This study presents a methodology that enables the annual average power of a wind Turbine to be increased by automatically optimizing it?s airfoil, twist and chord dis- tribution. As a part of the study the software SiteOpt has been developed. This software connects the open source software XFOIL with the blade element momen- tum theory. XFOIL gives lift and drag coefficients which enable the blade element momentum theory to predict the power of a wind Turbine at different wind and ro- tational speeds.

The project contains a force analysis of the vertical axis wind Turbine Lucia's supporting arms and a measuring device to experimentally measure the forces is made. The forces between the supporting arms and the tower are calculated theoretically and then simulated by a computere. A measuring devise is then designed to measure the forces experimentally. The forces acting on the attachment between the supporting arms and the tower is primarily the centripetal force, gravitational force and the aerodynamic forces on the rotor wings. The maximum forces were theoretically calculated and is 13.38 kN along the x-axis, -0.25 kN along the y-axis and then 0.5 kN along the z-axis.

The jetengines of today are growing in complexity. Reliability for aircraft engines are of extreme importance, mainly due to safety reasons but also economical ones. This master thesis deals with faultdiagnosis in the Turbine section of RM12, the engine used in Saab/BAe's Gripen. Three different faults which can occur in the Turbine section was studied. These faults are: clogged fuel nozzle, hole in outlet guide vane and sensor fault.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions Turbine, a Kaplan Turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions Turbine, a Kaplan Turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

The power system modelled in this thesis work has been developed for simulationwhen e.g. the production in some part of the power system is changed. The powersystem has been modelled according to the swing mass of the system, the frequencydependency of the load and the Turbine governor. The model determines the systemfrequency, the period of regulation and the power exchange between the differentsubsystems in the Nordic synchronized system.In this model the system frequency is assumed to be the same in all different parts ofthe power system and the voltage conditions in the power system are neglected. Forthat reason power swings does not occur between different subsystems in the powersystem, which usually occur as a result of the swinging connection between thetransmissions line.

Wind power is one of the sources of renewable energy which has to be developed further in order to lessen our dependence on non renewable sources of energy. It's mainly oil and coal which have to be replaced by green energy. Wind power is already established in many countries, for example Germany, The United States of America and Denmark but it has to be continually developed and expanded to meet the needs of the growing energy consumption in the world. During the last few years many types of small wind Turbines have appeared on the market. These small wind Turbines are an alternative to the big wind Turbines or power generators which demand huge sums of investment money.A new target group can now buy the small wind Turbines in order to cover their own usage of electricity.

Arvika Fjärrvärme AB, a district heating company from Arvika, today cover 74 % of their total energy production with biofuel wich runs a 16 MW bioler giving process water at saturated liquid state.In recent years Vaporel AB has introduced a new tecnique that gives an external generation of steam after boilers. The concept is built on an adiabatic pressure drop of the saturated liquid in a so called Flashbox which makes a small part of the liquid to evaporate. The generated steam is lead into a Turbine where electricity is in a conventional manner.The purpose with this rapport was to do a basic study for the specific system at Arvika where it?s possible to see the potential production of electricity that follows an installation of a flasbox.The final goal was to introduce an economic analysis of a flashox installation at given conditions.To reach our goals we have created a model in Excel where we used the given conditions at Arvika Fjärrvärme to do our calculations. The model has been tested at three different states, of process water returning to potboiler, to be able to decide the optimal operation for the system at present.The studies have resulted in a pressure of the processwater at 14,5 bar (at) and a pressuredrop to 9,5 bar (at) in the flashbox.

Hydropower is the largest renewable energy source available in today's society. Operation and production is handled by high-tech electronics. This thesis is done on behalf of Statkraft Sweden AB who wants to explore the possibility of replacing the hydraulic cylinder with an electric actuator, generally as well as a case of a small power station on the river Nissan. Whether it is the chaplain or francis Turbine vanes are actuated by hydraulic cylinders. Because of Gustavsberg hydropower is inconstant operation, this report is based on power calculations, which are read and computed according to the available hydraulic diagram.

