The aim of this thesis is to describe how to work with the development of language by reading aloud. I have chosen to look at the reading aloud project "Boksnurran" Book Wheel to see if it has influenced the daily work with reading in preschool. My questions are: How do they work with reading in preschool? Is the reading environment suitable? How do the staff describe their booktalks? What problems do they encounter? What can be improved? The thesis is based on qualitative interviews. Those interviewed have participated in "Book Wheel".

The Master Thesis work this report is based upon has been conducted in cooperation with Svea Teknik AB. Svea Teknik is a consultant firm which is developing parts of a tunnel boring machine on behalf of Atlas Copco. The machine is being developed to mechanically excavate hard rock by fixating itself in the tunnel and then press a large rotating cutter-wheel equipped with disc-cutters against the tunnel wall. The disc-cutters are the tools that are in direct contact with the hard rock and are therefore exposed to extensive wear and needs to be replaced on a regular basis.The purpose of this Master Thesis has been to develop a service equipment that will enable time effective and safe changes of disc-cutters. The disc-cutters have a diameter of 17 inches and weigh about 130 kg.

 Denna uppsats behandlar hur sourcingprocessen av komplexa system på Försvarets Materielverks (FMV) kan struktureras genom att undersöka parametrar som är viktiga att beakta vid outsourcing. En del av FMV:s strategi grundar sig i att minska den interna verksamheten och att lägga större åtaganden på leverantörer av systemlösningar, för att på så sätt kunna minska behovet av interna resurser. Därför blir det viktigt att besvara huruvida systemansvar bör tas av FMV eller av en leverantör.Rapporten behandlar processen om att fatta ett beslut om make-or-buy och när och varför det är motiverat att överlåta systemansvar till leverantörer. McIvors modell om outsourcing används för att besvara frågan hur FMV bör fatta ett beslut rörande make-or-buy genom att modellen tillämpas på tre pågående projekt. Därefter används "the strategic supply wheel" för att bedöma vilka parametrar som är viktiga att uppfylla både internt och externt vid outsourcing av aktiviteter beroende på om tid, kostnad eller kvalitet är prioriterat i respektive projekt.

?Optimizing the workflow of hydraulic reservoir tanks? is a degree project made by Jonas Olsson, student within the faculty of technology and science, during spring semester 2012. The project comprise 22,5 ECTS.Volvo Construction Equipment, located in Arvika, was the client in this project. The mentor at Volvo CE was A?sa Barck, and the mentor at Karlstad University was Monica Jakobsson.

Köpingsföretaget GETRAG All Wheel Drive AB utvecklar, tillverkar och levererar komponenter för drivteknik till personbilsindustrin. Genom projektet 580-9 planerar företaget att införa en monteringsbana för en nyutvecklad produkt. Till denna önskar företaget skapa en materialhantering som är kostnadseffektiv, lever upp till kundernas krav på hög kvalitet samt utesluter hantering av träemballage vid monteringsbanan. Syftet med examensarbetet är därför att ge förslag till en kostnadseffektiv materialhantering där emballage som avger restprodukter inte hanteras vid monteringsbanan.För att undersöka examensarbetets frågeställningar har vi utrett hur materialförsörjningen till banan bör skötas. Studien bygger främst på teorier om lean produktion och förpackningslogistik.

This report is the result of a master thesis at the Department of Mechanical Engineering, Division of Industrial and Economical Development, at Linköping University of Technology. The project was carried out on behalf of Fanerami AB, Mjölby and includes 20 weeks of full time schedule work.Cabinets with vertical mounted roller shutters all share the same problem, namely weight balancing. A roller shutter has an equilibrium area where the sum of the different forces acting on the shutter equals zero. As the shutter leaves that area it will pick up speed as it falls towards the bottom. When the shutter hits the bottom of the cabinet there is a potential risk of getting fingers caught and in this project a solution to prevent this from happening was to be presented.In this project, three concepts have been generated with the following different purposes:?In concept 1 the risk of getting any fingers caught when the shutter closes was to be eliminated in an efficient and inexpensive way.?In concept 2 the roller shutter had to be balanced at all time providing the possibility to keep the cabinet open in any position.?The last and most challenging task was to create a remote controlled TV cabinet.

Volvo in Arvika produces Wheel loaders, and the production is based on forecasts. When a machine is ordered, the customer can choose what type of equipment he or she wants, and these equipments are also made forecasts on. This is made by giving each equipment an estimated procentual usage that shows how many of the machines that will use this option. Today two people are working with the forecasts, planer A in Eskilstuna and planer B in Arvika. Planer A makes a forecast based on the historical outcome and planer B then makes adjustments of this based on how many options that are ordered.

