AbstractThis report intends through a case study to investigate if lightweight concrete isappropriate as main material in the outer wall of a seven storey residential building.A technical design is carried out in accordance with the definitions and requirementsfor passive houses, given by FEBY?s1 ?Demand specification for passive houses?.A literature review is also carried out for a comparison between regular bolt wall andlight weight concrete wall, with a focus on the safety of moisture.The lightweight concrete block used in the report is as a celblock produced by thecompany H+H Sweden AB.The methods used have resulted in compliance with requirements andrecommendations from authorities. Calculations of energy, noise and moisture riskassessment has been carried out.The work has resulted in the conclusion that the lightweight concrete itself is notable to isolate in the extent necessary to obtain chosen U-value of 0,1 W/m2 ° C,without getting to thick. Therefore additional insulation is needed. There are fewrelevant reference objects built with only light weight concrete.

This rapport is result of a project. The purpose of which was to design a circuit that is used in a heat glove. The heat glove is the technical aid which provides heat inside a glove.It is specially suited for old people who have problems with cold hands because of decreased blood circulation.There already was an old circuit in the glove that gives a constant current which develops heat from battery to glove through a circuit. The temperature is between 32 and 34 degrees.The problem with the existing circuit was to regulate the temperature. There is only on/off switch and there is no way to adjust desirable value of the temperature.In order to solve the problem the old circuit was investigated.

This thesis was carried out at Atlas Copco Tools and Assembly Systems. The purpose hasbeen to develop a design tool to be used for development of new electric motors for AtlasCopcos electric nutrunners. The focus of the thesis has been to increase productivity bydecreasing the power losses in an electric tool. The productivity is defined as themaximum number of tightenings a nutrunner can perform without becoming too hot.Before starting the development of this design tool an existing Matlab script, whichcalculates the losses in a slotless electric motor, has been studied and modified torepresent the real losses in a better way. The modification has been made by performingpractical studies of different losses and then adjusting existing parameters in the Matlabscript.Because design changes in one part of a mechatronic system can lead to a decrease inperformance of another part the choice of parameters that can be changed has been madeso that other parts of the system is affected as little as possible.A study of the existing tools efficiency during an entire tightening has been made toincrease the understanding of when and where the different losses appear and to comparethe modified Matlab script with the measured values.The design tool was formed so that it executes the Matlab script, that calculates thelosses, for a number of different design options and stores the alternative which producesthe least losses.

WSP building physics in Stockholm has certified the preschool Temmelburken in Bromma with the system of certification Miljöbyggnad. The rating of the building became BRONZE. In this thesis the preschool has been investigated with respect to the three areas: thermal climate, use of energy and improving of the level of certification. The thermal climate at the preschool has been investigated by a questionnaire survey and by measurements in order to do comparisons between the results from the two investigations as well as with the results of the simulations that WSP has done at the certification of the preschool. The differences between the results from the simulations and the questionnaire survey for winter as well as from the measurement performed with a comfort meter the 19th of March are concidered to be reasonably small since they give rise to the same rating according to Miljöbyggnad.   Operational data for the use of energy for the preschool have been obtained in order to do comparisons with simulations performed by WSP and Svenska Besiktningar AB. The comparison shows that the simulated values for the specific use of energy are lower than what the real specific use of energy would be for the preschool, since just the operational data for the heat energy is higher than the simulated values. At the investigation of the possibility of improving the level of certification it was found that the rating of the preschool can be raised from BRONZE to SILVER by improving the ratings of the ?thermal climate summer? and the ?daylight?.

This paper goes through solar energy and what uses it has. It is also a guide in the choice of solar collectors forthe real estate that I have drawn for the thesis work.Solar energy is a renewable source of energy from the Sun's light. Energy can be used to produce both heat andelectricity through solar collectors and solar cells. Some of the benefits of solar energy is that it is completely freeto extract, environmentally friendly and virtually maintenance-free. Disadvantages are that the technology isexpensive, does not cover the entire energy needs and takes a long time until it pays.

In the spring of 2014 Sweco Systems AB were commissioned to design a ventilation system for a newly built preschool in Linköping. Terms from the client was that it cost efficiency would cope with the energy demands that are placed on the building. The unit chosen was a cross-flow heat exchanger, and this work is to compare it with two other heat exchangers to see if a more energy and cost efficient could have been chosen. The heat exchangers that was chosen for the comparison was a rotating- and a counterflow heat exchanger. Simulations have been made to the different heat exchangers by the manufacturers.

