Tomo Hugglink (TOMO Skog) is an innovation for harvest and transport of biofuels. The system consists of a truck, a chipping unit and crane mounted on a link and a wood chip trailer. The system works in such a way that the chipping unit is disconnected and placed on the site and wood chips are loaded directly into the wood chip trailer.The aim of this study was:- To examine the performance of the TOMO Hugglink system under different conditions such as the size, placement and quality of the pile.- To calculate the cost per raw ton for two vehicle combinations at different transport distances and to examine the effect of a reduction in set-up time and an increase in load weight.- To identify possible improvements with the TOMO Hugglink system.A time study was conducted within the thesis work to make it possible to determine production and time consumption. In the subsequent economic analysis the cost per tone at different transport distances was calculated for two different lorry concepts. Furthermore the effect of a reduction in set-up time and an increase in load weight was calculated.Under current conditions the utilization of the chipper is low and only 29 % of the total system time is occupied by chipping.

Makrocykliska laktoner har varit flitigt använda avmaskningsmedel hos olika djurslag sedan mitten av 1980-talet och används fortfarande. För att avmaskningsmedel ska vara så effektiva som möjligt är det viktigt att veta hur de tas upp och omsätts i kroppen hos olika djurarter. Detta för att kunna anpassa doseringen till olika djurslag. Några farmakokinetiska parametrar har undersökts för att se om det förekommer skillnader i upptag, distribution, metabolism och utsöndring mellan nötkreatur, får och gris. Genom att jämföra olika studier fann jag skillnader i halveringstid, AUC, Cmax och tmax mellan gris, nötkreatur och får.

Title: The component approach - From the harmonization process as a background to the perception of benefits and costs as effects.Authors: Elin Börjesson & Emma KarlssonTutor: Titti EliassonKey concept: Harmonization, Component approach and Benefit/CostBackground: With IFRS for SME's as a basis, the Accounting Board developed K3 which shall apply from financial year 2014. Upon introduction of the K3 companies will be forced to apply the component approach. When K3 with the associated component approach went out for consultation it resulted in a debate where some actors opposed the imposition of a requirement and not an option. It was questioned whether the costs with the component approach would be greater than the benefit of the implementation.Formulation of the problem: How is the introduction and use of the component approach seen by different operators from a benefit-, cost perspective?Aim: The aim of this essay is find out how the introduction and use of the component approach is seen by different operators from a benefit-, cost perspective.

With the elevated oil prices of today it is necessary to look for other heating alternatives. If the oil price continues to develop in the same way it has done the last years it will soon be impossible for many producing garden companies to survive. The purpose of this diploma work is to compare three different fuel options in order to find the most economic one considering the conditions of Katrinebergs Handelsträdgård AB. In relation to oil it is profitable to change to any of the three alternatives: wood chips, wood pellets and grain. The most profitable option is to change to wood chips. This alternative has a payoff time less than three years and after that the annual saving compared to the oil is relatively high. The annual cost is 65 % of the cost of the oil alternative.

Since 1996 the Swedish households have ten folded their volume of loans for own homes that is attached to a floating interest rate. Also in 1996 the Swedish electric market was deregulated. These two facts have increased the volatility in the household expenses for these two commodities. This thesis studies the risk for homeowners attached to the exposure against the electric and the credit market. The risk model used is Cost-at-Risk which is usually used by public authorities for analysing the risk involved with national debt.

As IT service departments in organisations are becoming more complex and customised, the indirect costs are increasing in relation to the total costs. The difficulty of fully estimating and identifying the spread of the cost in the IT service department is increasing. As a result, firms tend to budget the business unit as a total cost rather than as a spread of defined costs. In order to deal with this challenge an ABC calculation will be applied. The Time Driven ABC model will be conducted in OMX´s Servicedesk unit within the IT services.

Syftet med studien var att undersöka huruvida utsattheten för ?sunk cost-effect? och förankringseffekten ökade vid intuitivt processande jämfört med analytiskt processande. Deltagarna i studien var 78 studedenter vid psykologiska institutionen vid Göteborgs Universitet. Datainsamlingen gjordes genom en pappersenkät. En 2 × 2 - vägs ANOVA avseende bias och process gjordes för både ?sunk cost effect? och förankringseffekten i en mellanindividdesign.

