The division of Engineering Materials at Linköping University, department of Management and Engineering, conducted a research project concerning Fatigue life of thermal barrier coatings during 2009. During this project equipment to provoke these fatigue failure by rapidly heating and cooling test subjects in cycles, was ordered.Design and manufacturing of the equipment was handled internally at LIU.The equipment was built using a furnace that is lowered and raised over the table where the test subject is placed. To keep the temperature of the furnace a lid slides in place to close the downward facing opening of the furnace when it is in the raised position. On this door there is nozzle that is used to cooling of the test subject by air.To make sure that the equipment can work independently you need an automation controller that can evaluate if movement can occur without danger of collisions. The control system also needs to monitor that all elements are performed according to plan.This degree project is based on a modular system from OPTO 22 and includes the configuration of a PLC that will be supplied with logic and a user interface.The degree project resulted in a graphic interface in which a user can set desired values for different parameters and get information about current values for them.

The construction industry has not undergone the same logistical development as the manufacturing industry; this, in combination with increased material price, leads to the fact that the construction industry must be improved. This master thesis is a part of the research cooperation Brains & Bricks goal of reducing production costs for the construction sector by 25 percent. Brains & Bricks is a cooperation between Linköping University, Peab and Katrineholms municipality. The master thesis aims to identify improvements in the flow of material, the Supply chain operation reference, SCOR, model has been used and the work has been carried out on one of Peab?s construction sites. At present the business is characterized by bad communication both between the construction site and the office as well as between the construction site and suppliers.

This master thesis is an early concept development project about using plastic films and sheets as materials for shaping openings for Tetra Pak packages. It is also a technical introduction highlighting the areas of importance for the development of plastic film and sheets openings. The master thesis has been carried out as a co-operation between Chalmers University of Technology, KTH Royal Institute of Technology and Tetra Pak AB.The master thesis study presents an introduction that gives an understanding of the technical complexities and design possibilities of using thin plastic films and sheets in liquid carton openings. The knowledge is then transferred into five design concepts which points out the areas of opportunity. The technical introduction is widespread and extensive covering current packing trends, the liquid carton package and openings, thermoplastic material properties, and thin film and sheet manufacturing and shaping.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.

This Master of Science thesis was a part of Pharmadule Emtungas project to construct a mobile automated cell for welding of carbon steel pipe (Heating, Ventilation and Sanitation). Pharmadule Emtunga is using a modular building concept for building pharmaceutical factories. The modules contain these pipes. The goal of the thesis was to present concepts for technical solutions regarding welding methods and fixtures for the cell. Conceptual models for the cell were made with aid of CAD software.

This bachelor essay is divided into two parts, the first being a construction of a single-familyhouse and the second an in-depth study of five different isolation materials, analysed from anenergy perspective.The first part, the construction of the single-family house, has been created from knowledgeacquired during three years of studying at KTH Royal institute of Technology in Stockholm, inthe program Architecture and the Built Environment. The constructed house is a one-floorhouse of 137m2with façade plaster, situated in Borlänge, Sweden. The house has a wooden framewhich is built on a on sight cast concrete foundation, on the ground. The house?s roof is a gableroof, which has an angle of 24 degrees.

Abstract: Title: Communication of and around internal performance reports - A study in seven manufacturing companies based in Blekinge. Authors: Marcus Harrysson and Mikael Johansson. Supervisors: Lars Svensson and Carina Svensson, Blekinge Institute of Technology Department: Department of Business Administration. Course: Bachelor thesis in Business Administration, 10 credits Purpose: Our purpose with the bachelor thesis was to investigate if there is a connection between communication of and around internal performance reports and profitability in companies. Method: Our investigation has been made at seven companies in the county of Blekinge by making personal interviews with people in both production and business departments at each of the companies. Result: We have come to the conclusion that there is a connection between communication of and around internal performance reports and profitability. Sammanfattning Titel: Kommunikation av och runt interna ekonomiska rapporter ? En studie i sju tillverkande Blekingeföretag. Författare: Marcus Harrysson och Mikael Johansson. Handledare: Lars Svensson och Carina Svensson, Blekinge Tekniska Högskola. Institution: Institutionen för Ekonomi och Management Kurs: Kandidatarbete i företagsekonomi, 10 poäng Syfte: Syftet med kandidatuppsatsen är att undersöka om det finns ett samband mellan kommunikation av och runt interna ekonomiska rapporter och lönsamhet. Metod: Vår undersökning har gjorts i sju stycken Blekingeföretag genom personliga intervjuer med representanter för både ekonomi- och produktionsavdelningen på varje företag. Slutsats: Av vår undersökning drar vi slutsatsen att det finns ett samband mellan kommunikation av och runt interna ekonomiska rapporter och lönsamhet i företag..

Title AB Volvo Pentas packaging system ?process and packaging logisticsAuthor Peter Powell, Lund's Technical CollegeSupervisors Annika Olsson, Lund's Technical CollegeJan Svensson, AB Volvo PentaProblem - Packaging requirements ? Which requirements are there, how do they affect each other and how are they fulfilled?- Packaging process ? what is the line of action when developing new packaging and making adjustments in existing ones? Who has the responsibility to do what?- Packaging logistics ? How is the packaging system adapted to transport efficiency and handling?Objective To create an overall picture over how the packaging system affects and is affected by different functions and players within and beyond the company boundaries, to give a clear picture of how changes in the packaging system is made today and how it could work and finally to give suggestions for cost savings affected by the packaging system.Method The methods used for this thesis has mainly consisted of action research and at some extent case studies. As a previous employee at the department of logistics at Volvo Penta I?ve taken part of the environment, information and prerequisites that this thesis discusses on a daily basis. Case studies have been used for the collection and analysis of data concerning packaging logistics as I?ve chosen to consider only specific markets and packaging.Conclusions This thesis has highlighted the demands that are placed upon engine packaging throughout all concerned units and how these demands affect each other, positively and negatively.

