important part of the production asit is very energy intensive.Problems arise with the increasing length of the turbine, ultimately resulting in that the deflectionbecomes too big and that the momentums, due to the increased torque the turbine blades breaks.By applying the design process, this work has resulted in a number of potential solutions to theproblem.

Most people have been forced to throw away a pot-plant after its death. There are many reasons to the death of a plant, but mainly it?s because its owner forgets it, and therefore fails to water it. The purpose of this project is therefore to develop a product which can prevent this from happening, while the product has to have a low manufacturing cost to be able to compete whit other, similar, products on the market. During the project, a benchmarking has been done to give a clear picture of what the product has to compete with. The directives there are for CE-marking, and which of these who concerns the product has also been looked up.

In several countries that have been early in the development of wind farms, there is today a second hand market for the used wind turbines. The European Union (EU) has established a waste hierarchy in order to minimize throwaway mentality. The second hand market is a part of this as the steps are to minimize, reuse, recycle, extract energy and landfill.In order to promote the development of renewable energy, there are energy certificates for the producers that provide it, wind power being one type of renewable energy. After 15 years the energy certificates for a specific wind turbine are no longer paid, and after that there are several different scenarios for the wind turbine. The scenarios investigated in this bachelor?s thesis are export of the wind turbine to countries that are not as far along as Sweden in their development towards renewable energy, selling in Sweden to individuals, and recycling of the wind turbine, as it mostly consists of metals and therefore is recyclable.

A large number of rivers in northern Sweden have hydropower developments that cause negative effects on both up- and downstream migrations of anadromous species like Atlantic salmon. So far, most attention has focused on the hindrances of adult fish during their upstream spawning migration. However, since turbines in power stations cause losses on downstream passing fish, the focus on negative effects on smolts has increased. The aim of this study was to compare three different causes of losses of salmon smolts passing downstream through a power station area in the flow-controlled River Åbyälven in northern Sweden.A total of 61 wild salmon smolts were caught and radio-tagged in the River Åbyälven during their downstream migration in June 2009. The salmon smolts were released at three locations, 1.1 km upstream from the power station, in the turbine intake and in the upper part of a fishway, acting both for up- and downstream fish passage.

This final thesis contains three major parts, which all have been time demanding:* Designing and construction of a small wind turbine.* Designing and construction of an electrical system.* Thesis with fundamental facts about wind, wind power and design.The thesis contains basic theory in wind power and the energy systems it can be combined with. Different types of wind turbines, which components they consists of and important issues to consider when designing is also mentioned. In the end of this report the technique of our wind turbine will be presented. In the end you can also read about our experiences during the time of designing and construction..

Simulation is a vital tool during development of JAS 39 Gripen, since money and time can be saved.The Auxiliary and Emergency Power System, AEPS, is a subsystem of the secondary power system in Gripen. It has the function of providing the aircraft with electrical and hydraulical power before activation and after deactivation of the main engine. The system also functions as backup in case of a safety critical problem in the main power supply system. The system basically consists of a control unit and an auxiliary gearbox. The gearbox is driven by an air turbine.

AbstractThis report describes our ten week long thesis work which is the last task in our education in mechanical engineering at Linköpings University. The project has been performed at Siemens Industrial Turbomachinery AB?s service department. The company which is located in Finspång produces, sells and provides service for steam and gas turbines around the world.The purpose of this project is to help Siemens develop their maintenance programs for two of the auxiliary systems which are a part of the complete steam turbine system. These are lube and control oil systems.The project is restricted to two of Siemens maintenance products, No Stop Check (NSC) and the annual Safety Inspection (SI).

This study has been carried out at Södra´s 31 local forestry districts and within six plant terminals. The production and sale of seedlings at Södra is managed in collaboration with ?Södra Odlarna?. Approximately 35 million plants are cultivated each year, providing Södra´s members with a wide choice of high quality plants. The seedlings are nurtured at nurseries before transferred to plant terminals where they are stored and watered.