To design new and high tech products the engineers rely more and more on computer based simulations to investigate the properties and behavior for a component or system.To verify these computer based simulations the dynamic properties for the components of the drivetrain needs to be verified. Therefore measurements of the stiffness and vibrations for the rear axle has been performed. This report show how the measurements has been implemented and evaluated, along with some interesting results for the rear axles properties.The static stiffness for the drive shaft along with the axle-gear has been determined. It is found that the stiffness for the whole rear axle is near the stiffness for the drive shaft, which means that the drive shaft becomes the dominant component of the system and affects the rear axle stiffness the most. The measured stiffness of the driveshaft is close to its theoretical stiffness.The stiffness for solely the hypoid-gear have been calculated using the stiffness for the rear axle and driveshaft, and thus has a range for the stiffness of the hypoid gear been determined.The backlash for the whole rear axle and for some individual components has been determined, where the backlash between pinion and crown-wheel has negligible impact on the total backlash.Measurements of the crown-wheel and pinion movements have been conducted, where the direction of movement is consistent with the theoretical direction of the forces.The vibration measurements show that the vibrations are more severe at certain rotational speeds.

Denna uppsats kommer att handla hur man kostnadseffektiviserar produktioner och arbetar som ett produktionsbolag mot Webb-tv. Skillpoint, som skriver recensioner, publicerar nyheter och gör intervjuer inom spel, har varit vår uppdragsgivare. Genom samarbetet med Skillpoint har vi under kandidatarbetet producerat videor i form av intervjuer, reportage, serier, topplistor och spelrecensioner. Produktionerna har bestått av antingen Skillpoints eller våra egna idéer..

This report deals with an exam report written by Olle Hjalmarsson and Thomas Likar, students at Högskolan i Halmstad. The project was carried out for Haldex Traction AB in Landskrona whose business consist of manufacturing automatic all wheel drive systems (AWD-system). These systems consist of a plate clutch which activates all four wheels of a 4-wheel driven vehicle. An important component in these clutches is the accumulator which basically consists of a piston under the load of a spring which creates an oil pressure with the help of an electric motor used for actuating the clutch.At Haldex difficulties has been experienced regarding the assembly of the accumulator parts due to the small tolerances between the piston and the hole of the accumulator in the cast aluminium housing. Attempts have been made to assemble the parts in existing robot cells.

Eco-design is all about improving products environmental performances throughout the products lifecycle by including the environmental aspect into the product development process. There are a large number of different tools that can be used for this, but there are several factors that can affect which one will be the best to use. Some tools for eco-design takes comprehensive studies and can only be performed by experts, while some tools can be used more time- and cost efficient and with basic knowledge. The choice of tool should be based on the company?s situation.This report describes the research of how the design and furniture company Blå Station could include a tool for eco-design in their product development process.

Denna uppsats kommer att handla hur man kostnadseffektiviserar produktioner och arbetar som ett produktionsbolag mot Webb-tv. Skillpoint, som skriver recensioner, publicerar nyheter och gör intervjuer inom spel, har varit vår uppdragsgivare. Genom samarbetet med Skillpoint har vi under kandidatarbetet producerat videor i form av intervjuer, reportage, serier, topplistor och spelrecensioner. Produktionerna har bestått av antingen Skillpoints eller våra egna idéer..

Saab Aerosystems has a long tradition and a lot of competence in the field of flight simulation. Their ambition to broaden the market horizon has led to a discussion about also selling vehicle simulation solutions, both for military and civilian use.The aim of this thesis is to investigate the driver?s experiences of the accelerations he or she is exposed to whilst driving in rough terrain. The results may be used as a basis for future decisions and can act as a platform for the construction of an effective simulation model.To investigate the driver?s exposure of acceleration, some kind of dynamic simulation is needed.

Den här rapporten avhandlar arbetet med att ta fram ett förslag som förlänger Volvos kärnvärden - kvalitet, säkerhet och miljöhänsyn, ut i Utvecklingsverkstaden på Volvo Construction Equipment, Hauler Loader Business Line, i Eskilstuna. Förslaget är utformat som ett koncept, som ska kunna överföras till andra verkstadsmiljöer på Volvo, om så önskas. Idéförslaget har baserats på en studie av den befintliga Utvecklingsversktaden. En modell av verkstaden i skala 1:50 utformades som presentationsmedium.Vid examensarbetets slut har förslaget presenterats och utvärderats av målgruppen. Den primära målgruppen har varit de anställda på avdelningen.Slutsatserna av arbetet är att en informationsbärande interiör kan formges för att representera ett företags kärnvärden och visa på innovation och framtidstänk.

En ökad kostnadseffektivitet i svenska företag är viktigt för att dessa ska kunna bibehålla sin internationella konkurrenskraft. Då el- och andra energipriser förutsägs stiga i framtiden ökar även företagens energikostnader. Genom energieffektivisering kan företag minska sina kostnader utan att förlora konkurrenskraft.Detta arbete har utförts på GETRAG All Wheel Drive AB i Köping och syftar till att kartlägga företagets energianvändning och därigenom lokalisera potentiella möjligheter till energieffektivisering av företagets olika processer. Kartläggningen har haft särskilt fokus på elenergianvändningen då denna står för den största kostnaden bland energislagen. Hänsyn har endast tagits till möjliga besparingar och ingen investeringskostnad för effektiviseringsåtgärderna har beräknats.Kartläggningen har genomförts genom mätningar av elanvändningen på produktionsnivå i kronhjulstillverkningen samt insamling av övergripande mätdata över elanvändningen för övriga stöd- och produktionsprocesser.