This report is made as a literature review, focusing on the work done to increase understanding of efficiency in the categories of substations and secondary heating systems, with respect to the deviation from the theoretically possible cooling off in the distribution network as well as the economic benefit that appear. The main purpose of a considerable part of the literature used in this report addresses the issue of identifying individual causes of reduced cooling in district heating systems. These literature resources have been compiled and summarized as part of the report.The technology of district heating is associated with benefits such as better use of the energy in a fuel. This is the case of cogeneration plants where serial generation of electricity and thermal energy increases efficiency compared with the parallel generation where heat is generated locally and electricity is generated centrally. Serial generation thus allows for lower primary energy demand.

In Sweden, a big part of the energy use is used in the housing sector. Political goals and targets are set up which the housing sector needs to work towards. Apartment buildings are a major part of the housing sector in Sweden and therefore reduction of energy use in these kinds of buildings are key to lower the energy use in Sweden. But there are not only political incentives to reduce the energy use. Some energy?saving measures are directly profitable and should thus be performed.

This report, written by Ma?ns Ridze?n and Jonas Stenberg, presents the thesis carried out the spring of 2012. The authors met the first time in 2008, when they started their studies at Uppsala University. Since then they have completed various projects, both within and without the university. This study is based on a theory that was first conceived when Jonas Stenberg did his internship in the summer of 2010.

The purpose of this essay is to draw attention to the obstacles that affects the internal trade of waste within the EU. The essay doesn?t in any way encourage pollution or illegal handling of waste but unfortunately there are large profits to be made from illegal destruction and recycling of waste and especially hazardous wastes. Therefore the dependable companies handling waste must access a market with fast and flexible (but predictable) regulations as well as lower transaction costs to help make the environment better and encourage a strive for increased recycling. There are examples where some waste only can be sent to a land-fill within the country but could be recycled in other EU-countries.

The evaluation of the function of the feeding of sheep herds is suggested to involve the work effort, the fulfilment of the nutrient needs of the sheep and the feed waste. Mechanisation of the feeding can be very simple or include high degrees of mechanisation. Three different farms, representing different levels of mechanisation are presented. Descriptions and analysis of the feeding systems including mechanisation, work effort and estimations of the feed waste are made on each farm. The herd with the most advanced feed mechanisation included a rolling feed band and mix wagon. The other farms were partly or little mechanised including ad lib feeding from big bales and manual distribution of hay and concentrates. The most mechanised farm was able to feed a large herd of sheep at a low work effort and little feed waste. However, the investment in machinery has to be weighed against the improved efficiency.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

The production costs have steadily increased within the construction industry during the 21st century. Voices are raised meaning that the construction industry is too unsuccessful in making the production more efficient and to develop it?s way of working. One way to deal with the production costs is to minimise the waste, with waste meaning activities that doesn?t add value to the finished product.

According to recent statistics the construction industry is responsible for the largest waste discharges of both dangerous and non-dangerous waste, when disregarding the "non-dangerous" amount of granite waste produced by the mining industry and the waste produced by the pulp and paper industry. Preventive work within waste management is an ongoing practice so to be able to reduce negative environmental effects. One of the most common actions for the companies to take is to separate the different kinds of waste from one another at the construction site. Although by working with the problem in earlier stages of the process a large amount of the waste could already have been reduced.Companies in the construction business that are actively working to decrease environmental impact in their operations often use an EMS (Environmental Management System). By using environmental management as method the company can manage their environmental work so that actions can be taken where they are needed the most.

To achieve the requirements to decrease emissions of greenhouse gases by 20 % by 2020, Swedenneeds to increase its use of bioenergy. In doing so it seems natural that those who already haveaccess to large amounts of biofuels in the form of by-products such as straw, wood chips anddigestible materials take advantage of these assets locally. By combining production of heat withpower production at the farm it may be possible to not only reduce the direct use of fossil fuel forheating but also reduce energy costs.The purpose was to simulate different cases of using a small scale biofueled combined heat andpower plant for farm-based systems. A MatLab-model was developed and used to draw conclusionsabout the costs for production of heat and electricity with different conversion technologies.The model uses climate data to simulate the variations in heat energy demand on a day-to-day basis.The given heat demand is the base of the simulation and from this the possible electric output iscalculated. This study has focused on the impact of the following properties: electric-, heat- andtotal efficiency, fuel, fuel price and specific fuel requirements.

