This thesis describes the redesign ofequipment designed for drying bags thatis used in Fresenius Kabis´manufacturing of their nutritionmedicine in Uppsala. The need of thistask arise during the start of thedevelopment of a new packaging line werethis equipment were meant to be used. Anevaluation of the bagdryers capacity andcapability was necessary.The work started with gathering ofinformation from suppliers of the usedcomponents and from the responsibleengineers for this equipment. Aneducation to learn how the equipmentworked and how to operate it were taken.That was followed by the creation of astudy plan were the tests were plannedto test different parameters effect onthe drying result and to see if thebagdryer managed to handle the bags ofthe correct format in the pace that theequipment should be designed for.The test results detected a need ofdesigning a unit with a function thatholds the bags in place while passingthrough the dryer in order to attainhigh quality results. The results werelater used for optimization of thedesign.

The purpose of this study is to find datable interstadial sediments in the core area of the LateWeicheslian ice sheet extent. Based on geomorphological evidence, three coring sites wereidentified close to the Ultevis plateau in Norrbotten, northern Sweden. Sediment coring wascarried out in two pre-Late Weichselian stream channels and in a sediment basin. Stratigraphyfrom one of the sites, a 100 meter wide meltwater channel, was chosen for further analysis. Thestudied core was 5,93 m long and ended in a lower till unit.

The present study concerns a concept development of a product idea that Bengt Magnuson, associate professor, had when a heavy storm caused a widespread power failure of long duration. With a basic power-producing unit one should be able to get through a power loss. The product could also be useful for other tasks if different modules are connected, e g grass mower or snow-blower.According to the product idea the basic unit will be able to produce electric power enough for a fridge, freezer, TV, and a few electric lamps. Normally the basic unit can be used e g as a mower, when such a module is attached. An increased number of tasks would make the contraption useful and tempting for those who do not own an electrical power set in reserve.

 The purpose with this thesis was to develop a designguideline which will simplify the development of new products that will be laser welded. The need for this thesis has come forward from the quality problems that Volvo Construction Equipment, Components Division is having with their laser welding manufacturing unit. The reason for the problems emerges from the bad communication between the development unit and the manufacturing unit within the company when the products produced today was developed. This resulted in products that were hard to and in some cases almost impossible to weld. To avoid these problems from occurring again it was needed to gather the experiences within this area and compile it and present in a brief a pedagogical manner. The information for the groundwork of our results has been gathered by interviews of several key persons in Volvo Construction Equipment, Components Division.

This study is based on interviews with four managers in public elderly care and four managers in private elderly care. The aim of this paper is to examine how these managers are experiencing their leadership in relation to conflict management, and if the managers leadership differs depending on private or public elderly care. Leadership and conflict management are theories that have been used in order to analyze the empirical findings. Previous research that has been used in the study concerns ?leadership/leadership styles?, ?conflict management?, ?to be active in the private/public elderly care?.

This work has been done to develop a plan for a future dairy barn at theGästgivaregården and to show the space needed for cows and replacement heifers. Itwould also show the storage that will be needed. The design was largely based on resultsfrom studies on six different farms, but also the facts that are taken from research papersand articles in order to compare theory with practice. Because some farms only whereinterviewed by phone I have used a query form to obtain comparable resultes.The aim is to build a new barn with Automatic milking. I've drawn a milking stable for120 milking cow and replacement heifers with the capability to house up to 140 milkingcows if the farm would expand in the future.Calculations of feed amounts and space requirements have been made to see how manyhectares are needed to supply the cows and replacement heifers with feed and to knowabout what size of storage space is required.The investigations made in this writing are to answer questions about the AMS-unit`sposition and how to best maintain a good health status in the herd.

Many research reports mention the fact that a huge number of all system development projects never reach a successful ending; with other words never fulfil formulated goals. By identifying and forming success factors (and in some aspect risk factors) that the project manager in practice can use, this study may be seen as a step in the direction towards minimising the high number of failed system development projects. The purpose of this research report is to investigate how a system development project, where the development process is based on a specific development or process model (in this case the Waterfall model), can and should be driven. I aim to clarify what is demanded of a project leader for the specific development process and give an account for which eventual leadership qualities that can be well suited for given situation in relation to the need for technical competence. Among other things the project manager should inspire confidence, drive, be a decision maker, engage and own some form of basic knowledge in the field of system development.

MYDATA automation AB is one of the leading companies in development of surface-mountingtechnology and stencil free solder paste applications. MYDATA?s MY500 is a jet printerdesigned for solder paste application on printed circuit boards. The jet printer contains a cassettewhich consists of a holder and a cartridge. There is also a calibration unit which monitors andcalibrates the application of solder paste.

