The control of indoor temperature must be able to handle large time constants and both measureable disturbances like outdoor temperature, and non-measurable disturbances, like waste heat from appliances. Due to cheaper microcontrollers (small computers with designated tasks) with better performance, more advanced and computation-demanding methods for control can be used.In this thesis, Generalized Predictive Control (GPC) has been implemented and tested on a theoretically derived model of a house. GPC states that a model of the system is estimated in every sample, and the control is carried out simultaneously, based on predictions of the model. Disturbances like solar radiation can be estimated and used in the control as well. The control signals are determined by quadratic programming, which makes it possible to consider conditions, for example limitations on the control signals.GPC requires a number of parameters to be defined, like model order and control signal penalty, but is relatively robust for variations in them.

By the year of 2007, 97 % of all listed companies in Europe had a CSR strategy described on their website. As the concept of CSR during the last decades has increased rapidly in popularity, a need to understand how such a strategy can be implemented has followed. While working with CSR in an integrated manner shows similarities to other popular management ideas, such as Lean and TQM, companies applying to a CSR strategy has been shown to be under higher scrutiny from media and NGO:s. Through a case study this thesis examines how these special circumstances of a CSR strategy makes The Body Shop use organizational control to avoid being subject to scandals due to not fulfilling the promises made to its customers. The results show that The Body Shop's commitment to CSR creates a need for a stringent bureaucratic Control system that highly restricts the freedom of action for its employees.

Svenska Kraftnät is (together with the other transmission system operators of the Nordic power system) responsible for keeping balance between the generated and demanded power in the Nordic power system. Spontaneous load variations and system disturbances, however, lead to power imbalance followed by frequency variations. The frequency deviations can be limited to an acceptable level by the spinning reserve, mainly by hydro power control. But there are also other system properties which have a great influence on the frequency and system stability. The frequency and voltage dependence of the loads have a direct influence on the power balance.

Humans and dogs are both mammals. One of the differences between the two species is that man walk on two legs and dogs on four legs. There are also differences in the nerve system between the two species. The human nerve system is supposed to provide opportunity for fine motor tasks- while the nerve system of the dog is more focused on the ability to perform locomotor tasks. Humans need to increase their motor control and postural control when affected by various conditions and diseases.

Franchise theorists have to a large extent failed to keep up with the actual development in global franchise chains. The recent emergence of fast growing multi-unit-franchisees has fundamentally been ignored, and it has been claimed that the new phenomenon can be regarded as a mere replication of the franchisors? structure and Control system into sub hierarchies. This study however, suggests that the reality is more complex. Through conducting case studies of two Nordic multi-unit-franchisees, new theories are built explaining how and why Control systems are designed the way they are.

In the present thesis, we have studied the management Control system in Enskede-Årsta-Vantör, one of Stockholm?s municipal districts, with focus on theories about New Public Management (NPM). When NPM was introduced, a number of complications arose. Some of these, along with the district?s solutions of the complications, are described and analyzed using e.g.

This master thesis deals with problems in the arc length control in Pulsed MIG/MAG Welding. The main problem is that it is not possible to measure the arc length. In the present solution the voltage over both the electrode and the arc represents the arc length. To improve the arc length control a model of the electrode melting has been built. One output from the model is the voltage over the electrode and with this voltage together with the measured voltage it is possible to calculate the voltage over just the arc.

The purpose of this thesis is to find means of control that secure cost efficiency regarding the accommodation for the employees on missions abroad of the Swedish Ministry for Foreign Affairs. Today the ministry?s cost for the employees? rented housing is 100 million SEK and there is a need of improvement in the control of these costs. A work method for organizational development will be used in order to reach the findings presented in the thesis. First we study the strengths and weaknesses in today?s Control system.

The purpose of this thesis is to analyze the design and function of an engine production management?s Control system and its intended function, and to contrast it with the present management Control systems in use on an operational level. Interviews conducted with employees from all levels of the engine production are the main source of this study?s empirical foundation. Information has also been gathered from relevant written material such as annual reports, internal documents etc.

When traffic in large cities increases, it becomes more vulnerable to disturbances such as accidents, stalled vehicles or construction; therefore, traffic jams are more likely to occur. For better control of the traffic at a disturbance the Swedish National Road Administration (SNRA) has traffic equipment which can be controlled from a command centre. This traffic equipment consists of gates and signs with variable messages. This report will discuss the system used for traffic control in Stockholm. It will present proposals designed to improve it.

The aim of this paper is to examine how the design of management control in a retail trade company affects motivation among its employees. Our purpose is to identify what actions create motivation and how management can benefit by developing and promoting such activity from its high-performing employees. Motivated personnel have become increasingly important in companies today, and companies are increasingly reliant on individual employees? capabilities. The study covers all parts of the management Control system, to see how these align to create goal congruence in an organizational context.

This master thesis is made of two parts. The first part concerns the method and results ofdesigning a motion Control system for a piece of research-equipment called BIRGIT. Theequipment is made to be used for research on eyemovements. In the second part, a computermodel of a part of the balance organ in the inner-ear is developed. The work has been done atthe Bernadotte laboratory at S:t Erik Eye Hospital.The equipment the Control system is made for is a so-called rotationchair.

Today the competition in the automobile industry is getting all tougher. The technology behind cars becomes more advanced. To get ahead of competitors car companies has to look into new areas of innovation.One important area is vehicle safety. Bigger companies have come so far in vehicle safety that difference between cars more depends on the car type (size) than the technology behind it.There is one area where vehicle safety that still has great opportunities for improvement, which is in active safety. The term active safety states that the car has the ability to identify treats and automatically respond to the treats.

In this report a system for Rapid Control Prototyping, RCP, is evaluated through animplementation of the motor control methods Field Oriented Control, FOC, and Space VectorPulse Width Modulation, SVPWM. The evaluation emphasizes on time-consumption andresource utilization on the used hardware and on usability for of software.A new mechatronic laboratory is under development at ABB Corporate Research in Västerås. Itwill be used for both mechanical and motion control design using existing and new hardware.The control structure in a traditional robot system will be interfaced to a rapid prototypingsystem which should allow easy changes to algorithms at different levels in the system.The system designated for this project comes from National Instruments and constitutesLabVIEW Real-time and FPGA module as the software tools. The hardware is a NI Single-Board RIO (Reconfigurable Input Output), sbRIO, development board including a Field-Programmable Gate Array, FPGA, from Xilinx and a microprocessor from FreescaleSemiconductor. Graphical programming is performed in the LabVIEW environment, andthrough Xilinx tools the LabVIEW FPGA code is compiled to VHDL code.A pre-study was carried out to clarify the concept of RCP and investigate different systems forRCP and their traits.

Problem discussion: That empowerment and autonomy can lead to desirable effects on employees is clear. Previous research has found correlations between empowerment and e.g. motivation, job satisfaction, productivity, loyalty and commitment. However, a control problem arises when employees have more freedom in decision-making which could potentially lead to undesirable outcomes. It thus becomes a type of dilemma for management and managers where you have to try to balance a restrictive use of the Control system (to maintain control) and an enabling use (to promote empowerment).Purpose: The purpose of this study is therefore to identify how a company can use its Control system in order to achieve empowerment while maintaining acceptable levels of control.