With knowledge of how the southern Swedish forests have been affected by storms the past years, this study intended to find out which factors affect the storm firmness of a stand the most. The study was based on data from stands in the, by the storm Gudrun, affected area. The results of the analyses that tested the stand factors that influence the amount of storm damage to the greatest extent showed that the storm sensitivity of Norway spruce stands were largely due to previous management actions. The factors that could be controlled by thinning and had relevance of storm damage standpoint, according to the results were; the dominant height, volume, basal area weighted mean diameter and stand age at last thinning. In this study, these results are not as clear for Scots pine.

A storm in January 2005 felled 75 millions cubic metres of forest in South Sweden. Previous studies of wind damage in thinned stands indicated the importance of early thinnings. The risks of wind throw increased by increasing age and height of the stands. Previous studies also indicated increasing risk of wind throw along the strip roads. The aim of the present study was to investigate wind damage in Norway spruce stands in South Sweden in relation to time of the first thinning and different pattern of strip roads (width, length and direction).

Stands where pre commercial thinning has been ignored or inadequate often tend to have high stem density and low average diameter when they reach heights of thinning. In such stands, it can often be expensive to do a conventional pulpwood harvest as a first thinning. This study investigates the development of the stands and the economic outcome of forest fuel extraction, or a combined harvest as alternatives to the ordinary pulpwood harvest. Simulations in Heureka StandWise were performed for two thin and dense stands, which were constructed by data from the Swedish National Forest Inventory. The simulations show that the extraction of forest fuel in first thinning at an early stage can provide higher net revenue compared to conventional pulpwood harvest at the same time or later.

When Norway spruce is planted with large initial spacing and grows on highly productive sites in southern Sweden, a high proportion of the stems gets broad annual rings. The thinning programme carried out at the estate of Trolleholm aims to extract stems with too broad ring width. The 3-4 first thinnings are carried out as thinning from above, where only the thickest trees are removed. The internal distance may not fall below 5-7 meters depending on the number of thinning (short distance in young stands). The aim of this study was to examine the thinning model that is carried out at the estate of Trolleholm. A volume table is calculated to describe the model, and data is collected on temporary plots.

Overdue cleanings have for a long time been an important topic of discussion within the forestry sector. When stands that have not been pre-commercially thinned are reaching the level of commercial thinning, many problems occur in terms of decision-making and economical outcomes. These types of stands are commonly known as conflict-stands. The work was carried out partly as an interview survey towards representatives from the forest sector and the energy sector, partly as a case study of conflict-stands situated in Böksholm, north of Växjö and in Tönnersjö east of Halmstad. The criteria for the studied stands were that they had to be dominated by Norway spruce and be in a severe status of ?conflict?. The aim of the interview was to get an overview of the situation today, and also analyse trends in terms of conflict stands.

SCA has today almost 300 000 hectares of their forest land planted with lodgepole pine(Pinus contorta var. latifolia). Due to initial extensive planting in the 1970ies the area oflodgepole pine forests in the thinning age has grown rapidly from the end of the 1990ies.During the years 1996-2005 first commercial thinning of lodgepole pine at SCA took place.The goal of the hereby presented study was to investigate the growth and stability in thosefirstly-thinned lodgepole pine stands a few years after thinning. Furthermore, the objectivewas to investigate the relationship between stand stability and different stand parameters.Additionally, lodgepole pine stem quality was estimated.The study is mainly based on the data collected during an inventory project carried out atSCA in 2008. Altogether 91 lodgepole pine stands in northern Sweden were measured afterthe first thinning.

This study was conducted on a property with a thinning machine team. The purpose was to investigate in which machine, the harvester or the forwarder, that caused most damage to the trees in six different stands. Different factors, related to the damage frequency in the stands, were checked out. For example: basal area per hectare, thinning strength, tree diameter and the rate of production. The harvester drivers were also interviewed about how, when and why stem damages occur and how to minimize them. The study stated that 4.3 percent of the trees were damaged. Out of these 88 percent was caused by the harvester and the rest, 12 percent, by the forwarder..

Wind damages next to strip roads in 1st and 2nd thinning in Boxholm, Östergötland Anneli Fransson, SLU, inst f sydsvensk skogsvetenskap, Examensarbete no 108 Wind damage is something we are all familiar with since the storms Gudrun (2005) and Per (2007). Research about strip roads and wind damage is very limited. It is commonly known that the trees next to the strip roads more often fall whit heavy winds, and the purpose of this thesis was to verify this statement. Data was collected from first- and second thinnings at Boxholms Skogar AB, Östergötland. In first thinnings data was collected from both spruce and pine stands and second thinnings only data from spruce stands was collected.

