The combustion engines in today?s vehicles are getting more and more advanced and there are increasing demands on that the engines should operate during optimal conditions. Examples of internal combustion engine parameters which may be carefully controlled are the rate between fuel and air, that this gas mixture is homogenous enough and that it is ignited at the correct moment. Moreover, the requirements of these parameters vary depending on, among other, engine speed and load. To meet these requirements in all occurring operation conditions, it is required that many subsystems work together.

Results have shown that flow batteries may be a solution in the future as an effective and environmental friendly method to an energy storage system (ESS). The technology is reliable and has a high efficiency that comes with low energy losses and a long lifetime. The range of possible fields is suitable for cutting energy peaks in the power grid, by always have a ready and available energy storage that balances the production. By comparing the advantages of flow batteries with conventional batteries it is mainly the fact that they can conserve energy for a long time without being self-discharged thanks to that the storage capacity is in principle endless and limited by the size of the electrolytes tanks that makes them a great energy storage system. The batteries won?t take any damage or decrease in performance when charging or discharging it or if you exhausts it to 100 % and leave it discharged for a long time.

Hallin, Dan (2009) Elevens val. En studie av elevers intresse och motiv för valet av gymnasiets Elprogram. (The pupil?s choice. A study of students? interest and motivation for the selection of the electrical program at the upper secondary school). Skolutveckling och ledarskap, 90 hp.

Wavecraft AB develops medical equipment for heating of organic synthesises. The heating is done with microwaves, which improves the process in both speed and accuracy compared to the more traditional methods where heating elements are used. This report discusses the developement of an automatic lid mechanism for one of Wavecraft's product prototypes. The company assumes that the final product will be integrated by customers into fully automated systems, and the upgrade from a manually to an automatically controlled lid is therefore an important step in the product's developement process.The first stage och the project was an idea generation process. The ideas generated here were organized into five different concepts of which the best one was selected through the use of a concept matrix.

This thesis describes redesign and adaption of a products housing. In order to make it more economical to produce at a lower production volume. The thesis is based upon a prototype that a previous student developed for injection moulding. The goal is to find alternative manufacturing methods, but also to identify parameters that affect the cost of the injection moulding tool.The housing must be tough in order to protect the circuit board inside. But at the same time it must allow sound, light an electrical communication to pass through.

Many of todays studies show that district heating is one of the betteralternatives as heating source because of its low environmental load.The energy source is often leftovers from other processes producing energy or waste, like garbage or chips.Electricity in combination with geothermal heating is another heating system that has increased sharply during the last years, and also this system decreases the discharges that have negative affectson the environment compared to several other heating methods.This report aims to, concentrated towards these two different heating systems, estimate the amounts of discharges they indirect cause and how the environment is affected.We have calculated the mean value for discharges of carbon dioxide, nitrogen oxide, sulphur oxide and dust generated from electrical power used in Sweden.Through interviews and research we have gained data for the same substances that district heating based on combustion of garbage and biofuel generates.We have also in cooperation with a housing company chosen a building we see representative for many of the new single-family houses built in Sweden today.Based on its shape and appearance we theoretically created three alternatives of the same house, each of them with climate screens different from each other.Together with the amounts of discharged environmental affecting substances, these houses were the base for our calculations and studies when investigating the different heating sources environmental effect.The results have thereafter been analyzed and discussed from different angles..

This master thesis is a result of the work carried out for Research Electronics at Siljansnäs. The company develops customized electronical systems. Because of the rapidly increasing interest in colour displays there has been a desire within the company to represent information from sensors and electrical systems in a more advanced way.Due to the mentioned reason above we were given the assignment to solve how a colour display using the STN technique works. The technique is used by small displays, the size of QVGA. Our ambition of this diploma work is to develop a fully functionally test prototype to evaluate the LCD (Liquid Crystal Display) and the LCD controller.

