The aim of this report was to investigate the hypothesis that Norway spruce (Picea abies L. Karst), planted on poor ?Scots pine? stands will not have sustained growth during the whole rotation, due to water deficit in the closed stands. In order to investigate this hypothesis, data from 10 Norway spruce stands in southern-eastern Sweden were collected. In 10 plots in each stand, diameter and breast heights were measured on every tree.

Stands where pre commercial thinning has been ignored or inadequate often tend to have high stem density and low average diameter when they reach heights of thinning. In such stands, it can often be expensive to do a conventional pulpwood harvest as a first thinning. This study investigates the development of the stands and the economic outcome of forest fuel extraction, or a combined harvest as alternatives to the ordinary pulpwood harvest. Simulations in Heureka StandWise were performed for two thin and dense stands, which were constructed by data from the Swedish National Forest Inventory. The simulations show that the extraction of forest fuel in first thinning at an early stage can provide higher net revenue compared to conventional pulpwood harvest at the same time or later.

SUMMARY Several studies have shown that weaning pigs are in great need of heat. The reason for this is mainly because the pigs are given very little feed just after weaning. Some of the pig producers of today have tried to get along with these problems by building some kind of hut for the pigs. Some of these pig houses have been included in this study.The study has shown shortcoming functions for the pig cottage. The expected heat increase has not occurred.

Tropical rain forests only cover around six percent of the world?s land area and contain around 70 % of the world´s animals and plants. Tropical rainforests have been, and still are, negatively affected by human activities. These activities lead to forest degradation which has negative impacts on production and biodiversity. Between 1970-1980 forests in Borneo, Sabah, Malaysia, was subjected to intense logging.

This work is a study in how I as a designer can create the conditions for people to work, socializing and refreshments at one place. A place that encourages creativity, where I made a suggestion at a community table designed for Urban Deli?s new business. By visiting various similar sites I have identified what I think is important in an environment like this and then gave an answer to it in a visual form.A cafe-office will draw lots of different people. Which guests come here to work? Residents, freelancers, but also those who may want surrounded by a new creative work place and maybe leave their regular offices for a day at Urban Deli.

To make it easier for forestry planning the forest owners needs data which describe characteristics of the forest. Such data you usually get from some type of inventory. A relatively new technology which probably is getting more important in the future, is laser scanning because of lower costs. But because the laser technology is relatively new you need to compare it with conventional inventory technologies to get better understanding of the possibilities the laser technology gives. This work intends to estimate field measured characteristics of the forest from laser data with help of regression analysis and then see which of the field measured properties that best could be estimated and which laser variables that gave the best results. This study shows that heights has the best estimates, but biomass, diameter and volume also gives good estimates.

It has been shown that moose can affect plant community composition and structure. Selective browsing with other damages of large herbivores on tree species with different tolerance to disturbance could reshape the tree layer in both managed and natural forests. Rowan Sorbus aucuparia is widely distributed throughout Sweden and Europe. Research has shown that browsing by moose may prevent rowan from reaching browsing safe heights. The goal has been formulated that, where rowan is indigenous, it should have a good competition status and be able to reach tree level.

This diploma work has been carried out in collaboration with the building contractor Sh Bygg Fastighetsutveckling AB in Uppsala with the intention to investigate how the height of a building affects various energy aspects such as transmission losses, infiltration, and the specific energy usage. Three different reference objects have been studied. The reference objects have been simulated for four different heights in the calculation program VIP-Energy.The results show that an increase in floor number can lead to both advantages and disadvantages. As the number of floors increases, transmission losses per square meter floor area decreases. However, as the height of the building increases, the reduction rate decreases.

Saproxylic lichens in managed forests have less substrate available than in unmanaged forests due to the shortage of dead wood. However, a suitable substrate for these lichens could be dead branches on living trees. To this date, there has not been any systematically collected data about theabundance of dead branches on living trees and the lichens growing on these branches in managed forests. The aim of this study was to see where dead branches were located on living trees of Pinus sylvestris and Picea abies, how large the surface area of these branches was and what lichens grewof wood on these branches. The study was made in Finspång, Sweden, where 11 forest stands of P.sylvestris and P.

This thesis assignment at C-level is focused on calculation models and prediction methodswhish can be used in the stage we call ?prospecting? of possible windmill locations. Thelocation is southeast of Halmstad at the Farm ?Stjernarpsgods?. The rapport has two mainareas directed towards this task.

Flooding events are no longer rare, floods occur all over the world. Accordingly, it is vital for the society and different authorities to work with flood mapping. To meet the goal of Uppsala kommun to map the risks of floods in Uppsala län, a map of the different areas around Funboån which are inside the area of risk for flooding have been developed.In the work, cross sections and the water flow have been measured. Moreover, an echo-sounding have been carried out in Funboån to map the bottom topography. From the bottom map and laser scanned data covering the study area, a terrain model was created.

This essay is about the hamlets´ older boundaries, i.e. boundary lines (?rågångar?) and boundary markers in the form of rocks, and an own survey of two hamlet boundaries in southeast Sweden. Many of the boundary rocks were subjected to unintentional damage or destruction that arose during forestry activities, the excavation of ditches, or road construction. Boundaries between hamlets sparsely populated areas were not clearly defined from the beginning, but were established initially in the form of boundary zones, that often consisted of wetlands, watercourses, or mountain heights.

Wind is used as an energy source all over the world. To be able to use this effectively, there is a need for as good forecasts and forecast models as possible. One of these models is Coupled Ocean/Atmosphere Mesoscale Prediction System (COAMPS®) that is used to calculate short time forecasts. This model is used here to calculate wind speeds at two different areas in Västra Götaland, Bengtsfors and Vänersborg. There are also wind measurements with SODAR stations for these areas.

City of Malmö has ambitions for the district Hyllie to become a demonstrative area ofsustainable urban development. As a part of this the following report aims to investigate the potential in using noise barriers combined with photovoltaics along Annetorpsvägen to generate solar electricity. To quantify the losses that shadows from buildings along the roadmight cause, a 3D-model of the area was constructed in SketchUp. This digital model made it possible to simulate shadows and how they change over the year. A reference model of a photovoltaic noise barrier (PVNB) was constructed and used to find the dates on which the solar cells are shadowed depending on building heights and positioning of the barrier.The results show that two lengths with a total distance of 400 meters is appropriate for applying photovoltaic noise barriers.

The purpose with this thesis is to get a compilation of all the critical bolted joints of all enginesproduced at LV Motors. ABB LV Motors produces induction engines with seven shaft heights. Eachengine size exists several variants of components ex. standard shield and flange shield. Depending onwhich components the engine is equipped with arises various types of strains in the engine's parts,certain assembly ways are more favourable than other.The most critical parts in the engine from a mechanical point of view are the screw units betweenshield/stator, feet/stator and bearing cover/shield.