The purpose of this report is to investigate and compare the difference between stand-thinning machines and strip-road thinning machines, and how they affect the stand on behalf of future growth, theoretical economic result, wind impact, snow pressure and density of stand. The investigation is regarding the first commercial thinning of pine stands, after pre-commercial thinning that was well conducted. The investigation area was located near Katrineholm, Sweden. The measurements that were measured were strength of thinning and amounts of wind throws, snow-breaks and hauling damages. The results that emerged, was that thinning with strip-road machines had a significantly higher strength of thinning over all, as compared with the stand- thinning machines (45 percent versus 30 percent). Comparisons between wind-throws, snow-breaks and hauling damages of the stand could not establish any significant differences between the two methods that were investigated. Conclusions, over all, were that if forest owners want to have more timber volume left for second thinning and final cut of the stand, the forest owners should choose the method with stand-thinning machines. From the point of view of gentle treatment of the stand and ground damages the choice should be the same. However, the method with strip-road thinning machines is the most common and accessible method in Sweden. Most likely it is the most economical way to manage the stand for forest owners in present time. If the method with stand-thinning machines is becoming more common in Sweden, it is suggested for forest owners to consider the stand-thinning method as a candidate for treatment due to economic aspects..

The aim of this work is to demonstrate how the net present value (NPV) at the time of the first thinning depends on the spacing after pre-commercial thinning, and show how net value from first thinning in same stand is influenced. This study is performed with models based on non-distant dependent growth models for single trees. Two different growth models have been used, one for cleaning (pre-commercial thinning) and one for thinning. The first one yields stem density distributed over diameter classes. In the second one, (the thinning model), it is possible to choose when thinning should be done, the thinning method, thinning grade and numbers of thinning.

Earlier attempts at mechanising pre-commercial thinning have been met with varying degrees of success. Most attempts have been based on techniques where residual stems are straddled. Early treatment is essential to limit damage on residual trees. One part of the present study is an evaluation of mechanised pre-commercial thinning using the new Vimek 404R. Vimek 404R is a fairly small machine that permits selective removal of stems, making it potentially suitable also for areas overdue for pre-commercial thinning. The study established the level of performance for the machine, as well as the improvement needed to make it an economically viable option.

This report is a thesis work for a B.Sc. in Forestry exam at the School for Forest Engineers, SLU. The work was an assignment from Sydved and the aim of the work was to investigate the economical output of removing understorey trees before first thinning. Four treatments were studied. - no cleaning before thinning - cleaning of all trees less than DBH 5 cm before thinning - cleaning of all trees less than DBH 7 cm before thinning - cleaning of all trees less then DBH 9 cm before thinning The result shows a decrease of the cost per m3 for the harvester with about 38% if all trees less than DBH 9 cm was cleaned before thinning compared with the un-cleaned area. At the same time the total net revenue increases with about 22%. .

The brown bear population in Alberta, Canada has been decreasing, while the Swedish has been increasing and all the affecting parameters are not known. This study examined the difference in these populations to see if an explanation could be found in differences between the forest management. The aim of the paper was to see if stand treatments had an influence of brown bears habitat selection in autumn in Sweden and how the results can be used in Alberta. This was done by analyzing bear positions in Sweden with forest data, and comparing forest management data for the study area in Sweden with forest management data for Alberta. The results displayed that mature forests over 60 years that have been commercially thinned are selected by bears rather than forests over 60 years that have not been commercially thinned in.

Silviculture in young stands in Sweden is below the mark concerning what has to be done in the forest, and it is time to solve the problem. The problem will not be solved only by the private forest owners, professional help is needed. Skogsägarna Mellanskog is one of four forest unions in Sweden who wants to play a role and take responsibility for forestry in the middle of Sweden. This academic essay is based on a market survey sent to 350 forest owners in the Örebro district. 186 of them answered the questions, giving a response frequence of 53 percentage. The purpose of the essay is to find the determining factors which will make a forest owner to find a collaborator when planning and carrying out the silviculture measures in young stands. The result of the survey shows that the forest owners are anxious about the price and the costs. The costs have a severe effect if the silviculture measures in young stands will be carried out or not.

The aim for the study was to examine a harwarder´s (combined harvester-forwarder) productivity when harvesting forest fuel in first Thinning stands that contains Lodgepole pine and calculate the economy of the harvesting work and estimate the quality of the thinning . The field study area where located near Arvån, about 15 kilometres south ?east from the city of Lycksele. The field studies were taken place in three different stands. All tree stands had the same tree age, but the tree species combination and the density varied.