One of today problem at IVT industries would be assembly of insulation on water cisterns. The element of assembly insulation on the cistern gets too elevated; hence one has to climb onto the stand the cistern is assembly on. This will increase the risk of work related injuries when there is a risk of falling down. It?s also rather strenuous on shoulders due to work with your arms high above your head.

This master?s degree project concerns the combination of a multi dwelling passive house with solar energy for the generation of electricity and domestic hot water (DHW). Different alternatives with either solar thermal systems or photovoltaic (PV) systems are compared with two reference alternatives producing DHW from electricity or district heating. The economical comparison uses a life cycle cost (LCC) perspective based on the present value of expenditures for investment, energy and annual operating and maintenance.The energy yields from the solar energy systems were calculated by hand and with simulation software. Calculation and dimensioning of PV systems were carried out with a software called PVSYST.

The need for snow-free surfaces at squares, bus stops, platforms, car parks and sports facilities increases and at the same time energy price rise and the environment is becoming a hotter issue. The construction of the ground heating systems often lack thermal insulation under the heating pipes, which means that the heat from the pipes not only warm up the soil surface but also heats the surrounding soil. The insulation also has more features, by insulating the risk of frost damage is minimized. The goal of this report is to demonstrate the large heat loss and energy costs in the absence of insulation under the heating system.The report begins with a scientific way to study and treating the soil heating system uses, and the theory involved. Furthermore it also deals with different routing principles of heat pipes depending on the facility.All calculations are made with so called finite element method (FEM), in COMSOL Multiphysics 3,5a, where models are created with different conditions.

Norconsult AB has developed a solarhousing concept, a house designed for the warm climate in the Middle East andwith large quantities of solar panels installed. The cooling system for the house was designed in an earlier report, the purpose of this thesis is to investigate the possibility of short and long term storage of thermal energy via an underground energy storage volume.Two different designs of the storage and three different filling materials have been integrated into a model to simulate different cases. The first design consisted of pipes installed in the ground, without insulation. The second design consisted of an insulated concrete box installed to prevent thermal energy from the surrounding soil to flow towards the lower temperature regions within the storage. The three different filling materials were dry saudi sand, water saturated saudi sand and the filling material used by the client for energy storage in Sweden.The results from the simulations show that neither of the designs, regardless of the filling material, managed to extract enough thermal energy from the house to the ground to uphold the demands of indoor climate.

År 1987 trädde en ny byggnadslag i kraft, Plan- och bygglagen(PBL). I och med den nya lagen minskade kommunens och byggnadsnämndens kontroll av projekteringshandlingar och besiktningar ute på arbetsplatsen. Efter lagändringen beror den slutgiltiga kvaliteten på en byggnad i större utsträckning på byggherrens och entreprenörernas egenkontroll. P.g.a. olika intressekonflikter inom kommunen, och att det kan förekomma starka kopplingar mellan byggherre och entreprenör, är det inte alltid självklart att kommunens tillsyn vid nybyggnation gällande till exempel egenskapskrav på energihushållning och värmeisolering utförs tillfredsställande.Med ovanstående i åtanke undersökte vi fyra flerbostadshus, två i Värnamo kommun samt två i Kristianstad.

This report provides a comparison between the products cellular concrete, foam concrete and LECA concrete. The questions to be answered during the work is how the cellular concrete stands up in cost terms to the existing competitors on the market, how the concrete products differ in design work, and in which situations the concrete varieties are preferred to use.Cellular concrete is a variant of ordinary concrete, with the difference that the ballast is exchanged from stone materials to expanded polystyrene beads (EPS). This substitution gives a product with higher insulation values but lower weight than ordinary concrete.The work was carried out by designing a survey which was sent to two hundred randomly chosen companies across Sweden, to see the building industry?s opinion of the product cellular concrete. The survey showed that cellular concrete was equals its competitors in terms of price, while the product was said to be more flexible, quicker and easier to cast.Then some of the companies, who participated in the survey, were interviewed to see more carefully, how the price, the workmanship and the time for casting and dehydration differed between the products.

