Uvån Hagfors Teknologi AB (UHT) has developed a process ? GRANSHOT® ? for quicksolidification of metals in water baths. In the process liquid metal is splintered ? granulated ?into small drops. The drops are rapidly cooled in a water bath where all the heat energy from theliquid metal is transferred into the water.

At Forsmark nuclear power plant a new course called "education in everyday safety" has been started in an attempt to improve the safety culture. The goal is to spread the of expectations and approach the maintenance management has set, to all employees working at the plants. During the course, theory is mixed with practical tasks to reach a common view how work should be done to achieve safety for the plant and the people that work there.The practical tasks are done inside "maintenance simulators". They are built inside 20 ft containers which contains two dummy pipe systems. On the pipe systems some valves, a flow meter and a pump has been installed.

Rapporten handlar om framtagning av användarvänlig konstruktionslösning till en frekvensstyrd filterkärra och görs på uppdrag av Lars-Olof Larsson vid Filterteknik AB i Karlstad. Kursen är Examensarbete högskoleingenjörsexamen i maskinteknik, MSGC17 vid fakulteten för teknik- och naturvetenskap på Karlstads universitet under vårterminen 2014.I detta examensarbete tas en konstruktionslösning fram till en frekvensstyrd filterkärra som är en blivande produkt och ersättare till två tidigare filterkärror. Filterkärrans uppgift är att filtrera olika oljor från vatten och partiklar. En testkörningsprototyp fanns från början och huvudkomponenterna var utvalda. Genom produktutvecklingsprocessens metodik har ett antal prototyper tagits fram och utifrån det har den med bäst lösning valts och arbetats vidare med. Resultatet blev en kärra med samma ramstomme som tidigare liknade kärror.

To achieve an optimal combustion, an even air/fuel ratio in the combustion chamber is required. An optimal combustion leads to reduced amount of emissions due to a more complete combustion, which is an important matter because of the sharpened environmental laws. This can be attained, among other things, by applying entirely variable cam times. To optimize the engines efficiency and its emissions at all workloads and speeds, an active valve control can be applied. This means that the intake and exhaust-valves can be opened and closed at any time, independent of the crankshaft position.

The thesis investigates if it is possible to replace several pumpimpellers with one controllable pumpimpeller, with a economical and a manufacturing analisys aspect. The studied pumpimpeller is mounted on a midrange wastewaterpump, N3127MT.In the thesis a contemplated manufacturing process is evaluated for a concept that are supposed to act as a controllable pumpimpeller. The pumpimpeller are studied in a manufacturing and flow matter and are presented in the thesis.The manufacturing cost is also estimated, and this has been compared to the storage cost and other costs that the existing pumpimpeller generates.The thesis also shows that the concept has minor losses in cutting quality aswell as the effiency comparing to the existing pumpimpeller.The concept also raises the manufacturing cost and this increasing cost makes the presented concept to expensive to carry through.An investigation of the costs that the existing pumpimpeller produces has also been done, and this shows that there is not that much expenses to earn regarding to for example the storage cost. The storage cost includes information from Flygt?s central storagecenter in Lindas, Sweden and Metz, France, and also an inventory about the pumpimpellers located at Flygt?s different distributors worldwide.The thesis shows that a controllable pumpimpeller will generally increase the cost for the pumpimpeller and the performance of the pumpimpeller will decrease..

This report is the result of a thesis conducted at the consulting firm Bjerking AB andis the final part of the Bachelor Programme in Construction Engineering at Universityof Uppsala. The work aims to investigate the costs and how the choice of ventilationsystem affects building projects during a long-term period. This report covers costssuch as investment, maintenance and energy but also how they affect residents andbuilders. Building regulations for energy consumption are expected to be tougher;therefore a comparison of two different heat recovery ventilation systems(HRV-system) was made. One system is based on a centrally placed unit that coversthe whole buildings ventilation through vertical shafts.

Distillers? grain is a by-product of ethanol production. Corn, wheat and barley are the grains that are generally used in the distillery process. Distillers? grain is rich in protein and phosphorus.

