A new build in the Swedish nuclear power system would entail increased re-quirements for the proposed repository, which is adapted after the reactors of today. With a fast reactor, capable of burning nuclear waste, operating in parallel with the light water reactors, the increased requirements on the repository could be reduced.In this thesis, simulations of a light water reactor and a fast reactor have been performed by using the Monte Carlo code Serpent to investigate the changes in the fuel inventory. The light water reactor in the study is a boiling water reactor and the fast reactor of the type sodium-cooled fast reactor and they have been used for three different operation scenarios.By studying the fuel composition and the results from the simulations of the three scenarios conclusions can be drawn. Conclusions regarding the change of the fuel inventory and decay heat in Clab as well as the interim storage facility and in the repository. Depending on the operation alternative the changes dif-fered significantly and especially regarding the mass of burned actinides for different fuels in the fast reactor.The lowest increase of fuel assemblies was meet when using 50 years old fuel with 20MWd/kg U burnout and 2,0 % enrichment for start up of the fast reactor and 30 years old fuel assemblies with 50MWd/kg U burnout and 4,7 % enrichment for the further operation of the reactor.The increase of the number of fuel assemblies was 3174, which is equivalent to 641tons of heavy metal.

In Sweden, the eutrophication of lakes, water courses and the coastal areas is considered the major threat to aquatic ecosystems and therefore actions taken to reduce the nutrient load to aquatic system including the Baltic Sea has high priority. There are many different sources of phosphorous and nitrogen and domestic wastewater is one contributing factor to the high load. Especially waste water from households that is not connected to municipal sewage treatment or a local small scale plant with appropriate nutrient removal efficiency is considered a problem. These types of households are quite common in rural areas in Sweden and in areas where summer houses has been converted to permanent living. Swedish legislation now permit the municipalities to decide in which areas within the municipality higher demands of the local small scale treatment facility should be met by the households (i.e.

Deposited waste material degrades within a short period in anaerobic environments. The methane gas that is formed provides a harmful contribute to the greenhouse effect, 23 times larger impact than carbon dioxide. It is therefore desirable to minimize the emissions of methane gas from landfills. This may be achieved by drain the landfill of gas. In this thesis the amount of produced methane gas at the landfill at Örebro has been calculated. Estimations have also been made of the amount of methane gas that might be produced in the landfill in the future.

In 2013 a new emission standard for heavy trucks was introduced and hence a number of new parts was brought in to Scania CV AB. This created a need for modifications in the silencers flow. The flow is highly complex involving several suppliers, call off methods and different models of silencers. The aim for this project was to improve the existing silencers flow. The flow, from supplier to assembling, has therefore been mapped.

Travelling children is the topic of my work. Children who commute between more than one home. Society is rapidly changing and so is the concept â familyâ . The nuclear family is no longer the most common one. Children are now travelling more frequently than ever.

Rapporten behandlar framtagandet av en produktutvecklingsmetod för industriellt restmaterial. Studien har gjorts på uppdrag av Creatables som är ett projekt inom företaget KAAV AB.Creatables arbetar med att ta fram konsumentprodukter genom att ta tillvara och förädla restmaterial från industrin, därav deras slogan Made from Waste.Dagens konsumtionssamhälle förbrukar mycket av jordens resurser och det krävs en effektivisering i utnyttjandet av dessa för att säkra tillgångar för framtida generationer. Creatables är ett ungt projekt med små resurser och således har syftet med examensarbetet varit att ta fram en ny produktutvecklingsmetod för Creatables anpassad till deras arbetssätt och storlek.För att utreda uppgiften har arbetet delats in i två delar som sedan utvecklats parallellt med varandra. En produktutvecklingsmetod och ett flertal produkter av restmaterial har arbetets fram.Litteraturstudier, intervjuer och studiebesök har genomförts för att bygga en grund för resultatet att stå på. Tidigare publicerade teorier om produktutveckling har studerats och informationen och resultaten från dessa har i kombination med produktutvecklingsarbetet använts för att ta fram en produktutvecklingsmetod som passar Creatables.Resultatet är indelat i tre huvudområden.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area.