As break downs of production transformers are costly and often result in long outages it is essential for reliability of operation that the transformers are manufactured to be robust. The aim of this M.Sc. thesis is to investigate if deviations should be made from the standard IEC 60076 ? Power Transformers in order to describe a robust large power transformer for procurement.The investigation has been conducted in three stages. In the first stage a definition of the term robust was developed in consultation with the client Vattenfall Vattenkraft.

This thesis work resulted in a template for how the thermal spray process can be controlled through robot programs. The robots today and their programs need to be replaced, therefore a new structure which can be matched with the new robot systems is needed. The work is limited to only concern structured programming on the new robots on Thermal Spray Centre (TC) with the programming language Rapid. The basic data for the program was retrieved from interviews with concerned personnel at TC, from studies on process parameters for thermal spray and from existing specifications at Volvo Aero Corporation (VAC). The thesis work briefly describes the process thermal spray and the four methods used at VAC.

The purpose of this master thesis is to investigate different types of measures for making buildings more energy efficient and to estimate their profitability. The calculations were performed with the building simulation program VIP+ and the evaluation of the profitability with the life cycle cost method. Furthermore, it was examined how losses in the distribution of secondary systems of district heating can be avoided. Options to replace district heating with a local district heating system based on bio-energy have been investigated. The possibilities of achieving more efficient thermal energy consumption and production for the chosen estate were also examined.The object of the study has been a residential estate with 133 detached houses in Uppsala, built in 1974.

When a combined heat and power plant produces heat and power it often faces a deficit of heat load during the summer or other periods of time. This heat is often unnecessarily cooled away or the power production has to be reduced or shut off. If it is possible to store heat from periods with low heat demand to periods with high heat demand one can get many benefits. Among these benefits are: increased power production, decreased operation with partial load, uniformly distributed load.To be able to store heat in situations like this long-term thermal heat storages are needed. In this thesis five different types of stores are presented: rock cavern storage, tank storage, pit water storage, borehole storage and aquifer storage.

This thesis work resulted in a template for how the thermal spray process can be controlled through robot programs. The robots today and their programs need to be replaced, therefore a new structure which can be matched with the new robot systems is needed. The work is limited to only concern structured programming on the new robots on Thermal Spray Centre (TC) with the programming language Rapid. The basic data for the program was retrieved from interviews with concerned personnel at TC, from studies on process parameters for thermal spray and from existing specifications at Volvo Aero Corporation (VAC). The thesis work briefly describes the process thermal spray and the four methods used at VAC.

This report compares two different types of insulation with regards to fire and moisture. The materials were tested for the company Fiskarhedenvillan AB, for a wall and a roof construction that the company currently uses in the establishment of Sweden's first certified passive house for international standards.Their current material, Rockwool, is compared to a relatively new material on the Swedish market called SEALECTION Agribalance sold by the company ISO Green AB. The material is a type of polyurethane insulation. This insulation material would result in a more efficient execution of the construction as it provides waterproofing and is applied more easily than Rockwool. From a fire standpoint, literature studies and discussions with fire experts led to results.

The climate changes that are occuring in the world have resulted in that the EU callingfor a 20 % reduction in energy consumption to the year 2020, to reach that goal theEU want the public sector to go forth as a good example. Västfastigheter owns andmanage the hospital buildings in the Västra Götaland region. To be able to reducetheir energy usage Västfastigheter has hired several consulting firms to chart out theenergy consumption on each hospital building. The biggest energy savings potentialhave been calculated and what the cost will be to perform each action. The energyaudit have been completed and stand as the decision basis for Västfastigheter?s choiceon which action packages that should be implemented.

The number of people in the world and the urbanization increases. This leads to a bigger need of space for the built environment, space that soon doesn?t exist. A large portion of humanity?s energy disposal is used for heating of buildings.

The survey aims to shed light on traditional and contemporary bottom floor frames, their construction and different insulating materials; mineral wool, wood shavings and charcoal. The purpose is to analyze and discuss the similarities and differences as well as the pros and cons with a focus on the construction and the different insulating materials. The work has been limited to comparing two different wooden floor frames. The first one is based on a real floor frame from an older building, this example is presented as the traditional floor frame in this study and are from around 1940. The other floor frame is presented as a contemporary floor frame and is based on wood building type descriptions and literature.