The division of Engineering Materials at Linköping University, department of Management and Engineering, conducted a research project concerning Fatigue life of thermal barrier coatings during 2009. During this project equipment to provoke these fatigue failure by rapidly heating and cooling test subjects in cycles, was ordered.Design and manufacturing of the equipment was handled internally at LIU.The equipment was built using a furnace that is lowered and raised over the table where the test subject is placed. To keep the temperature of the furnace a lid slides in place to close the downward facing opening of the furnace when it is in the raised position. On this door there is nozzle that is used to cooling of the test subject by air.To make sure that the equipment can work independently you need an automation controller that can evaluate if movement can occur without danger of collisions. The control system also needs to monitor that all elements are performed according to plan.This degree project is based on a modular system from OPTO 22 and includes the configuration of a PLC that will be supplied with logic and a user interface.The degree project resulted in a graphic interface in which a user can set desired values for different parameters and get information about current values for them.

The purpose of this study is, based on theories of gender and hegemonic masculinity, to studyhow masculinity and femininity is constructed and reproduced in one of the most popularSwedish podcast: Filip & Fredriks podcast. The main theory in this study is that gender issocially created and sustained by humans through language and interaction with others.The study's research questions is: How are gender roles/gender portrayed in Filip & Fredrik'spodcast? What characteristics are attributed to men and women in Filip & Fredrik's podcast?How does Filip & Fredrik's podcast represents conditions and power relations between menand women?Through an linguistic textual analysis, which is an application of discourse analysis, I seek toget beneath the surface meanings of texts and examine more implicit social meanings andideologies regarding gender. It includes an analysis of metaphors, word choices and syntax.The analysis shows underlying values and ideologies that indicates gender structures in abroader societal context. Choice of words and metaphores in Filip & Fredriks's podcastexpresses symbolism where men and male-typical attributes are highly valued, whilst womanand female-typical attributes is being devalued and representative of the opposite.Masculinities and femininities are also constructed and represented in various ways throughsentence constructions that guides the listeners in certain directions.

AbstractIn November 2011 the Swedish Government announced that they were conducting an investigation to examine what impact the conversion of existing rental stock to condominiums could have on the development of the Million programme areas. The proposal of converting rental stocks to condominiums aims to help people living in these neighbourhoods to private ownership, while still allowing people who want to continue to rent their homes to do that. This thesis intends to investigate the effects of the proposed reform from a management perspective. The maintenance of the areas built during the Million Programme gets more neglected every year that passes. The majority of the housing stock is rental properties and extensive renovation of the surface layer, tribes and public spaces are essential in all Million programme areas studied. By transforming a portion of the housing stock into condominiums and by improve the living environment through renovations, these areas would be able to gets more attractive.

MYDATA automation AB is one of the leading companies in development of surface-mountingtechnology and stencil free solder paste applications. MYDATA?s MY500 is a jet printerdesigned for solder paste application on printed circuit boards. The jet printer contains a cassettewhich consists of a holder and a cartridge. There is also a calibration unit which monitors andcalibrates the application of solder paste.

ABSTRACTThe principal aim of the study was to compare the feeding behaviour of cattle, sheep and goats on pasture and explain any differences between speices. Furthermore, I compared foraging behaviour between dry season and the beginning of the rainy season, in order to see any relationships between weather and behaviour.The study was carried out in Shompole in southern Kenya. Behavioural data were collected by observing herds of cattle, sheep and goats on pasture. The livestock were herded on pasture during the days and kept in bomas, where people live, during the nights. The weather in Shompole is characterized by high ambient temperature and low, bimodal rainfall.

This master thesis project at KTH is performed in the Mechanical and Aerospace Engineeringdepartment at University of Florida (UF). The thesis is a small part of a gas turbine researchproject where a vapour absorption refrigeration system (VARS) and a high pressure regenerativeturbine engine (HPRTE) are integrated together. The main objective is to build a computermodel of the VARS. The computer model is supposed to be used to analyse the off-designperformance of the VARS and should also be easy to integrate as a subroutine in a more complexsystem model. To model the VARS some knowledge of the absorbent/refrigerant mixture had tobe well known, in this case a mixture of ammonia and water.

The low bearing capacity of roads during the spring thaw and periods in the autumn leads every year to increases costs for Holmen Skog. To reduce costs and increase accessibility Holmen Skog decided to install and test a CTI-system. Central tire inflation (CTI) is a system that makes it possible to monitor and vary a vehicle?s tire inflation pressures from the cabin, while the vehicle is in motion. When tire pressures are reduced, the area of the contact surface between the tire and the road increases, thus reducing the ground pressure. The purpose of this study was to evaluate the CTI-equipped vehicle and analyze if the CTI technology is economical defensible during the thaw 2005.

