The study aims to reduce energy consumption in apartment buildings where individual metering and charging of heat is applied. The aim is to develop planning and design for individual metering and charging in apartment buildings.The study is based on literature review, interviews and case study that include analysis of existing documents. Interviews were carried out with the property developer and the involved consultants who planned the apartment building Yasuragi. To investigate the differences the condominium association has noted in heat consumption between flats, the debit values of the heat were used to discern which houses that were furthest from the average consumption. On these flats there were temperature measurements and thermal photo shoots made for discriminating behavior and possible construction techniques which could be the explanation for the heat spread.Boverket shows that the consumption of heat can be reduced by 10-20% after insertion of individual metering and charging in an apartment block.

The management of water resources and waste water varies between the countries of the EU. For many years, a large part of the water in Europe has been contaminated by, among other things, insufficiently treated waste water and emissions from agriculture. The EU Water Framework Directive 2000/60/EC and the Urban Waste Water Directive 91/271/EEC are intended to harmonize fresh-water management and waste water management within the whole EU, aiming at safeguarding drinking water of good quality and a high quality of all water within the EU today and in the future. There are however some problems concerning the waste-water directive. One problem is the huge investment needed in Slovakia to fulfil the demands of the waste-water directive for waste-water management in larger communities (with more than 2000 inhabitants).

The energy consumption continues to increase as the use of electronics and energy consuming equipment increases. The use of fossil fuels has to be phased out for this to be sustainable in the long run while the use of renewable energy continues to increase. A renewable energy source is solar energy but the production of heat and electricity are today very expensive compared to other energy sources and an important task for the solar energy market to grow is therefore to minimize the production cost of the solar collectors while increasing its efficiency to produce heat and/or electricity. One way to convert solar energy into heat is by using solar collectors and electricity can be produced by utilizing the produced heat, or by applying solar cells.This thesis aims to recommend a reflective material for the next generation solar collectors from Absolicon and to recommend a commercially available coating for the receiver tube of the solar collector. A market study has been carried out to investigate the cost-related aspects along with the optical and durable aspects for the optical material of the solar collector.

In Sweden, there are limits to how much leachable substances waste must contain in order to be deposited as hazardous waste. Fly ash from waste incineration often end up over the limit, mainly due to the chloride content. Fly ash is therefore often deposited abroad. The purpose of this study was to investigate the possibility to handle fly ash locally. To clarify how the law is applied, environmental reports and permit documents from ten waste sites with permission to deposit fly ash were studied.

All over the world the waste from human society is causing problems. In developing countries, large cities are polluted through huge amounts of wastes and people are forced to live very close to open deposits. Lima, capital of Peru, is no exception. The countryside in Peru has also a great challenge to face concerning the waste issue. Children and adults suffer from infectious diseases and contamination of the nature occurs as well. One solution to handle organic waste is to compost, which means a controlled decomposition of organic waste under aerobic conditions at certain temperatures.

Finnhamn is a group of islands that are located in the middle north part of Stockholm?s archipelagos. On the main island Stora Jolpan there is a camp called Sommargården, which consists of eleven different buildings in various sizes. The assignment given by the Archipelago foundation (Skärgårdsstiftelsen) is to analyze if it?s benefited to replace Sommargårdens current heating system that consists of electricity radiators, with a more energy efficient heating system. This research is done with help of the literature review and a visit to Finnhamn in order to map Sommargården?s current state and its energy usage.

This thesis aims at determining the heat losses in a property vent stack and its roof valve. Upon request of a company, the vent stack is analysed for possible heat recovering solutions to be implemented, while relining of the drain system is executed and with a suitable payback time for the economic investments. The heat loss calculations are based on data for properties that are located in the Stockholm region, but also easy to change depending on the situation. The calculations are done on pipes made out of cast iron, which still is the most common type of drain pipe in Sweden, and these are the pipes that relining is usually made on. The calculations that needed to take several variables into account have been done in MatlabR2014a and the thermos dynamical properties that were used in those calculations have been extracted from EES.Three different types of heat losses in the vent stack have been taken into consideration in this thesis.

In June 2006 the Swedish government decided that the use of energy in buildings should be reduced by 20 percent until 2020, compared to the level of energy used in 1995. To contribute to this goal, the real estate company ?Eskilstuna Kommunfastigheter AB?, set up own goals for their buildings. In 2009, the goal for schools was to have a maximum energy use of 118 kWh/m2year for heating and hot water.The school ?Hållsta skola?, just south of Eskilstuna, exceeds the limit since it used 270 kWh in 2008.

Cost allocation ? a study of how Swedish energy companies allocate costs between electricity and district heating in a combined heat and power plant District heating is today the most utilized alternative for heating in Sweden. In a combined heat and power plant (CHP) electricity and heat are cogenerated. The environmental and economic advantages with this kind of production are high. A problem in a CHP-plant is to allocate costs between electricity and heat since both products are generated in the same process.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

AbstractClimate and environmental issues are of paramount importance. Researchers agreethat we must all contribute to a reduction of gases that contribute to climatechange. Energy consumption must decrease within all sectors and the promotionof renewable sources of energy must be introduced.Each sector should aspire to decrease its energy consumption. Energyconsumption is strongly linked to waste gases that contribute to climate change.Passive houses are a part of the construction industry's methods to attain energyconservation.Passive houses are derived from low energy houses and super insulated houses. Apassive house is intended to obtain heat from the inhabitants and through theiractivities.

This master?s thesis was performed during the fall of 2006 at Cloetta Fazer AB in Ljungsbro. Cloetta Fazer is the market leader in Scandinavia of manufacturing confectionary and chocolates. The purpose of the project has been to identify causes that impact the quantity of waste in production as well as a cost/benefit analysis of the solutions that can reduce the problem of production waste.The work includes four production lines that are individually designed depending on what kind of product that are produced on the line. By using qualitative and quantitative methods such as focus groups, interviews and observations data has been collected.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

Efficient energy use in the housing sector is crucial for achieving a sustainable society. The expansion of this sector only represents a fraction of the existing houses, hence it?s within the existing houses the potential for energy savings lie. This potential has been analyzed in order to determine if it?s possible to cut the current energy demand in half.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.