Bakgrund: Self-efficacy, en persons tilltro till sin förmåga, är en faktor som påverkar hälsobeteenden såsom fysisk aktivitet. Exercise Self-Efficacy Scale mäter denna egenskap genom självskattning, men har inte utvärderats för personer med schizofreni.Syfte: Att omarbeta Exercise Self-Efficacy Scale för personer med schizofreni.Metod: Deskriptiv design med psykometrisk prövning av den omarbetade Exercise Self-Efficacy Scale. Första delen av studien bestod av fokusgrupper med patienter och personal på en psykiatrisk öppenvårdsmottagning för patienter med psykossjukdom. Utifrån resultatet av dessa utvecklades Exercise Self-Efficacy Scale ? Schizophrenia Version.

The system tungsten-oxygen has potential of being suitable for decorative coatings since ceramic coatings are often hard and wear resistant, and since modulations in oxygen content or incorporation of small ions could give bright colours. The aim of this report was to investigate the relationship between process parameters and  the properties of the films, with the wear resistance being of special interest.Samples with tungsten to oxygen ratios in the range of 100:0 to 25:75 at% were made using reactive sputter deposition, either with constant gas flow, or gas flow controlled by optical emission of the plasma. The hysteresis of the system, which means that a certain gas flow will cause different pressure and/or target voltage depending on in what way the flow is reached, makes it interesting to control the process where the system makes the steep change from metallic tungsten to ceramic tungsten oxide. This is difficult and thus requires precise control equipment.The samples were analysed using X-ray diffraction, X-ray photoelectron spectroscopy and an empirical wear test suitable for small components like cell phone cover for example, in order to characterize the structure, composition and wear resistance of the coatings. The results could be divided into three groups: (I) tungsten-like, with very low oxygen content; (II) mixed phase and (III) tungsten oxide like, with oxygen content close to 75 at%.

According to a decision of the European Commission, measures are to be taken to reduce the use of energy in the EU. The goal is to reduce it by 20 % compared to the current use. This shall be done to the year 2020 (European Commission, 2011). One industry that use large amounts of energy is the construction of buildings which account for almost a third of the energy use (Brogren, 2012). The major part of the energy that is used in the construction industry is not used when the buildings are built, but rather during the rest of their subsequent lifetime.

In Sweden the latest curriculum, Lpo 94 was released in 1994. This document revolutionized the teaching profession. The school system was changed from a governmental control into a communal control. The earlier curriculums were controlled by rules; Lpo 94 is controlled by aims. This has led to a big spectrum of teaching styles which all of them agrees with the Lpo 94.Our purpose with this report is to illustrate two different leadershipstyles regarding the subject Swedish.

Problem The culture sector is characterized by qualitative goals which raise questions such as how do you measure culture and what is ?good? culture? Both the goals and the measurements tend to result in subjective judgments, which according to the theory make result control inefficient. Yet, result control is frequently used in the culture sector; which leads up to our research question: What characterizes the problems of result control in the culture sector?Purpose The aim of this study is to make a survey of how the Gothenburg Opera works with result control and follow-up. By defining how it tackles the different problems, which could arise with result control in a non-profit organisation, we aim to map how the problems regarding result control are characterized in the Gothenburg Opera.

This report describes the development of a system for controlling documents. The report starts with a problem description which the company wants an intranet-based solution for. The report then continues to describe the development phase for the different parts of the system which results in a complete system. The company that wanted this system is called Orbit One and is located in Ronneby, Sweden. They have had a problem with old documents circulating in different versions and in different binders.

Det finns i management control-litteraturen en efterfra?gan pa? studier som tar ett helhetsperspektiv pa? styrsystem (Management Control Systems, MCS) och som fo?rklarar hur dessa system bidrar till effektivitet hos organisationer. Utifra?n ett contingency-synsa?tt underso?ker vi i denna studie hur kulturell styrning och prestationsma?tning som delar av MCS, tillsammans med den kontextuella variabeln osa?kerhet i omgivningen, pa?verkar hur effektiva organisationer a?r. Vi antar en systemansats och o?nskar studera relationen mellan fler variabler, och da?rfo?r tilla?mpas en klusteranalys da?r datamaterialet delas in i grupper med liknande karakta?ristika.

