Heat is distributed to the district heating customers through pipes with water as a heat carrier. The district heating system is complex. To decide what is leakages from the district heating net versus what is the water consumption of the plant, is difficult. Therefore, the purpose of this master thesis is to establish a model where the district heating net?s leakages but also the water consumption of the plant can be followed daily. The project is performed at Vattenfall´s district heating power plant in Uppsala. Information is gathered through discussions, drawings of the plant and guided tours of the plant.

This report investigates a possible solution to the problem with adapting wave powerplants to work in countries with tidal water. The wire connecting the buoy at the surface with the generator at the bottom needs to adjust to the varying water depth. Our solution to this problem is to attach the wire to a jack which is then placed inside the buoy. The jack is then powered by an electric engine. The report discuss what forces the buoy will be exposed to and then the structural integrity of the design is evaluated through simulations.

People in today?s society are becoming more and more aware of how important it is to use energy as efficiently as possible. This is clearly noticeable by an increase in home produced heat with e.g. solar panels or heat pumps heating systems. These changing customer demands forces district heating technology to be redesigned, which is why there is an ongoing research regarding the next generation of district heating - low temperature district heating (LTDH).

This report covers a product development project conducted as Bachelor of Science thesis forthe Innovation & design engineer program at Karlstad University.The assignment was supplied by MMB Consulting, Kristinehamn. The purpose of this projectwas to find an alternative way of shaping wire-net insulation mats. This insulation product isused for fire and thermal insulation of technical installations. The insulation consists of stoneor glass wool with a sewn on steel wire netting on the out facing side. This netting has thepurpose to enable fastening to e.g.

A large amount of our time is spent indoors in an artificial climate. To make the experience pleasant there are requirements on the ventilation and the heating system. At the present time the most common form of heating is a radiator system complemented with a ventilation system. A ceiling heating system with combined heating and ventilation can replace the two separated systems. The benefit with a ceiling heating solution is that it saves space since the radiator system is no longer needed.

The ?civilized? world is in need of fossil fuel in order to function. Hybricon AB is a company in Umeå that is developing a technology that hopefully can reduce parts of this need. They are currently testing their two electrical busses (with Hybrid backup) in city traffic on the roads of Umeå in cooperation with the county of Umeå.                               The busses are originally diesel-busses, but the diesel motor has been replaced with two electrical hub-motors with a power of 145 kW each that are powered by batteries.The batteries are charged at the end station after each route. In case the batteries should run low on capacity during driving, they can be recharged by the so called genset.

In this report a study has been done regarding different heating systems on which are the mostcomprehensive with solar heating systems. The report has also been focusing if solar power can beused as a primary heating source for supplying more than 50 % of the buildings total heatingproduction. The University of Dalarna constructed a demo-house for this purpose and according tocalculations the total solar usage is more than 50 %. This house has been made for referenceregarding the design of the heating system of property 5:37.Further studies have been made to compare different heating systems that are compatible with asolar system, where the compared systems purpose is to be independent of direct using electricity. Asystem of this design is regarded as sustainable according to environmental as economic issues.

Many of todays studies show that district heating is one of the betteralternatives as heating source because of its low environmental load.The energy source is often leftovers from other processes producing energy or waste, like garbage or chips.Electricity in combination with geothermal heating is another heating system that has increased sharply during the last years, and also this system decreases the discharges that have negative affectson the environment compared to several other heating methods.This report aims to, concentrated towards these two different heating systems, estimate the amounts of discharges they indirect cause and how the environment is affected.We have calculated the mean value for discharges of carbon dioxide, nitrogen oxide, sulphur oxide and dust generated from electrical power used in Sweden.Through interviews and research we have gained data for the same substances that district heating based on combustion of garbage and biofuel generates.We have also in cooperation with a housing company chosen a building we see representative for many of the new single-family houses built in Sweden today.Based on its shape and appearance we theoretically created three alternatives of the same house, each of them with climate screens different from each other.Together with the amounts of discharged environmental affecting substances, these houses were the base for our calculations and studies when investigating the different heating sources environmental effect.The results have thereafter been analyzed and discussed from different angles..

Sandvik Wire needed a review of the administrative part of the order fulfillment process and especially the work around packing and the inventory of finished goods. Therefore we acquired the assignment to investigate the administrative part of the order fulfillment process in the company with the purpose to identify potential for improvement. This investigation was performed with focus on the terminal and packing functions. The purpose with the investigation was also to identify critical factors for an efficient order fulfillment process and investigate if information quality is such a factor.Data was collected through interviews and observations on Sandvik Wire. With the help of this data the information and material flows was mapped, the work within terminal and packing, and adjacent functions was investigated.

In this Thesis the possibilities of designing a larger building that is very energy efficient in the sense that it would not need a conventional heating system are discussed. Solar radiation transmitted through the windows, internal heat from occupants, lamps and electric appliances inside the building and heat recovered from the ventilation system then have to be sufficient for the heating of the building. This study is of general interest since the property company, Akademiska Hus, plans to use this study as a first step in determining if this technique could be used in the future and thus be worth further investments. A building without a conventional heating system of the size investigated in this project has not yet been built.The energy needed for the heating of the building was simulated using VIP+.The conclusions from the study are that it is possible to build large buildings without any conventional heating system. This could be achieved in many different ways, for example by lowering the inside temperature or by using better windows and heat recovery system with higher efficiency.

The energy use in a workshop company has been examined in this work in order to find areas for energy efficiency improvement. The combined oil and electricity heating in the company were compared with other alternative heating systems including cooling of the premises in following combinations:Ground source heat pump for heating and coolingDistrict heating and absorption coolingDistrict heating and low temperate surface water coolingEnergy use, operation costs and carbon dioxide emissions were calculated for the current heating systems and the three alternatives including cooling. The ground source heat pump for heating and cooling decreases bought energy with 34 MWh annually compared to current heating only. The district heating and low temperate surface water cooling has the largest reduction of operation cost and carbon dioxide. The operation cost decreases with 42 kSEK and the carbon dioxide with 43 metric ton CO2 annually.

This bachelor thesis aims at investigate how a specified house can optimize its energy consumption.Today the house often stands for the major part of the energy consumption in a consumers? life,whereas an energy optimization creates economic as well as environmental advantages. It is importantto make old houses more energy efficient, but putting high energy demands on new houses could beargued to be more important. The installations functions as both the heart and brain in a house, thusmaking it important to energy optimize these. Since the background describes the importance ofenergy efficiency and optimization in a house, the focus area of this report will be an investigation ofdifferent types of heating systems in order to be able to choose the one most suited for the house.Aspects considered when choosing the heating system was how economic the system is both inservice- and investment costs and how environmental and operational friendly the system is.Through literature reviews there were sufficient information gathered that served as a foundation whencomparing and choosing between the four systems - district heating, pellet-fired boiler, geothermalheating and solar heating.

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.

Life Cycle Cost, often abbreviated as LCC, is a common tool for comparing the total cost of different alternatives, such as heating and cooling methods. Common heating and cooling methods in Sweden are geothermal energy, district heating and district cooling. This report aims to evaluate how different heating and cooling methods differ from each other while being applied on three different types of buildings, using selected LCC-models. Information about the selected LCC-models wasretrieved from each separate model and its website. Reports and agencies were used as sources for information about the heating and cooling methods.