This paper describes a method for wireless energy transfer via near-field electromagnetic inductionthat is inexpensive, simple and can be applied to almost any type of system, regardless of size andenergy demands.The method uses a primary unit consisting of an oscillator, amplifier and inductive coil thattransfers energy to a secondary unit consisting of a coil, rectifier and voltage regulator. Two typesof oscillators and several amplifier designs were realized and evaluated together with a multitudeof flat coils of both monofilar and bifilar type.The results show that it is important to use an oscillator whose frequency is dependent on theinductance of the connected transmission coil, such as the Colpitts oscillator. This is preferable toan oscillator with a preset frequency, such as a Schmitt-trigger oscillator..

The change in course recently taken by the Swedish Armed Forces results in an increased use of equipment, and thereby increased requirements of preventive maintenance. This paper aims to examine the current responsibilities for preventive maintenance in an army unit. The intended effect of this examination is to disclose possible flaws, and to help make routines for preventive maintenance more effective.The questions asked in this paper are;Who, in an army unit, is responsible for the routine maintenance?When is this responsibility valid?What demands does the technical service have on responsibilities for the routine maintenance?How are these demands met?How ought to be responsible for the routine maintenance?To answer these questions the author has chosen to use a descriptive method to show the current facts. A theorizing method is chosen to, from described facts, clarify the demands of the technical service on routine maintenance.

Shock absorber units play a key role in establishing the driving dynamics and performance of automobiles. Öhlins Racing has manufactured high-tech automotive shock absorbers for over 30 years. Öhlins Racing?s advanced technology has contributed to over 200 world championships in automobile racing. Öhlin?s manufacturing process has long utilized automated fluid filling equipment during the final shock absorber unit assembly stage. The filling process consists of vacuum pumping the shock absorber unit and subsequent transfer of fluid. Vacuum pumping is necessary to remove residual air from the shock absorber unit prior to initiating the liquid filling stage. The presence of undesirable gases drastically compromises the performance of a shock absorber. The filling degree, defined as the final ratio of air to oil, is determined by the specific filling protocol as well as the specific equipment utilized.The current investigation aims to develop a viable technique to accurately determine residual air content in shock absorber units. If the filling degree can be appropriately quantified for a specific manufacturing process, then the air/oil ratio may be quantitatively related to shock absorber performance. The utilized measurement method must be completely integrated into the manufacturing process to guarantee shock absorber performance specifications according to the manufacturer?s standards. By utilizing the measurement method developed in this work, the manufacturing process, manufacturing equipment and product specifications can all be tailored to provide improved filling conditions.The developed measurement method provides accurate quantification of the filling degree under a wide range of processing conditions. The method establishes the relative quantity of air in the shock absorber unit by performing in-situ compressibility tests. The fill ratio can be controlled and varied by manipulating the vacuum pressure exerted during the filling process. Performance tests, however, indicate no correlation between filling degree and unit performance..

Denna uppsats syfte är att ta reda på om euron är en internationell valuta och omeuron kan konkurrera med dollarn om titeln som världens ledande valuta. Teori omvalutamarknaden, en valutas uppgifter och vad som avgör vilken valuta som användsinternationellt behandlas och för att kunna svara på uppsatsens frågeställningar (syfte)redogörs siffror på eurons internationella användning. Sådana siffror visar att euron ären internationell valuta då den används i valutans funktioner internationellt, men attdollarn fortfarande är den världsledande valutan utan att vara särsklit hotad i sinställning av euron..

In today's globalized world it is essential to achieve goal congruence within a multinational corporation despite the distances between the headquarters and subsidiaries. A case study has been performed to examine how control of sales units within a Swedish multinational corporation is achieved. Otley's framework has been used in the study to provide an overall picture of the control system where the analysis is based on five areas: key objectives and goal evaluation, strategies and plans, target setting process, incentives and motivation as well as information flows. To complement this framework, theories of convergence and divergence by Busco et al. have been used as well as theories of hierarchical control and self-control by Holmström.

Kitron had wishes to be able to test and measure how disturbance affects their vehicle electronic units before they have been verified by SP Technical Research Institute of Sweden in Borås. This work started with the writing of a demand specification together with Kitron for a product PSQS, Power Supply Quality Simulator, which can generate some test pulses according to a standard for electronic units to Volvos vehicles. A design proposal was developed with the help the demand specification and was verified with the help of simulations. All electric schematics was designed with the guide of the design proposal. The pulses realized in the works of this thesis are those which Kitron experienced that they have a need to test in their own premises and which are possible to generate with the means available.

This study was conducted at Glimek AB, a company that has chosen to decentralize its central storage unit in order to increase production efficiencies. The purpose of the study was to identify the problems in the production cycle that lead to the decision to decentralize the central storage unit, as well as identifying what the decentralization entails. The effects of the decentralization have not been analyzed in the study, and consequently neither financial nor production disadvantages have been considered.Appropriate questions were formulated based on the chosen underlying theories, and were asked to selected individuals with relevant knowledge. The study is based on the information that was gathered from interviews with management as well as staff within the company. In addition, supporting information such as flowcharts, drawings, orders and decision support documents were supplied by the company.