Svensk Växtkraft is the owner of the biogas plant in Västerås. The company is planning to increase their treatment capacity at their biogas plant. In connection to this work it is also possible to make some energy saving changes to the biogas plant. The objective of this study was therefore to make an electricity and heat survey of the biogas plant, a detailed study of the heat consumption in the sanitation step and also a comparison of energy consumption with the present sanitation method and an alternative strategy where the waste is treated in 55 °C during 10 hours (the current method is heating to 70 °C during 1 hour). The energy survey was conducted in close collaboration with staff at the biogas plant. The current during normal operation was measured, power was calculated and multiplied by the time of usage to obtain the energy consumed.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area. The results show that use of locally installed renewable energy sources can reduce the total climate impact when life cycle perspective is applied.

The purpose of the project has been to work out recommendations that reduce the energy-related costs and environmental impact of HPW Fresh & Dry Ltd., a fruit drying factory in Ghana. The factory produces electricity with diesel and biogas but also purchases electricity from the national electricity company. Heat for the drying process is produced from biogas, kerosene and solar panels. In the project the energy system was analyzed by measuring production and consumption of heat and electricity. The project results show that the factory can become self-sufficient on heat if the available energy is used more efficient. The production units for both electricity and heat have low efficiencies.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area.

This bachelor thesis contains the findings of an investigation into the laying of wedge sawn wood flooring. The advantage of wedge sawn wood flooring is the usage of more material from each board reducing waste. The boards follow the natural profile of the tree where the root part of the board is wider, and the top part is narrower. The technique involves placing boards side by side with adjacent boards in opposite directions. The thick base of one board is neighbored by the narrow top of another, this creates a pattern of wedges in alternating directions, known as a ?root and top? system. Existing literature into this type of flooring is sparce.

When harvesting ley you hope to get a fast drying and a faster harvest. If there is a system with round bales, you need to have a dry matter close to 45 %. To make this as fast as possible, there is made a machine which pick up the grass with an pick-up. It turn the grass over and put it behind the machine (figure 2 and 4). There are few tests to prove the efficiency of this machine.

SyfteVårt syfte är att ge en djupare förståelse för det matsvinn som uppstår i livsmedelsbutiker genom att analysera och utreda servicelandskapets, personalens och kundens påverkan på matsvinn. Med koppling till detta syfte har vi valt följande forskningsfråga:På vilka sätt kan livsmedelsbutiker arbeta för att minimera sitt matsvinn med hänsyn till butikernas lönsamhet och kundnöjdhet? MetodDenna uppsats är en kvalitativ studie som haft sin början i ett empiriskt problem som vi ville skapa en djupare förståelse kring, vilket innebär att vår uppsats haft sin början i induktionen. Under processens gång har vi arbetat parallellt med empiri och teori, därför har studien haft ett växelspel mellan induktion och deduktion. Insamlingen av material har skett genom primära och sekundära källor där det empiriska materialet skett genom semistrukturerade intervjuer.SlutsatserI vår arbetsprocess har vi kunnat urskilja att servicelandskapet, personalen och kunden är de faktorer som påverkar matsvinnet inom dagligvaruhandeln.

Although women express a desire to be managers and although they constitute the majority of Sweden's newly graduated academics, they are still heavily underrepresented on senior management level in the Swedish private sector, where men hold as much as 95 % of the top positions. Considering the massive waste of resources that this implies, this thesis sets out to investigate the underlying reasons for the skewed gender distribution on senior management level in two Swedish professional services companies - an industry where the described problem has been palpable. Additionally, the thesis explores the effects of actively working for increased gender equality. With a basis in gender and organization theory, a broad theoretical framework has been compiled and applied to a qualitative case study design. The thesis reveals seven distinct impediments, which together create a parable of an obstacles course, that prevent women from advancing the corporate ladder in the same manner as their male colleagues.