The world?s growing need for energy together with a desire to ward off the worst consequences of global climate change has resulted in a never seen desire to invest resources in renewable energy sources. Biogas production through anaerobic digestion is one of those growing energy sources. In Sweden there are over two hundred plants that uses this biological process to break down organic substances while producing carbon dioxide and the energy-rich gas methane.This master?s thesis has focused on development of the mixture of different organic substances that is treated at a specific plant, namely Mosserud biogas plant.

Thermia Värme AB is one of the market leading manufactures of heat pumps. In order tomaintain this position, the company wants to improve the vibration characteristics of theirproducts. The aim of this thesis is to develop product design changes that lead to a reductionof vibrations in the heat pump Thermia Diplomat 8.The main cause for vibrations in the system is flow pulsation and mechanical forces inducedby the scroll compressor. Vibration is transmitted through the compressor piping and receivedby the heat exchangers, from where it is further transmitted to the connection points for theradiator and heat source circuits.A number of design changes in order to improve the vibration characteristics have beenevaluated through calculations and practical experiments. The changes have included thecompressor and heat exchanger mountings, the compressor suction and discharge line pipingand also pulsation dampening.The results of the experiments show that the vibration levels in the connections for the heatingand brine circuits can be decreased strikingly through changes in suction and discharge linepiping.

During installation and operation of a geothermal heat pump system leakage of an antifreezing agent can appear in a borehole and leak out in surrounding groundwater. To guarantee high quality drinking water for generations to come Sweden has dedicated some areas as water protection areas. The local authority gives permits for the installation of heat pump systems within water protection areas. Before giving a permit the local authority makes an evaluation of the risks involved in installation and operation of the system within the area. By keeping a certain distance between the protected object in the area and the heat pump system the risk of polluting the protected object with an anti-freezing agent can be reduced.This thesis makes a comparison between three different methods of calculating an appropriate distance between the protected object and the heat pump system.

Outside of many Swedish households today, you will find a typical green wastecontainer. This container has not changed since its introduction, despitecomplaints about foul-smelling and its impractical system. Even if the system usedtoday, still is the most optimal choice, there is a lot of newly developedalternatives out there.Its purpose is to get a broader perspective on how a waste management systemcan be developed into a working, land efficiently and aesthetically pleasing systemof humans and the environment in a small residential area.The authors treat the residential area of Jära, Ekhagen, in Jönköping, which ismanaged by JM AB as a problem area in regards to waste management.The issues raised by the authors are the different waste management systems usedin the corresponding areas of the world, how to apply technical andenvironmental as well as the waste management facilities from financial aspects.In the process, the methods used were literature reviews, case studies and aninterview. The case study was done through a modeling of waste managementsystems in the area Jära and an interview was conducted with the company Envacworking with vacuum systems. Studies have been made by different systems n theareas around the world.The results show that using directives and guidance will reduce the environmentalimpact done without replacing the traditional system.

The building sector accounted for around a fourth of the total energy usage in Sweden in year 2010 (Energimyndigheten, 2012). Therefore it has become very interesting to achieve a lower energy usage in residential buildings. One way to achieve that is to build so called passive houses. By being very well insulated and have low leakage through the walls, they can reduce the energy usage for heating with a substantial amount. The first passive house was built during the 90?s in Germany; and in Sweden the first passive house was built in Gothenburg 2001.

A district heating plant has the advantage that it can take advantage of the waste heat from industries and use of cheap fuels to produce heat. But for the long term is competitive requires that energy is also saved in district heating plants. One way to save energy in a district heating system is to increasing cooling to the return temperature. This leads to less power needed to drive the distribution pumps,  and that more energy could be extracted from the same amount of fuel by an improved flue gas condensation.In Karlskoga the return temperature into the district heating plant is high. They would therefore reduce the return temperature in order to extract more energy from the flue gases.