An important process for grid companies in order to reduce power losses in electricity distribution grids is to figure out where and how they appear. This report describes the factors that cause power losses in low voltage distribution grids and methods for how they could be measured and analyzed. Measurement data for consumed and injected energy were collected for twelve low voltage distribution grids owned by Gävle Energi AB in order to analyze the size of the power losses and how the measurement uncertainty affects the collected data. Then models of three of the grids were created in MATLAB in order to analyze the data and the power losses were calculated to be compared to the collected data. Curve fitting were also used as a method in order to analyze the power losses from collected data.The results show that the losses in the studied grids are low.

Sweden?s District councils and Country councils are in itself to a large extent responsible for the state financed welfare. Because of this, Sweden has a contribution- and adjustment system. The reason for this system is to create equal chance, for all District councils and Country councils, to be able to give the citizens service independently of their income and non-influential structural differences. The adjustment is built upon the so-called standard cost method, which contains four different parts.

Problemformulering: Små företag kan ha svårt att slå sig in på en marknad på grund av en begränsad marknadsföringsbudget och konkurrens från andra aktörer. Dessa företag måste därför i många fall använda andra mindre kostsamma metoder än traditionell marknadsföring för att etablera sig på en marknad.Syfte: Att undersöka hur ett mindre företag kan etablera sig på en marknad genom användandet av andra marknadsföringsstrategier än traditionell reklam. För att besvara vårt syfte två delar ur 4 P undersökts, plats och påverkan (distribution och marknadskommunikation).Metod: En fallstudie har gjorts av företaget Gooh där fyra personer på Gooh har intervjuats genom semi-strukturerade intervjuer.Analys: Gooh har gått från en exklusiv distribution till en mer intensiv distribution för att nå ut till fler kunder och konsumenter. I sin marknadskommunikation har Gooh använt sig av olika aktiviteter som viral och buzz marketing för att generera word-of- mouth både bland konsumenter och kunder.Resultat: Gooh har ökat omfattningen av distributionen samtidigt som de ökat omfattningen av marknadskommunikationen för att nå ut till fler kunder och konsumenter och etablera sig på marknaden för färdigmat.Slutsats: Gooh har använt sig av en kombination av distribution och marknadskommunikation i sin marknadsföring och genom detta fått ett stort antal kunder och konsumenter och därmed etablerat sig på marknaden genom icke- traditionell marknadsföring..

Bakgrund och problem: Anva?ndningen av e-handel har va?xt de senaste a?ren och detta har medfo?rt sto?rre mo?jligheter fo?r kunder. E-handeln har mo?jlighet att na? ut till en sto?rre ma?lgrupp utan geografiska hinder. Detta medfo?r ett behov av fo?ra?ndring i distributionen av fysiska produkter.

AbstractThe assignment were assigned by Camatec Industriteknik AB. Camatec is a Karlstadlocated consulting company, they make everything from pilot studies to complete projects in mechanical design and calculation. They even have their own patented product, Camcoil. It is a winder for steel strips and is used for example with hardening of the steel strip. The assignment has been to solve the problems encountered by some customers within this product.

The market for biofuels from the forests have had a positive development and the job initiators for this master´s thesis wanted to examine the profitability of a method for harvesting forest fuel, which was unfamiliar to them. The method was the ?long tree tops-method?, here called the LT-method. The LT-method is characterised by the fact that timber is harvested as the only roundwood assortment while the rest of the stem, which in other cases would become pulpwood, is harvested as forest fuel together with the logging residues. The method is based on the assumption that advantages in handling of the forest fuel assortment such as increased load weights for forest hauling and truck transportation, should compensate for the lower price for pulpwood when sold as forest fuel. The aim of the study was to compare the profitability of the LT-method with the GROT-method (harvest of timber, pulpwood and logging residues) and conventional logging without any harvest of forest fuel, and aslo to try to identify factors affecting the profitability of the different methods.

In 2013 a new emission standard for heavy trucks was introduced and hence a number of new parts was brought in to Scania CV AB. This created a need for modifications in the silencers flow. The flow is highly complex involving several suppliers, call off methods and different models of silencers. The aim for this project was to improve the existing silencers flow. The flow, from supplier to assembling, has therefore been mapped.

This paper is the result of a case study conducted at Uppåkra Mekaniska AB during the spring of 2006. The task that was presented by Uppåkra was to develop a basis for a decision for the planning activities at the company, so that in the future they can create lot-sizes which are based upon a total cost perspective. Total cost in regards to lot-sizing is defined as the sum of the administrative reordering costs and warehousing cost per stock keeping unit.To collect data a series of interviews and observations were conducted. This data was then used during the lot-sizing simulation and analysis. The 15 units that the simulation was conducted on were grouped into three item classes depending how many different machine setups they required during the production process.