Syftet: Syftet med denna uppsats var att se hur Nordiska Afrikainstitutet använder sig av sociala medier och hur de tillämpar den information som organisationen kommunicerat via de sociala medierna.Teoretisk ram: Uppsatsen utgår ifrån teorier som ger överblick i hur traditionella och moderna kommunikationsredskap fungerar. Därutöver har ett analytiskt instrument använts som kartlägger kommunikationsprocesser i organisationer samt hur dessa tar tillvara på ny kunskap. Den teoretiska referensram består av följande teorier: Media Richness modellen samt de två artiklarna On using organizational knowledge capabilities to assist organizational learning samt Virtual worlds as platforms for communities of pratices från antologin Knowledge management and organizational learning.Metod: Uppsatsen bygger på en kvalitativ metod. Det empiriska materialet har samlats in genom respondentintervjuer, dessa bestod av telefonintervjuer samt epostkorrespondens. För att urskilja respondenterna har ett snöbollsurval använts. Intervjuerna har därefter analyserats utifrån den teoretiska referensramen.Resultat: Resultatet av undersökningen visar att både traditionella och sociala medier används vid institutet där de traditionella medierna anses trovärdiga men inte alltid flexibla. De sociala medier som används är Facebook, Twitter och institutets egna forum kallat NAI-forum.

Laser for material processing possesses a number of advantages which mean that it has been and will be an important component for a wide range of industries' future development. Cutting materials processing is the dominant use of laser technology and has revolutionized the manufacturing industry. The aim of this thesis is to describe the principles of metal cutting by laser, how laser cutting is applied in practice and to identify how Swedish companies are using laser cutting. For the theoretical and technical description of laser cutting literature studies are the primary source of information. The empirical basis for the mapping of the Swedish industry for laser cutting is grounded on a survey; this includes Swedish companies that use laser cutting in their production.

This master?s thesis was performed during the fall of 2006 at Cloetta Fazer AB in Ljungsbro. Cloetta Fazer is the market leader in Scandinavia of manufacturing confectionary and chocolates. The purpose of the project has been to identify causes that impact the quantity of waste in production as well as a cost/benefit analysis of the solutions that can reduce the problem of production waste.The work includes four production lines that are individually designed depending on what kind of product that are produced on the line. By using qualitative and quantitative methods such as focus groups, interviews and observations data has been collected.

This bachelor thesis has the purpose to visualize and document the air movementsprovided by different ventilation principles in an operating theatre. The visualizationwill be made as simple as possible in a physical model. The model and thedocumentation should be able to use in educational purposes.The study is based on the two most common systems for airflow, currently used inoperating theatres. The first principle is displacement ventilation in which the air issupplied at low velocity along the floor. The second principle is vertical parallel laminarairflow in which the air is compressed like a piston from ceiling to the floor.A review of literature resulted in the choice of size, design, and scale factor for themodel, as well as choices of ventilation principles and airflows.

This degree project has been carried out by Oscar Adolfsson and Marcus Blomqvist, during the spring of 2010, both studying to become Bachelor of Science in Innovation and Design Engineering, at Karlstad University. The degree project includes 22,5 credits.The work is done on behalf of Etac Supply Center AB in Anderstorp. Etac is a company developing and manufacturing home health care products, with operation in Sweden, Norway, Denmark, England and Germany, and with sales worldwide. Bo Lindqvist, R & D manager has been the contact person at Etac.During the project the students has had a workplace at Semcon Caran AB in Karlstad. Semcon has also been helpful as a sounding board.The objective of the work has been developing a new, wall mounted shower chair, assigned for persons with difficulty to stand up while showering.Etacs requirement of the shower chair is that it should be able to support a user with a weight of 100 kg, the chair shouldn?t have any outrigger, optional should be armrests and backrest.

Södra Cell Mörrum is one of the five paper pulp plants that are included in Södra Cell, and the paper pulp that is produced here is not only sold to Swedish paper mills. Most of the paper pulp is exported to different countries in Europe. In the manufacturing process the plant needs different kind of process water and there are guideline values for how much copper, iron and sodium this water is allowed to contain. Analyzes of this water is in the current situation done with an atomic absorption spectrometric instrument (AAS-instrument) with a flame. Measurements done with flame-AAS of samples that have concentrations near the guideline values for copper, iron and sodium, are not reliable. The reason for not being reliable is that the quantitation limits of these metals are higher than the limit values.

Slöseri är ett stort problem på byggarbetsplatser. Ett koncept där minimering av slöseri ärcentralt är Lean-manufacturing. Detta arbetes syfte var att utreda hur förbättringsarbeteanvänds på byggarbetsplatser. De befintliga systemen för förbättringar analyserades ochförslag till förbättringar gavs.Genom intervjuer undersöktes hur förbättringsarbete sker på byggarbetsplatser.Egenkontroller och arbetsberedningar användes som kvalitetsarbete på arbetsplatserna. Detvisade sig att de inte har något system för förbättringsarbete.