Problem areaAlfa Laval is a world leading company in the heat transfers area and have the vision to continue to be that in the future as well. The company has a lot of press lines where the utilization is high and also has started to become old. Prognosis shows that there is an increased demand of heat exchanger in the future. This increased demand is not something that existing lines will manage. To build new lines cost a lot of money and take time so it is essential that new lines are correct from the start and not need to be rebuilt or a lot of time spent to trim it.GoalThe goal is to achieve 100% theoretical utilization of the press (the press shall press the amount of plates it is designed for).

Understensho?jden is Stockholm's largest eco-village which was built in the early 1990s with the vision of enabling ecological living for people. However the ecovillage is no longer considered as environmentally friendly because of its relatively high energy consumption, and non-updated energy system. The purpose of this study is therefore to investigate how Understensho?jden should reduce their energy consumption and upgrade its energy system by using Blower-Door, IR-camera and Design Builder.

Sedan industrialismens start har människan påverkat klimatbalansen genom förbränning av fossila bränslen. Rökgasemissionerna förorsakade av internationell sjöfart kan inte tillskrivas någon särskild nations ansvar på grund av dess globala och komplicerade verksamhet. FN:s sjöfartsorgan IMO har således åtagit sig ansvaret att minska sjöfartens miljöpåverkan. Införandet av nya miljömål har resulterat i strängare globala och nationella regler som tvingar sjöfartsnäringen till omfattande anpassningar under kort tid. Som lösning för att uppfylla kommande krav gällande rökgasemissioner har flertalet alternativa bränslen diskuterats.

The Goal with this Master of Science thesis is to expand the possible turbine efficiencymeasurements on an exhaust turbocharger. It was done as a part of the CICERO competencecentre. To feed the turbine with air a special flow rig has been used. Instead of loading theturbine by just restricting the compressor flow a docking system for an electrical dynamometer isdesigned to use the dynamometer as an additional loading source. By using an electricaldynamometer as loading device for the turbine, measurements are not depending on compressorperformance.A large part of the work consists in designing accessories for the dynamometer.

This is a report written for an examination project C-level, on the subject of energy. The examination project is a product of the FVB Sweden AB (district heating bureau). It started with a meeting with Stefan Jonsson FVB Sweden AB, were he explained the content of the project, and from this a presentation of the problem was made. The problem that needed to be solved was how they could control the valves in the system to provide heating to everyone in the system. The valves are often oversized so the pump in the heating plant would have to be enormous to be able to provide enough flow to be sufficient, if everyone in the system had there valves fully opened. I came up with two solutions to the problem, one was a wireless network that could keep track of the valves and the other solution was an extra sensor that was placed on the radiator.

Understensho?jden is Stockholm's largest eco-village which was built in the early 1990s with the vision of enabling ecological living for people. However the ecovillage is no longer considered as environmentally friendly because of its relatively high energy consumption, and non-updated energy system. The purpose of this study is therefore to investigate how Understensho?jden should reduce their energy consumption and upgrade its energy system by using Blower-Door, IR-camera and Design Builder.

The importance of energy- and environmental issues has increased, and the work towards reducing carbon dioxide emissions plays a major part. The European Union has set up goals for the membership countries to work towards this to happen. The carbon dioxide emissions in Sweden have been reduced the last few years, but there is still a lot to do. About 30 per cent of Sweden?s carbon dioxide emissions generate from energy usage related to housing, this is why the housing sector is of interest to examine.

EGR (Exhaust Gas Recirculation) är en teknik som används för att minska utsläppen av kväveoxider från förbränningsmotorer. Med EGR återcirkuleras delar av avgaserna till motorn vilket medför att sot och andra partiklar samt sura ämnen återförs. Därmed ställs det nya krav på motorns material och det gäller framförallt motorns cylinderfoder och kolvringar som detta arbete inriktar sig på. Syftet med arbetet är att med hjälp av en nötningsrigg sålla mellan olika material och ytbeläggningar under EGR-liknande förhållanden samt att undersöka olika faktorers inverkan på slitaget. En nötningsrigg av typen pinne-platta används där en del av en kolvring förs fram och tillbaka över en provbit från ett cylinderfoder.