Volvo Motor AB i Skövde tillverkar motorer till Volvos personbilar. Tillverkningen av motorerna är till stora delar automatiserad. Den planerade produktionsökningen kräver att monteringsfabrikens kapacitet ökas från 370 000 till 450 000 stycken motorer per år, vilket dagens monteringssystem inte klarar av.Dagens monteringssystem för yttre komponenter är uppdelad i ett antal monteringsmoduler. Tack vare hög flexibilitet klarar monteringsmodulerna att hantera både 4-, 5-, och 6-cylindriga motorer. Volvo Processutvekling Skövde arbetar med att ta fram ett monteringssystem med erforderlig kapacitet.

In Sweden, there are limits to how much leachable substances waste must contain in order to be deposited as hazardous waste. Fly ash from waste incineration often end up over the limit, mainly due to the chloride content. Fly ash is therefore often deposited abroad. The purpose of this study was to investigate the possibility to handle fly ash locally. To clarify how the law is applied, environmental reports and permit documents from ten waste sites with permission to deposit fly ash were studied.

The purpose of this study was to examine how teachers practice Arne Tragetons theory of using computers as the first writing instrument in reading and writing development. We wanted to clarify how the work from using Tragetons theory was applied while investigating if and how other methods of reading and writing instruction were used. Our interest lays in how the teachers accomplished the knowledge of this theory and also how the choice of this approach came about. To investigate this we used interviews with a qualitative nature, where seven active teachers were interviewed. They worked in three different schools in years one to three, they were all women and had various long experiences of work on the computer writing tools.

The interest in tiny wireless applications raises the demand for an integrated reference oscillator with the same performance as the macroscopic quartz crystal reference oscillators. The main challenge of the thesis is to prove that it is possible to build a MEMS based oscillator that approaches the accuracy level of existing quartz crystal oscillators. The MEMS resonator samples which Philips provides are measured and an equivalent electrical model is designed for them. This model is used in the simulations of the Pierce oscillator and the transresistance amplifier oscillator that are evaluated in this thesis. Finally the Pierce oscillator is implemented in the A BCD2 process and manufactured at Philips Semiconductors in Nijmegen, The Netherlands.

Uppsatsen är en litteraturstudie som syftar till att definiera begreppet dyspraxi och kartlägga de faktorer som ger upphov till dyspraktiska svårigheter. I arbetet framgår hur svårigheterna manifesteras i individens vardag samt hur man på bästa sätt kan möta och stödja individer med dyspraxi. Det som framkommit av vår studie är att dyspraxibegreppet är ett mångfacetterat begrepp med olika definitioner beroende på i vilket land man befinner sig. Det är i hjärnan och nervsystemet man kan finna de bakomliggande faktorer som ger upphov till svårigheter i främst tre specifika områden nämligen: perception, motorik och sensorisk integrering. Det har visat sig att det neuropedagogiska synsättet är ett ypperligt sätt att se på individens svårigheter men även att lyfta fram individens starka sidor och potentiella utvecklingsmöjligheter.

To enable the enhancement of the driver's environment in a forklift, an alternative form of steering has been evaluated. An earlier concept with a combined driving and steering wheel has been exchanged to a concept with two driving wheels. A link wheel has replaced the combined driving and steering wheel. The steering is done through differentiation of the velocities of the two driving wheels. The scope of this master thesis is to create a simulation model, create a control program and to evaluate the concept of two driving wheels.

Pupils learn in different ways, varied teaching is needed to encourage all pupils. Aesthetic can be a good tool in this work and dance is one of the aesthetic subjects that can be used in the education. Dance gives the pupils an awareness of their bodies and what they can express through it. The essay discusses diffrent angel of incidence of dance in school and its positive effects and examines what kinds of dance there are in the schools of Vänersborg?s municipal.

För att utöka ett fordons användningsområde kan det utrustas med olika typer av arbetsredskap och lasthanteringsutrustning. För att driva dessa finns möjlighet till kraftuttag (PTO - Power Take-Off) från ett antal anslutningar vid motor och drivlina. I dagsläget saknar motorns styrsystem information om dessa laster vilket kan påverka styrningen negativt. I detta arbete presenteras en metod för att estimera det okända lastmomentet på kraftuttaget. Metoden utgår från Newtons andra lag för svänghjulet och det drivande momentet till drivlinan beskrivs av en dynamisk modell.