This thesis work resulted in a template for how the thermal spray process can be controlled through robot programs. The robots today and their programs need to be replaced, therefore a new structure which can be matched with the new robot systems is needed. The work is limited to only concern structured programming on the new robots on Thermal Spray Centre (TC) with the programming language Rapid. The basic data for the program was retrieved from interviews with concerned personnel at TC, from studies on process parameters for thermal spray and from existing specifications at Volvo Aero Corporation (VAC). The thesis work briefly describes the process thermal spray and the four methods used at VAC.

The ?civilized? world is in need of fossil fuel in order to function. Hybricon AB is a company in Umeå that is developing a technology that hopefully can reduce parts of this need. They are currently testing their two electrical busses (with Hybrid backup) in city traffic on the roads of Umeå in cooperation with the county of Umeå.                               The busses are originally diesel-busses, but the diesel motor has been replaced with two electrical hub-motors with a power of 145 kW each that are powered by batteries.The batteries are charged at the end station after each route. In case the batteries should run low on capacity during driving, they can be recharged by the so called genset.

The automotive market is currently undergoing a historical change where stricter emission legislations and ever increasing fuel costs have intensified the search for effective alternatives to the conventional internal combustion engine, which has resulted in a substantial trend towards electrification of powertrains. Storage of electrical energy is the fundamental component in this technology where the lithium-ion batteries are currently considered as the most appropriate solution. Lithium-ion batteries, however, as other types of batteries, can only be used efficiently and durably within a specific temperature range.This Master thesis has been carried out in collaboration with Electroengine in Sweden AB, situated in Uppsala, which has an ongoing project regarding development of a modular battery system for electric powertrains. The project is at a stage where an initial prototype has been developed which provides the foundation for this thesis. The study has addressed the battery system performance from a thermal perspective, in order to validate the ability of the system to create a thermally serviceable environment for the lithium-ion battery cells.

This diploma work covers an investigation over the heat - and hot water systems of thetenant-owner's association, Bogården. The heat - and hot water needs of Bogården aresatisfied by both district heating as well as three heat pumps. Implemented investigationshows that the heat pumps are not used in a profitable way. Apart from that, the reservepossibilities are small. There is also a risk of the growth of Legionella bacterium in thehot water system.Since the heat pumps are already installed, HSB-Gävleborg (responsible for Bogården)has a wish to investigate possible proposed actions for optimization of existing plant.After completed investigation, a new proposed action is presented.

When harvesteing ley there is always mechanical losses from the harvest machines. During the last years the roundbalers with knives,cutting the material-are more common, This use increase the mechanical losses of material. MATERIALS AND METHODS The roundbaler which used in this test was a Krone Vario Pack 1500 Multi Cut. This roundbaler has 17 knives. The theoretical length of cut was 64 mm. During the test we stretched a rubber tarp under the balechamber and collected the materials which fell down from the balechamber.

Thermal fatigue is a serious problem in todays power plants. A large amount of damages around the world circles around that subject. The damage can come from the mechanism of two flows mixing with different temperatures in a T-junction. It is a fundamental prerequisite that these T-junctions are frequently tested for damages. An amount of criterias steers the rate of testings.

Energy losses are an essential part of a power grid company?s costs. From anenvironmental and economic perspective, it is important to reduce these costs. Toknow where efforts should be deployed, it is important to have good knowledge ofwhere in the network losses are situated. When creating network tariffs, there is alsonecessary to have a correct distribution such that the network customers that use acertain part of the network, only pays for the network losses in this area.

The purpose of the study was to investigate the use and losses of energy in an existing older building. Another purpose was also to look through various options for heating systems with renewable energy in the building. The aim was to reduce the use and losses of energy. The first step was to study the related electricity bills of the building and also perform measurements and calculations of the building envelope and ventilation. The next step was to find out the possible actions for energy saving by performing measurements and calculations.

The purpose of this report is to document the experiments carried out, methods used and results gained during research into how the silicon content of an aluminium alloy affects the coefficient of thermal expansion (CTE).The goal of this paper is to better understand and to find a relation between silicon content and the coefficient of thermal expansion.Experiments were carried out using carefully prepared samples of Al Si alloys (0, 7, 10 and 20% Si content). Using these alloys, the CTE could be measured using a dilatometer.Comparative analysis carried out could map the effects of silicon content on the coefficient of thermal expansion and an equation was created. Using simple graphs and the rule of mixture method, the authors were able to build a simple tool for calculating the CTE of specific aluminum silicon alloys..