With increased deployment ofintermittent renewable energy, such aswind and solar power, energy storagebecomes necessary to help reduceproduction peaks. Thermoelectric EnergyStorage is a method still in researchphase, which stores electricity in hotwater at a temperature of 120 ° C. Thisthesis aims to examine whether theThermoelectric Energy Storage would bepossible to integrate into existingpower generation such as a combined heatand power plant, and how the technologypotentially could function in theelectricity market. ThermoelectricEnergy Storage consists of a chargingprocess and a discharging process, bothoperating by the working fluid CO2. Toincrease the efficiency of theThermoelectric Energy Storage, wasteheat from the district heating networkis integrated.A model of the Thermoelectric EnergyStorage has been developed and it wascalculated by thermodynamic propertiesof the working fluid, CO2, in thevarious process steps.

Projektbeskrivning: Bakgrund: Vid valsning av tunna band med hög hållfasthet används reversibla mångvalsarsverk. Kundkraven är höga vad gäller bandens planhet. Planheten kan styras genom de planhetsställdon som valsverket är utrustat med. Syfte: Förvärva kunskap om hur de olika ställdonen inverkar på planheten. Varje enskilt ställdons inverkan på planheten kan undersökas genom att genomföra en föreskriven förändring av ställdonets läge och därefter utvärdera planhetsförändringen som uppkom.

Aeroseum is an aviation museum located in an old military underground hangar. The ventilation system in the hangar is designed for the military purpose of the hangar. This design includes a solution with air flowing through the space between the construction of the hangar and the rock surface. The solution is intended to avoid a buildup of inflammable gases. This design leads too high humidity levels in the hangar.

This thesis work has been carried out at the consultant company Pöyry Sweden AB in Norrköping, whom performs the task for E.ON heating Sweden AB, Händelöverket in Norrköping. The report shows methods to manufacture slurry consisting of fly ash and water. The slurry shall be pumped into several former oil storage rock shelters that E.ON has put into operation for the specific purpose. The ash mixture also develops hydrogen gas in contact with water.The work has aimed to produce different suggestions of methods and equipment that can be used for the objective. Mixing method and security issues were in centre while working with the suggestions.

The purpose of this master?s thesis is to contribute to the development of business relationships between a supplier and its customers. The research area and research problem was further developed into three research questions. The research questions concerns the following subjects: the substance of business relationships and dimensions within relationships management that can be used in order to contribute to the development of a company?s business relationships.

En studie i hur lekar kan inspirera till digitalt gameplay och samtidigt förmedla lekarnas kultur till spelaren. Detta har testats genom att göra ett prototypspel där varje bana är baserad på en leks mekaniker eller mening. Spelaren måste själv i slutändan analysera banan med en beskrivning av leken som sin enda ledtråd. Detta för att om spelaren själv blir engagerad och ska minnas vad den gjort kommer spelaren på så sätt minnas kulturen det medförde..

Industrialization of construction is by some considered to be a solution to the building industry's problems about the lack of quality, high production costs, low productivity and poor environmental adaptation. Meanwhile, industrialized construction partly earned a bad reputation after the million housing program. As large-scale projects where promoted during this period, it worked very well to use the technique of construction elements. In the mid seventies though, criticism arose which claimed that the aesthetic qualities had been deprived in the corporates effort to make housing production as efficient as possible.Tyréns, Derome and CBBT (centre for building and housing in wood) cooperates in a development project to develop a building system for 4-8-storey buildings, consisting of three platforms: a technology platform, an IT platform and a processing platform. The technology platform consists of flexible, industrially built flat modules of wood and from this platform the subsystem stairwells, is broken out.

At present day there are several different methods for measuring of paved surfaces.The most common methods today are measuring with a total station, the GlobalNavigation Satellite System (GNSS) and terrestrial laser scanning (TLS). Recently thedevelopment of unmanned aerial vehicles, known as drones, has increasedexponentially and today there are several ways of using drones for measuring surfacesby photographing and laser scanning.This thesis contains a comparison between the methods terrestrial laser scanning(TLS), and unmanned aerial vehicle photogrammetry (UAV). The measurements havebeen applied on two different test surfaces, one of asphalt and one of gravel. Thepurpose of the comparison is to investigate whether the airborne photogrammetry isequivalent accurate in its height levels as the terrestrial laser scanning. For thecomparison to be more extensive, these two methods have not only been comparedin precision but also in the areas of ease of use and economy.The precision was analyzed by comparing the height levels in randomly placed controlpoints on the test surfaces.

