AbstractResource efficient manufacturing is a term that has been increasingly applied within manufacturing, where one of the key points is to reduce waste of such forms that do not add value for the end customer. By the Lean principles, there are seven plus one types of waste, in which the definition of the eighth point varies among sources. In this study, the eighth type of waste has been interpreted as the untapped creativity and competence among employees that has not been put to use. From this, our question was incubated; How can you make the most of the employees? untapped creativity and potential within manufacturing? The case study will be developed with empirical data obtained from Dometic Group by conducting interviews.From the gathered literature, it was concluded that the communication between employees contributed to an increased understanding of one another as well as it allowed for improvement in work.

ABSTRACTThis project thesis has been written at the request of Mälardalens University, Västerås.The aeronautical engineering students at Mälardalens University and the pupils of Hässlö upper secondary school, all gets the opportunity to perform a computation lab with a real turbojet engine during their study. The goal of the lab from the University is that it should give the students applied experience from the theory part of which has been tought in the course ?Aircraft Engine Technology?.                      The pupils of the Hässlö upper secondary school are performing simpler calculations from the measured values of the equipment. This turbojet engine is located at Hässlö airport in the premises of Hässlö upper seconday school.Since the installation 1989, the engine has lost both thrust and reliability. This makes the theoretical computations made by the students inaccurate.

In the pilot plant at Hammarby Sjöstad, Sjöstadsverket, several new methods are tested in order to achieve a good use of resources. When a new technique is considered it is often the performance of the technique itself, under given conditions, that is evaluated. However, in order to evaluate the overall function the whole picture is needed. With a system analysis it becomes possible to make a comparison where all the positive aspects are put up against the negative ones, for the technique itself as well as its requirements. In this way the influence that minor components have on an entire system can be considered.This report presents a system analysis of an anaerobic membrane reactor (MBR) with a VSEP-membrane (Vibratory Shear Enhanced Process).

The purpose of this degree project was to build laboratory equipment for a new course in power electronics that starts this autumn 2010 at Uppsala University. The equipment is intended for student labs and it covers the most important areas of the course including rectifying, buck-/boost-converters and PWM-modulation. It is built as one sealed unit where all the electronics are built-in but visible and it has a connection board where students safely can connect the different circuits. The project has advanced from theoretical studies of circuit design, choosing of components and simulations to drawing the printed circuit board (PCB), soldering, case building, final testing and troubleshooting - basically most steps from an early idea to a final product. Measurements on the final product gave about the same results as the earlier simulations of the circuits and the result is overall satisfying..

As a small and land scarce country, effective waste management is ofoutmost importance in Singapore. In this study the production of biogasthrough anaerobic digestion from the organic fraction of municipal solidwaste (OFMSW) was compared to incineration of the waste. At the momentalmost all of the OFMSW in Singapore is incinerated. Three differentscenarios were compared to the reference scenario (incineration): one with alarge scale biogas plant that can treat half of all OFMSW in Singapore, onewith a medium scale biogas plant about 15 times smaller than the large oneand one with a small scale biogas plant that can treat waste from e.g. ashopping center or a food center.By using life cycle assessment (LCA) the different scenarios were comparedin terms of global warming potential (GWP), acidification, eutrophication,energy use and land use.

The municipality of Västervik, with support from Envipro Miljöteknik AB, is carrying out a main study of the minefields at Gladhammar. Mining of iron, copper and cobalt under different periods from the 16th century until the end of the 19th century has led to discharges of metals to the lakes situated downstream. The aim of the main study is to investigate the possibilities to reduce the environmental load on the surrounding ground and water caused by heavy metals from the mine. The present report is a part of the main study. The aim of the work is to investigate the geochemistry of the groundwater.

Today many different types of lock systems are used all over the world. Passwords, finger prints and magnetic strips are a few examples. When the key is a three dimensional object, lika a physical metal key, the security depends, in a high degree, on that you can?t copy the object without access to it. One approach to copying the object is photographing the object, and from these photographs create a copy.

The biogas plant Kungsängens gård, owned by Uppsala Vatten och Avfall AB, produces biogas and biomanure from organic household waste, food processing waste and slaughterhouse waste. In year 2012, 4.4 million Nm3 of biogas were produced from 25 200 tons of waste. Before digestion all substrate is sanitized by pasteurization at 70°C in order to kill pathogens. Another method, integrated thermophilic sanitation (ITS), is of interest in order to decrease the energy demand. The method implies that the substrate is sanitized during ten hours in the digestion chamber, where the temperature is 52°C.