This is a report written for an examination project C-level, on the subject of energy. The examination project is a product of the FVB Sweden AB (district heating bureau). It started with a meeting with Stefan Jonsson FVB Sweden AB, were he explained the content of the project, and from this a presentation of the problem was made. The problem that needed to be solved was how they could control the valves in the system to provide heating to everyone in the system. The valves are often oversized so the pump in the heating plant would have to be enormous to be able to provide enough flow to be sufficient, if everyone in the system had there valves fully opened. I came up with two solutions to the problem, one was a wireless network that could keep track of the valves and the other solution was an extra sensor that was placed on the radiator.

The thesis presented in this report has been made on behalf of Scania and their basic frame design department with the subject to solve an implementation of a weight sensing system in the chassis. The system is supposed to be implemented in the seat springs, and the reason for this is that all the force will have to go through the weight sensing transducers. With all the force going through the transducers the weight sensing system will not be sensitive for the differences in tolerances from manufacturing. The transducers could be pre-calibrated to avoid a calibration of the whole vehicle after it?s completed from the manufacturing line.Weight sensing systems is today a reality in trucks with air springs.

This thesis describes a system for dealing with free surface fluid simulations, and the components needed in order to construct such a system. It builds upon recent research, but in a computer graphics context the amount of available literature is limited and difficult to implement. Because of this, the text aims at providing a solid foundation of the mathematics needed, at explaining in greater detail the steps needed to solve the problem, and lastly at improving some aspects of the animation process as it has been described in earlier works. The aim of the system itself is to provide visually plausible renditions of animated fluids in three dimensions in a manner that allows it to be usable in a visual effects production context. The novel features described include a generalized interaction layer providing greater control to artists, a new way of dealing with moving objects that interact with the fluid and a method for adding source and drain capabilities..

A district heating plant has the advantage that it can take advantage of the waste heat from industries and use of cheap fuels to produce heat. But for the long term is competitive requires that energy is also saved in district heating plants. One way to save energy in a district heating system is to increasing cooling to the return temperature. This leads to less power needed to drive the distribution pumps,  and that more energy could be extracted from the same amount of fuel by an improved flue gas condensation.In Karlskoga the return temperature into the district heating plant is high. They would therefore reduce the return temperature in order to extract more energy from the flue gases.

This master thesis holds a modelling in Simulink for a physical model of a main battletank tower, a three-phase induction motor and some mechanics. The aim of this work is to connect an earlier project at AerotechTelub, named StabSim to another called Eldris. In StabSim it has been made a Simulink model of the align and stabilisation system in a main battle tank 122 and in Eldris it has been build a physical model of a main battle tank tower. In this thesis the models that differs between Eldris and a real tower is changed in StabSim, and the parts that only exist in Eldris is added, for example a torque generating system which purpose is to make the model to behave like a real tower in control application, although it only has half the inertia as a real tower. The thesis even includes proposing a calculation of the torque that the torque generating system will actuate at the model..

Material handling is a term that includes all kinds of handling of material from a raw product to a finished one. ABB is active in the following segments; foundry, packaging and palletizing, metal industry and plastics industry.The demands for efficiency and reliability have been set very high in the industrial sector. Optimizing of the material handling will give the company higher cost-effectiveness. Around the robot there are different kinds of material flows, to optimize the cycle time, consisting of carriages combined in different ways.Motion Control is a complex system with main functions such as; positioning, synchronizing, indexing and more. The products in the system need to cooperate to make these functions possible therefore integration of motor- and servo products are important.

The accounting scandals that have attracted attention in recent years have led to internal control becoming a more central part of business activity. Doubts about what firms actually do have increased, all caused by the attention of accounting scandals. To counter this, frameworks and laws evolved and gained a significant role in the organization and its surroundings. The aim of the present study is to find out how four companies in the Kristianstad region are working to ensure its internal control and how they work to minimize risk and reduce uncertainty. We have used a qualitative method and interviewed a person in a senior position in each company.

This thesis examines if commercial-of-the-shelf (COTS) systems meet the needs in different types of organizations. This was investigated through a case study of a COTS system. The system is built for contact centers and used in different types of organizations. Contextual inquiries with users from six different organizations were held together with interviews with stakeholders of the system. This gave an understanding for how the system is used and the needs to be met in the different organizations were recognized.