I detta examensarbete behandlas investeringsalternativ för småskalig vattenkraft. Arbetet som riktar sig mot Skellefteå Kraft AB:s anläggningar, har således gåtts igenom, vartefter kandidater lämpliga för en reinvestering tagits fram med passande tekniker. Vidare nämns om dessa tekniker är lämpliga för minskning av förlusterna vid storskaliga utskov. De småskaliga anläggningarna är fördelade på två åar, Rickleån och Åman. I vardera finns två kraftverk som behandlas i detta arbete, Fredriksfors och Sågforsen i Rickleån, samt Åman övre och nedre i Åman.

This is a feasibility study that examines various aspects of building a wind farm on Malmön in Norrköping. The feasibility study deals with interests of conflict, park design, electrical connections, production calculation, financial calculations and operating- and timetable.The report is divided into two distinct parts. First a theoretical part, which deals with conflicting interests, park design and electrical connections. Second a part with simulations dealing with production calculations, and financial calculations.Opposing interests are mapped so that problem areas can be found, and help put focus on the right places at a future environmental impact assessment (EIA). There are a number of areas where planners have to assess on an EIA, this thesis point on the most important areas.

This rapport contains an examination of the energy consumption of a kindergarten, which areas that have the largest impact on the energy consumption and what can be done to reduce those areas in ways that are relatively easy and profitable. It is also analyzed if it is possible to reduce the energy consumption from today?s consumption to a consumption that fulfils the demands placed on low energy houses by FEBY.The focus has been on reducing the energy consumption of the areas ventilation, heating system and hot water system, since those seemed to be the easiest ones to affect and since the building is quite recently built.There are different kinds of ventilation systems, at the moment the building have a CAV-system, which means that the ventilation is too high during large parts of the day. There are different ways to manage the ventilation system, for example presence detection, humidity sensors, CO2 sensors, temperature sensors and season adjustment. Many of those are in the end dependent on CO2 sensors to guarantee a good indoor climate, therefore the focus have been placed on this system.

This master thesis project at KTH is performed in the Mechanical and Aerospace Engineeringdepartment at University of Florida (UF). The thesis is a small part of a gas Turbine researchproject where a vapour absorption refrigeration system (VARS) and a high pressure regenerativeTurbine engine (HPRTE) are integrated together. The main objective is to build a computermodel of the VARS. The computer model is supposed to be used to analyse the off-designperformance of the VARS and should also be easy to integrate as a subroutine in a more complexsystem model. To model the VARS some knowledge of the absorbent/refrigerant mixture had tobe well known, in this case a mixture of ammonia and water.

Vattenkraftstationer, med dammar och Turbiner, utgör hinder för nedströmsvandrande smolt. Syftet med denna studie var att undersöka turbindödligheten för öringsmolt (Salmo trutta) vid två kraftstationer, de befintliga ytlänsarnas avledningseffekt och om effekten kunde förstärkas genom mörkläggning i form av övertäckning av kraftkanalen med en presenning vid turbinintaget. Utöver detta var avsikten även att undersöka om det fanns något samband mellan smoltgrad och smoltens förmåga att förflytta sig mot havet. I Emån i Småland fångades 46 öringsmolt som radiomärktes och sattes ut vid två kraftstationer och pejlades dagligen i sex veckor. Det var en större dödlighet vid den övre stationen än vid den nedre.

I dagsläget när intresset för miljövänlig energi ökar, ses den småskaliga vattenkraften som ett sätt att minska Sveriges import av energi. I Sverige finns det tusentals nedlagda kvarnar och små vattenkraftstationer som med små medel skulle kunna börja leverera energi. I Björkefall i Olofströms kommun finns en privatägd och övergiven kvarn. Detta arbete undersöker möjligheterna till en småskalig vattenkraftstation i denna åt Olofströms Kraft AB.Småskalig, vattenkraft, elkraft, generator, turbin .