This bachelor thesis is about an ultrasonic sensor, implemented in a bubble chamber in Artis. The sensor consists of the piezoelectric sensor and an electronic control circuit. The control circuit consists of a programmable microprocessor, PIC18F2420 and a circuit, which sends the excitation signal to the piezoelectric sensor, and later receives the echo. This bachelor thesis consists also of a theoretical study, which examines different techniques of liquid level sensing in a chamber. The study discusses which factors are important in liquid level sensing and examine accepted methods.

HAFA Bathroom Group has given us the assignment to develop a standardized back panel for their bathroom cabinets. This cabinet is going to be applied to most of their current and future cabinet solutions. To this point, they have constructed unique suspensions-and back panels for most of their cabinet models. They have also been forced to pull wiring and assemble the cabinets differently because of factors like; position of the wall sockets, dimensions of the cabinets and their shapes.The company wants to distance themselves from their current solution, firstly because the cost of having manpower to design each individual suspension solution, secondly because they will save a lot of money when the manufacturing process requires a minimum of components to be constructed. As a result of this, the company can use their resources better to develop future products.The main idea is that the consumer isn?t required to change the suspension or back panel when they decide to buy a new cabinet.

The EU has decided that it should be possible for consumers to get information about the origin of the electricity they buy. Therefore, there is a need to examine different systems for electricity disclosure. In this thesis two ways of disclosure have been studied:? Certificate system. A certificate system involves two parallel markets, one for trading electrical energy and one for trading certificates of origin.? Separated Markets.

The construction process which is used today while constructing residential buildings has for along time remained unchanged. Unfortunately the development process has gone away frombecoming industrialized and instead most of the work is done at the construction site. In thisrespect this is a worse alternative because the project outcome will be more expensive and theconstruction time will be longer. Skanska?s vision is to have a process which is more like the oneused in small residential buildings which is fully industrialized.The constructing process for residential building involves more parties and therefore it becomesmore complicated.

Den senaste trenden inom flygvapenindustrin är utveckling av obemannade farkoster. Den svenska vapenindustrikoncernen Saab AB följer denna trend i och med den stundande introduktionen av företagets obemannade helikopter Skeldar V-150. Som ett led i vidareutvecklingen av detta system finns planer på att även lansera en marin variant, kallad Skeldar M. Tanken med denna marina variant är att möjliggöra fullständigt autonoma starter och landningar från fartyg. För att kunna genomföra detta på ett tryggt sätt även i hårt väder krävs att helikoptern hålls säkrad på fartygsdäcket såväl innan start som efter landning.Uppgiften för detta arbete har varit att ta fram koncept för hur ett sådant säkringssystem skulle kunna se ut.

In Sweden, there are limits to how much leachable substances waste must contain in order to be deposited as hazardous waste. Fly ash from waste incineration often end up over the limit, mainly due to the chloride content. Fly ash is therefore often deposited abroad. The purpose of this study was to investigate the possibility to handle fly ash locally. To clarify how the law is applied, environmental reports and permit documents from ten waste sites with permission to deposit fly ash were studied.

The interest in tiny wireless applications raises the demand for an integrated reference oscillator with the same performance as the macroscopic quartz crystal reference oscillators. The main challenge of the thesis is to prove that it is possible to build a MEMS based oscillator that approaches the accuracy level of existing quartz crystal oscillators. The MEMS resonator samples which Philips provides are measured and an equivalent electrical model is designed for them. This model is used in the simulations of the Pierce oscillator and the transresistance amplifier oscillator that are evaluated in this thesis. Finally the Pierce oscillator is implemented in the A BCD2 process and manufactured at Philips Semiconductors in Nijmegen, The Netherlands.

The use of Power Line Communication, PLC, as a communication solution for Automated Meter Reading, AMR, is popular by utilities in Sweden and other parts of the world due to demands of accurate and fast meter reading. However the use of the electrical grid as a communication medium is complex and sometimes problematic. This report handles some of the issues and problems that are important to understand when using the grid as a communications medium. Focus is mainly on investigating high frequency distortion in the Kristianstad power grid own by C4energi caused by a frequency converter. Measurements on site are done to investigate signal damping in the grid, different configurations for the frequency converter and signal strength of the PLC-system.