Mechanical relays are more and more being replaced with semiconductortechnology. In this thesis it is investigated if and how the larger loads couldbe controlled by transistors. The main part of this work aims to create andverify a solution that can control the starter motor, as well as protect it incase of any failure. The different malfunctions that the solution protectsagainst is high current, too high peak current, low current, maximum cranktime and minimum cool off time. The timers also protect indirectly againstoverheating of the starter engine.The transistors used are BTS555, from Infineon.

Emerging infectious diseases poses a great future threat, not only to humans but also to domestic animals and wildlife. Even though the majority of these infections only cause minor health problems, the relatively recent emergence of HIV clearly illustrates that the next major human pandemic may surface at any time. Regardless of what the name indicates, most emerging human pathogens are not believed to be recently evolved, but to have existed previously in the natural environment. Most emerging pathogens are zoonotic, i.e. able to infect animals besides humans.

Dead wood is important for many species. The amount of coarse dead wood (diameter >10 cm) is much lower in managed forest than in unmanaged forests. Stumps constitute the largest proportion of the volume of coarse dead wood in managed forests. Since stump harvest for biofuel may increase, the amount of dead wood will decrease even more, which may threaten biodiversity. The first aim of this study was to compare the amounts of fine woody debris (FWD, .

Laser for material processing possesses a number of advantages which mean that it has been and will be an important component for a wide range of industries' future development. Cutting materials processing is the dominant use of laser technology and has revolutionized the manufacturing industry. The aim of this thesis is to describe the principles of metal cutting by laser, how laser cutting is applied in practice and to identify how Swedish companies are using laser cutting. For the theoretical and technical description of laser cutting literature studies are the primary source of information. The empirical basis for the mapping of the Swedish industry for laser cutting is grounded on a survey; this includes Swedish companies that use laser cutting in their production.

The aim of the study is twofold, to generate a sensory profile of Swedish wine today and to investigate the opinion of both wine producers and wine experts on viticulture in Sweden and wine from grapes grown in Sweden, achieved through a contextual analysis comprising a literature study and interviews with wine producers in Sweden and Denmark and wine experts from Sweden and Germany, and a sensory analysis at the company Ipsos. ?Mixed methods? was the chosen research strategy as the semi-structured interviews gave qualitative results and the sensory analysis would give quantitative results displayed as spider charts. There is a lack of studies investigating how the Swedish wine is perceived by consumers and consumers might be unaware that the Swedish wine, established through ?trial and error?, is increasing in quality every season, creating a need to display the sensory profile of Swedish wine to strengthening the perception of Swedish white wine. This study shows that the Swedish white wine today is a wine with a fresh, citrusy and flowery aroma and a fresh, citrusy and green apple taste, however, a sensory analysis cannot show if the attributes are those that are desired by the customer, a consumer test is necessary to conclude that. Trends point towards locally produced products, one reason why Swedish wine has great potential, yet the future needs to be secured through job opportunities and education. Creating an approval system for Swedish wine is suggested as a future improvement, it is a common procedure in most wine regions.

Cultural heritages are environments created by humans that are considered to have a conservation value for the posterity. They can be seen as one of society's non renewable resources. It is important to have knowledge of how cultural heritages are affected by future climate changes.The water flow in Uppsala is estimated to increase during winter and decrease during spring and summer. Precipitation will gradually increase as well as the intense short period precipitation. The average temperature is estimated to increase as well.

In the production of pulp, paper and cardboard, a large amount of water is used daily. The water has to be purified in the internal purifying plant before it reaches the receiving body of water. In the biological purifying stage at the Stora Enso Skoghall mill, an aerated basin is used where the microorganisms, using oxygen, oxidize the organic material to carbon dioxide. The air is pumped from the bottom of the basin and the oxygen can then be transported from the air bubbles to the water through diffusion. The problem with aeration of waste water from the forest industry is that wood residues, such as fatty acids, are making the transport of oxygen in water more difficult.

The project, Glowtest Fixture, has been carried out to and in collaboration with MSA SordinLtd. MSA Sordin Ltd produces and sells ear protector and is at present a supplier on theworld market. Glowtest Fixture is a product for glow testing off detailed components in oneear protector. MSA Sordin Ltd sends today away your products for testing what is anexpensive aspect in their development. The project's aim is to take forward a test equipmentthat copes with those high nonplussed requirements and wishes that are required for anapproved physical execution.Glowtest Fixture is a physical equipment that comes used stem glow physical off all detailedcomponents in one ear protector.