At Volvo Cars Torslanda's paint shop there is a requirement to in a fast and effective way get an overview of the plants capacity. Therefore a capacity template was constructed as a tool for the engineers at Volvo several years ago. This template has during the years become complicated and outdated. Thus this thesis work will resort as a new capacity template, built from scratch. The new template has been built up based on requirements from Volvo and the concept of OEE (Overall Equipment Effectiveness).

The Intensive Care Unit (ICU) is a special unit for patients who is in the need for emergency life-sustaining measures and every patient has complex medical- technical equipment. The experiences of a critical illness and the needs of critical care are experienced in different ways. The purpose of this study was to describe the experiences from patients in the ICU and how this experience has an influence on the patients. The method was a study of literature with a qualitative inception based on eight scientific articles and the analysis of content has been inspired by Graneheim and Lundman (2003). The result of the study is presented by four categories: to loose the ability to make themselves understood, to be forced to adjust to the environment of caring, to have the lack of connection with reality and to be in an intensive care environment, The results showed that patients in the ICU are affected by the attitude from the staff, the equipment around them as well as the sounds and lights in the environment there.

In recent years the construction industry has been exposed to increased time pressure which has resulted in a higher amount of wastage. Today 35 % of all construction projects in Sweden is "wasted". Time pressure has risen due to increased competition on the market, with more actors entering the construction business, therefore profit margins decreased which has led to a more pressing need for decreasing the amount of wastage.Bravida is Scandinavia's largest supplier of installations and provides specialist services in electrical installations (heating and sanitation), and ventilation. Mahdi Bawaqneh's task was to investigate where, how and why wastage occurs in the company's projects and how to prevent such wastage. The thesis covers the subjects of lean production, communication in projects and planning of projects.

In 1994 the EU directive of packaging waste was adopted. The result was that all EU member states developed different systems to manage packaging waste and recycling. This paper examines the various systems and the factors that affect the level of recycling. This is done by a cross-sectional study between countries. The results of my study suggest that take-back system generates less recycling than other systems, the mandatory deposit system can affect the recycling in a positive way.

Vid Volvo construction equipment AB, Component division i Eskilstuna, har nedväxling i förpackningsstorlekar genomförts som en del i en omfattande omställning mot Volvo Production System och Lean. Genom att producera med mindre satsstorlekar och hemtagningskvantiteter, vill Component division sänka sin kapitalbindning och bli flexiblare mot variationer i produktionen. Dessvärre påverkar nedväxlingen förpackningskostnaden till följd av ytterligare hantering, transport och administration. För Component division är det viktigt att få en god uppfattning om hur alla förpackningskostnader utvecklas med tiden. De vill i framtiden följa ett lämpligt nyckeltal för att se hur effektiva de är inom förpackningslogistik samt hur beslut och förändringar påverkar kostnaden.

The aim of thesis was to, through a action research study and through individual interviews with five students, clarify their perspective on educational assistance in high school. The study shows that students prefer teaching in small groups outside of regular whole class because it gives the them access to the factors they consider crucial for a functioning support-time whit a skilled and dedicated teatcher, in a calm and safe environment. Moreover, the students claim the importance of technical equipment especially in the Swedish subject, but also in other subjects. Today the educational assistance varies from an outside-the-class teaching situation to a whole-class situation with teacher support as well as technicaal equipment. When the student were asked to describe the cinditions under which studies can be conducted with the whole class they tried to imitate the learning environment they have in a small group.

Holmen Skog is currently using a GPS-program called TraktInfo, originally developed within the company. They are now planning to switch to a new GPSprogram or allowing the contractors to buy other programs available from the logging equipment manufacturers. To be able to offer this flexibility, Holmen Skog needs to obtain information about the features offered by the different manufacturers in their specific programs, and also when the manufacturers are planning to start selling programs adapted to the new standard called StanFord2010. According to the study, the manufacturers are hesitant to StanFord2010 and there has also been a lack of clear signals from the customers and clients about what kind of different new features to include in the programs. The feature most frequently used by forest machine operators today is the option to keep record of the harvester?s path by creating a ?log plot?. This feature was not used to its full potential however, since only one out of eight of the forwarders included in the study had computers that were compatible with the harvester?s computer.