People are usually directed towards each other in conversations, to make it easier to hear what is being said. Algorithms for voice and speech recognition works in a similar way, regarding the microphone direction towards the sound source. In this thesis in electronics has therefore a servo control with binaural sound localization been implemented on a microcontroller connected to two microphones.When people perceive sound, the brain can estimate the sound source direction by comparing the time taken by the sound reaching one ear to the other [1]. The difference in time is called the interaural time difference, and can be calculated using various techniques. An exploratory comparison between the techniques cross-correlation and cross-spectrum analysis was carried out before implementation.

The use of Power Line Communication, PLC, as a communication solution for Automated Meter Reading, AMR, is popular by utilities in Sweden and other parts of the world due to demands of accurate and fast meter reading. However the use of the electrical grid as a communication medium is complex and sometimes problematic. This report handles some of the issues and problems that are important to understand when using the grid as a communications medium. Focus is mainly on investigating high frequency distortion in the Kristianstad power grid own by C4energi caused by a frequency converter. Measurements on site are done to investigate signal damping in the grid, different configurations for the frequency converter and signal strength of the PLC-system.

Ramsta Robotics är ett företag som ligger i Uppsala. Företaget grundades 1999 av tre uppfinnare. Man har utvecklat en robot, som används för att göra rent i djurstallar. Tvättarbetet har hittills gjorts helt manuellt med högtryckstvätt. I framför allt svinhus ärarbetsmiljön direkt hälsovådlig ? bland annat på grund av alla de kväveföreningar som löses ut när vattnet blöter upp anläggningen.

AbstractThe future of ethanol is depending on good solutions for the production. ENA energy power plant produces electrical power and district heating by heating biofuel. By building an integrated bioenergy plant surplus steam could be used to produce ethanol as fuel to vehicle.This would mean that ethanol is produced renewable energy and the energy for the process derives from the surplus of power.  ENA energy, MDH (the University of Mälardalen) and the energy authority has initiated a research project were different bioenergy combinations integrate with existing power plant.  As a part of the project which size an integrated factory should be to gain the best efficiency for the plant was investigated. Consideration will be taken to the cost of the production in order to be competitive to the price of imported ethanol.  Etanolens framtid vilar på bra lösningar för framställning.  I ENA energi kraftverk i Enköping produceras el och fjärrvärme genom eldning av biobränsle.  Genom att bygga ett integrerat bioenergikraftverk där skulle man kunna använda överskottsånga till att framställa etanol som fordonsbränsle.

The use of Power Line Communication, PLC, as a communication solution for Automated Meter Reading, AMR, is popular by utilities in Sweden and other parts of the world due to demands of accurate and fast meter reading. However the use of the electrical grid as a communication medium is complex and sometimes problematic. This report handles some of the issues and problems that are important to understand when using the grid as a communications medium. Focus is mainly on investigating high frequency distortion in the Kristianstad power grid own by C4energi caused by a frequency converter. Measurements on site are done to investigate signal damping in the grid, different configurations for the frequency converter and signal strength of the PLC-system.

The use of Power Line Communication, PLC, as a communication solution for Automated Meter Reading, AMR, is popular by utilities in Sweden and other parts of the world due to demands of accurate and fast meter reading. However the use of the electrical grid as a communication medium is complex and sometimes problematic. This report handles some of the issues and problems that are important to understand when using the grid as a communications medium. Focus is mainly on investigating high frequency distortion in the Kristianstad power grid own by C4energi caused by a frequency converter. Measurements on site are done to investigate signal damping in the grid, different configurations for the frequency converter and signal strength of the PLC-system.

The use of Power Line Communication, PLC, as a communication solution for Automated Meter Reading, AMR, is popular by utilities in Sweden and other parts of the world due to demands of accurate and fast meter reading. However the use of the electrical grid as a communication medium is complex and sometimes problematic. This report handles some of the issues and problems that are important to understand when using the grid as a communications medium. Focus is mainly on investigating high frequency distortion in the Kristianstad power grid own by C4energi caused by a frequency converter. Measurements on site are done to investigate signal damping in the grid, different configurations for the frequency converter and signal strength of the PLC-system.