Traditionally, rolling mills use emulsions based on a mixture of oil and water for lubrication. Since two years ago SAPA has been using (instead of oil) a synthetic lubricant so called conditional emulsion for hot-rolling of aluminum. This lubricant is water based and homogenous at ambient temperature, but switches to a two-phase system at heating above the cloud point.This project aims to validate and if necessary modify an existing HPLC method for quantifying two out of three key components (A, B and C) in the conditional emulsion. Attempts to develop a method to quantify the pH adjusting components, X and Y were also made. These two methods are required to optimize the lubricant.Due to the complexity of the components, it has been difficult to present a method for quantification, and HPLC with ELS detection was chosen after a long series of trials.

The Transport division is responsible for the internal transports on Sandvik MaterialTechnology AB. At the moment there is no clear picture of how the straddle carriers aremoving at the division Primary Products and if it is working in a satisfying way. It isimportant to see the whole picture of the transportation flow so improvements can be made.The purpose of this essay is to survey and analyse the truck flow in a Lean Productionperspective. The essay is delimited to only include straddle carriers transportation ways in thePrimary Products division. To survey the truck flow we have used a method called Walkthrough.This means that we have walked thorough the whole production flow andinterviewed some of the employed on the way to get the necessary information.

Detta är slutreflektionen över ett kandidatarbete gjort av Karl Tannergård och Per Thulin. Arbetet har gått ut på att skapa en prototyp av en barnspel baserat på Inger och Lasse Sandbergs böcker om Lilla Spöket Laban och hans familj. Spelet är tvådimensionellt och vänder sig till barn i åldern fyra till sju år. Det är skrivet i programmeringsspråket Python och använder multimediabiblioteket pygame. Utvecklingen har skett i samarbete med animationsstudion PennFilm AB..

Detta examensarbete är utfört på Sandvik Materials Technology (SMT) i Sandviken. SMT har under ett antal år arbetat mot att infria deras två största kunders, Atlas Copco Secoroc och Sandvik Mining and Construction, önskemål om en leveransprecision på 95% och en ledtid på tre dagar för storvolymprodukter av bergborrstål. Idag är leveransprecisionen tillfredsställande medan ledtiden är fem dagar. Examensarbetets syfte är att analysera vad som krävs för att infria Atlas Copco Secoroc's och Sandvik Mining and Constructions önskemål om tre dagars ledtid för storvolymprodukter. Ledtidsreduceringen ska åstadkommas med nuvarande skiftform och utan att leveransprecisionen påverkas i negativ riktning.

Med ett energikombinat vid Lillesjöverket vill Uddevalla Energi energieffektivisera samt sänka temperatur på återkommande fjärrvärmevatten, för att kunna utnyttja rökgaskondensorn effektivare. Uppdraget var att utreda mängden tillgänglig energi under sommarhalvåret och utföra en matematisk kalkyl som ska ligga till grund för val av tork. Valet stod mellan två alternativ av tork där storlek på värmeväxlararea och investeringskostnad skilde dem åt. Sedan följde dimensionering av fjärrvärmeledning samt cirkulationspump från fjärrvärmenätet till tork. Syftet var att ge Uddevalla Energi ett tekniskt beslutsunderlag för val av storlek på tork samt dimensionering av energiöverföring till densamma.

Title: What drives the customer's choice of packaging and which factors influence the customer's packaging cost? ? in the automotive and manufacturing industriesAuthor: Lena AnderssonSupervisors: Annika Olsson, Division of Packaging Logistics, Lund Institute of TechnologyHelena Claesson, Volvo Logistics ABProblem: Which parameters are important for logistic people to think of when they are going to choose a package?Which cost factors are included in the packaging cost?What kind of added value can an emballage supplier provide their services with?Purpose: The purpose of the project was to study the parameters that drives the customer's choice of packaging and the factors that influence the total packaging cost. The study also consists of a valuation of what an emballage supplier can offer to add value to their services.Method: The study is based on interviews with people who are working at Volvo Logistics and Volvo Car Corporation. Volvo Logistics provide their customers with standard packaging material, which they own and administrate. Volvo Car Corporation is one of their customers.

The present study examines a new production line of glue-laminated wood (glulam). The glulam is produced from non-planed boards of spruce, which also is convex, that is pressed together with high pressure during the gluing. According to a economic calculation, the material has a economical potential mainly on account of the absent planning. The study mainly found out that the shear strength of the material tolerated the demanded values in standard SS-EN 386, but the delaminating values did not. Since there are more areas to be studied around the material, the prospect to achieve the right delamination values is seen as positive..