Laminitis is a debilitating disease causing much suffering to horses and ponies all over the world. It is manifested in the hooves as a mechanical failure of the suspensory apparatus between the hoof capsule and the distal phalanx. Due to the weight of the horse the disease may result in a dislocation of third phalanx. Six healthy standardbred trotters were used in this study on whether standardbreds tolerate forced recumbency as well as Shetland ponies. Recumbency was induced pharmacologically but maintained only by lowering the ceiling height of the box to a height of approximately 125 ? 140 % of the horse´s thoracic height.

In this project we have used the theory of analytical mechanics to derive equations of motion for complex mechanical systems in order to study their behaviour over time. Even if the theory provides powerful tools to tackle tough problems which would be very hard to solve by methods of Newtonian mechanics, you are still relatively limited without running any computer simulations. One realises that in a faster rate it will be an incredibly difficult task to find an analytical solution when the degrees of freedom increases. Even if one would succeed to derive the equations, one still has to solve them to get the information of the systems behavior. Of experience one knows that the equations in general are nonlinear and hence must be integrated numericaly.

sustainable development by reducing the energy use by EU:s directive of energy efficiency and the UN Convention. The second purpose is to present the technical solutions regarding ventilation and heating system that is being used in passive houses. This was done using 8 passive houses, 4 germany and 4 swedish passive houses. Even the international and Swedish system requirements for passive houses have been addressed in this project. The goal was also to explain how and why the mechanical system in passive houses has developed to the technology used today.

Detta examensarbete har utförts i samarbete med Svedala Compaction Equipment AB. Examensarbetets primära mål var att reducera höjden på ROPS tillhörande asfaltvält CC 422. En sänkning medför ett friare vägval och billigare transporter. Hittills har vägvalet påverkats av broar, viadukter och andra hinder. Med hjälp av riktlinjer från Svedala Compaction Equipment AB och Fredy Olssons modell för integrerad produktutveckling togs kriterier fram, vilka användes vid bedömning av olika lösningsförslag. Utvärderingen resulterade i att två av de tio ursprungliga förslagen gick vidare till nästa steg i produktutvecklingsprocessen - primärkonstruktion. Primärkonstruktionen inleddes med vidareutveckling av de två principförslagen.

The objective of this work was to introduce measures to reduce energy and water demand at Gävle Söder 17:10. To succeed, this energy audit has been made. The work is based on collected statistics from the property owner Norrporten, measurements, literature review and through consultation with experts in the field. Two models, one for each building, have been created in the simulation program BV2 to estimate the potential of energy measures based on the collected information. The models in BV2 have been verified against the statistics of the energy consumption.With the help of calculations and simulations, seven cost-effective measures have been identified.

Muntlig kommunikation kan vara begränsad eller omöjlig när patienten är intuberad vid respiratorbehandling. Intuberingen hindrar talet och detta kan vara frustrerande för många patienter. Syftet med studien var att belysa hur intuberade intensivvårdspatienter upplever kommunikation. För att genomföra studien valdes systematisk litteraturstudie som metod. Resultatet baseras på 11 artiklar.

This bachelor?s degree thesis was conducted in mechanical engineering at Halmstad University during spring semester 2010 in close collaboration with the company Gremo AB, located in Ätran, Sweden. Gremo AB produces, developes and sales forest machines in both Sweden and on the international market.Gremo AB belongs to one of the market leaders in forest industry, especially with their forwarder. In order to become a market leader even with their harvester, the company decided to change the harvester to have a swivel and a leveling driver cabin.The aim with this bachelor?s degree thesis was to develop a design concept for the harvester driver cabin, which Gremo AB can apply on the new harvester.

The aim with this study was to investigate the effects a change of manufacturing process would have on the mechanical properties of drill bits made of a WC/Co composite used for stone cutting. The method used today is sintering, where the material is heated in a conventional sintering oven. The other method was microwave sintering, where the material is heated by radiation in the microwave region. Also an investigation of the manufacturing cost were made.The main difference between the two heating methods is that the conventional way is a rather slow process and the microwave method is very fast. The material is also heated homogeniously in the method with mirowaves, aposed to the case with the conventional sintering where the material is heated from the outside in.This makes the material harder and more wear resistent.

It is important that the current urine separating systems are evaluated to allow improvements to be made and consequently increase their future propagation. In order to increase the knowledge about urine separating systems this study was made. It included, among other things, measurements of amounts of urine as well as of the composition of urine collected at Nytorgsgatan 4 in the city of Hallsberg. The study was increased after an inquiry that also included the district of Understenshöjden in the city of Stockholm. In the inquiry, the users were asked questions about odour, cleaning of toilets and occurrence of blockages in the urine water locks etc.

This bachelor?s degree thesis was conducted in mechanical engineering at Halmstad University during spring semester 2010 in close collaboration with the company Gremo AB, located in Ätran, Sweden. Gremo AB produces, developes and sales forest machines in both Sweden and on the international market.Gremo AB belongs to one of the market leaders in forest industry, especially with their forwarder. In order to become a market leader even with their harvester, the company decided to change the harvester to have a swivel and a leveling driver cabin.The aim with this bachelor?s degree thesis was to develop a design concept for the harvester driver cabin, which Gremo AB can apply on the new harvester.

Atlas Copco Tools develops and manufactures handheld industrial tools. Heat and surface treatments are used to provide the tools with certain properties. There are no routines for the choice of treatment or for how to specify treatment on drawings. Production documents that are sent for production abroad may not be clear enough. Some treatments are known as trademarks and there are no instructions for how to specify these on drawings and in CAD-models.The purpose of this master thesis work is to create recommendations for the procedure of choosing heat and surface treatment.

System Andersson AB is a company located in Jönköping that works with developing computer systems for the mechanical engineering industry. As of today, when this report is written, the company is working on the development of a new Manufacturing Planning and Control (MPC) system. This new system aims to create not only a user friendly interface but also a modern, stylish interface. To achieve this, the company has decided to work with a, for them, new application framework; Windows Presentation Foundation (WPF).System Andersson is well known for developing systems for different kinds of touch screens, this project is no exception. For this new user interface the company wishes to implement different types of Drag&Drop functionality.

The calf extrator?s function has been studied, through measuring traction and how this varies in different situations, in comparison with corresponding manual traction situations. This was done against the background that excessive force at assisted calvings at dystocia can mean life threatening damages on the calf such as grave acidosis, vertebral fractures, femur fractures and rib fractures. The calf extractor has earlier been measured to pull with greater force than the established maximum force of ?two strong men?.

Ground construction has to a large extent been dominated by traditional meth-ods during the last 50 years. Although the construction has been changed meanwhile innovations are not accepted. In collaboration with NCC Ltd Region South, I have examined a modern con-struction methodology that has been developed by NCC for future large pro-jects. The method is divided into two central phases. Phase 1 is? Single Pro-duction? which is a preliminary period for ground constructions to come.

Detta examensarbete behandlar vidareutveckling av en treaxlig släpkärra med automatkassettfunktion. Arbetet har utförts hos Släp & LastbilsPåbyggnationer i Övertorneå AB (SLP). SLP är en mekaniskverkstad som tillverkar släp och lastbilspåbyggnationer i Övertorneå. De volymmässigt stora produkterna är släp och lastbilspåbyggnationer för grus, berg och asfalt transporter. Uppdraget är att förse en släpkärra med ett automatkassettsystem.