The mining company LKAB extracts iron ore in three areas in the north of Sweden, Kiruna, Malmberget and Svappavaara. The iron ore is refined and in the pelletizing plants the material is rolled to finished pellet product. The different steps of pelletizing plants causes among other things emissions to the air. It occurs occasionally stops in the production and the emissions are vented via an emergency chimney without purification. The aim for this work is to look into how LKAB may improve their monitoring of air emissions and control of ambient air quality and the analysis methods which are suitable for measuring.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

Earlier models that measured de facto harmonization of international accounting mainly used indices and other related statistical models. Those approaches do not account for the relative importance of individual balance sheet items or expense items being harmonized. This paper therefore proposes a different approach using Runsten?s (1998) permanent measurement bias model. That way it is possible to quantify the harmonization process by accounting for differences among companies.

This project has revolved around finding better ways of overseeing vibrations of the gearbox at a wind power station. The gearbox has been a huge problem at the stations located at Gässlingen and the sooner the warning of an incoming breakdown is at hand the more money you can save from preparations. The work has been carried out together with Askalon AB in cooperation with consults from ÅF. Askalon is a company with a department focused on overseeing vibrations and it is in collaboration with that department the work has been carried out. During this work, new positions for the sensors and new methods of gathering and analyzing data have been worked out. This was then implemented at a wind power station to be tried out on site.

The master thesis, conducted at Metrima AB, concerns the development of a non-intrusivedistribution meter as a basis for individual tap water billing in apartments.The project is conducted in response to the market interest in individual tap water billing inapartments as an answer to environmental concerns regarding water consumption. Due to thehigh installation cost of traditional water meters, a new method of determining waterconsumption, without having to cut water pipes, is proposed.The proposed method distributes the total water consumption for an apartment complex toindividual apartments according to distribution meters, measuring water run-time, in eachapartment. The water run-time is estimated by measuring the water pipe?s outward vibrationsand temperature changes.A test environment was established and a prototype built, using a tilt- and vibration sensor forvibration sensing and a precision temperature sensor to measure temperature changes. As bothsensors work well in the test environment, further testing was done in 3 apartments for aduration of 5 days.

Lower energy use in buildings is a result of increasingly stringent energy requirements across Europe. When conventional district heating technology is used in areas with low energy consumption heatlosses do not fall even though the amount of energy delivered is reduced. This reduces income for thedistrict heating company. To maintain their economic viability the district heating companies? majorchallenge is to implement new solutions that minimize heat loss.

Due to human influences on the climate an increase in Earth's mean temperature is today an accepted conception. With a rising temperature discussions have started how the climate in an area will change in the future. Equally interesting and important is it also to study the precipitation in an area. Precipitation is the factor, next to temperature, that affects most how a climate in an area looks like and feels. Since precipitation is connected to evaporation the latter parameter is also of interest to study.

Increased understanding of the mechanisms that operate in conjunction with the welding of metal surfaces may help to improve existing manufacturing processes, and to enable new products and combinations of materials. The purpose of the project has therefore been to acquire a deeper understanding of what is happening in the bond for steel and for the factors that form the basis for a bond to develop between metals in the production of laminates by pressing. The merge has been done by pressing and the surfaces after the experiments have been studied in detail in the scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and with interferenceprofilometry in Wyko, to provide a greater understanding of the mechanisms that influence the bonding in the interface between metals. The project was limited to contain the materials Docol 1000, HyTens 1200, Aluminum AA3003 and a commercial steel. The parameters varied in the experiments to study their influence closer are temperature, pressure, heat treatment and pretreatment. This has been implemented by pressing with varying temperature and pressure.

An important process for grid companies in order to reduce power losses in electricity distribution grids is to figure out where and how they appear. This report describes the factors that cause power losses in low voltage distribution grids and methods for how they could be measured and analyzed. Measurement data for consumed and injected energy were collected for twelve low voltage distribution grids owned by Gävle Energi AB in order to analyze the size of the power losses and how the measurement uncertainty affects the collected data. Then models of three of the grids were created in MATLAB in order to analyze the data and the power losses were calculated to be compared to the collected data. Curve fitting were also used as a method in order to analyze the power losses from collected data.The results show that the losses in the studied grids are low.

The objective of this study was to study the agreement between two methods of indirect bloodpressure measurement in dogs and cats and to establish the within-method variation for the methods. The utility and practicality in the clinical setting were also evaluated for the both methods. The techniques evaluated were the oscillometric method and the Doppler ultrasonographic method. Thirtytwo dogs and 26 cats were used in the study and seven dogs and five cats out of these animals had diseases that may effect the bloodpressure. Bloodpressure was measured in both anesthetized and in conscious animals.

Rapid Granulator is one of the world's largest producers of granulators, which is a kind of grinderwho grinds discarded plastics to granules which later can be reused when pressure molding plastics.The company wanted help in developing a new, or alternatively extending their previous,measurement equipment. The old equipment was hard to use, required changes in the code fordifferent measurement scenarios and had a limited array of measuring quantities. Rapid had an ideaof a similar concept only with a greater number of input ports, better range of applicable sensors andan advanced yet easy to use interface. The system is supposed to be placed at Rapid's test departmentwhere it will be used as a tool for finding faults and provide data which can be used for furtherdevelopment of the granulators.The project's members accepted the task and immediately began searching for suitable componentsfor the system. After the search was completed a list of costs, limitations, sensors, I/O's anddevelopment environment was presented to Rapid's staff.

The Earths climate is changing at a higher rate, i.e between 1861 and 1994 the annual mean temperature in Scandinavia increased with 0,68º C and according to recent climate models the annual mean temperature is likely to rise with another 3º C during this century.A warmer climate in many ways is associated with changing conditions for lake ecosystems. An expected higher water temperature and a stronger summer stratification of the water column increases the risk of anoxic conditions at the lake bottom. Thus anoxic conditions are likely to cause a phosphate leakage from the sediment, i.e. a higher internal loading of phosphate.In this project, the extremely warm summer of 2002 has been used as an example for a possible scenario for a future climate. By comparing levels of phosphorus in the summer of 2002 with a ten-year median value, a phosphorus related sensitivity to climate change has been analyzed for 55 Swedish lakes.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

AbstractWith increasing population and increasing demands for comfort and thus an increase in energy demand, it is necessary to examine various energy-efficiency measures. This work deals with the ability to control the flow through the heating system to achieve the desired comfort with as little energy as possibleA heating system contains of different parts, roughly speaking, you can divide it to three main components: Heat source, Distribution and Heat emitters. All components are working together to bring heat to the building. What is examined in this report are different ways of adjusting the flow and supply temperature and how it affects comfort and energy use in a building.At today ?s date the conventional method is to use a high flow through the heating system, which affects pressure drop and cooling of the fluid.

This thesis is a part of the project "Sustainable harvesting and storage of sugar beets, more sugar to practice". The work has included a large part of practical experimental work with weight measurement, graduation and storage planning. The aim of the project is to be able to see whether the cultivars react differently in different storage conditions. The project has included storage under controlled conditions to give as accurate results as possible. To be able to mimic the farmers own preconditions the samples was harvested with a conventional Holmer.This project has two parts, one concerning the nature, time and temperature on storage where a number of different cultivars where investigated during three different recording times, two different temperatures and controlled in a controlled environment.