Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

A system for sampling of alcohol and aldehyde from diluted exhaust gases from vehicles powered by ethanol has been developed and tested. The major part of the work has been research of earlier work in the field and the construction of the sampling system.The part of the system constructed for the measurement of alcohol has been shown to work, however, more test should be performed. The part of the system constructed for the measurement of aldehyde was tested parallel to a commercially available system, based on the same principle of measurement, and has been shown to work well.Determination of the concentration of gaseous ethanol using a FID has shown the since earlier known fact that a FID is not able to measure a correct concentration of ethanol. Furthermore it has been shown that high concentrations of gaseous ethanol can not be kept in a bag more than a few minutes without a substantial decrease of the measured concentration..

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

The aim is to describe the factors that influence nurses' assessment and measurement of pain in patients. Literature study based on 13 reviewed articles, searched in the Cinahl. Qualitative and quantitative articles were analyzed. Six themes were identified that can be seen as the factors that influence nurses' assessment and measurement. The themes were   pain education, nurses´ experience in the profession, nurses´ level of knowledge about pain relief, documentation about pain, nurse´s perspective on the patient, and pain measurement.

This thesis describes a method of measuring axial magnetic leakage flux in an operational hydropower generator. Axial magnetic leakage flux is the magnetic flux at the ends of a rotating generator, which goes through the stator parallel to the rotor axis. This flux can cause circulating currents in the stator iron, giving rise to losses, and can in the worst case overheat a generator, causing it to melt down. To measure the axial flux, and how it affects the generator temperature, a measurement system was constructed on behalf of Vattenfall. The system consists of search coil sensors and a signal-processing unit with amplifiers and active filtering.  To confirm the behaviour of the axial leakage flux and the functionality of the measurement system, a test installation was made.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

This report discusses the development of an autonomous system that can travel a distance of atleast 30 meters on two wheels. The system, the robot, detects black lines and stops if one isdetected. A remote control can be used to start and stop the robot. The robot is constructed ofmainly steel with smaller, more detailed, parts in plastic. A significant amout of time has beenused to enable the robot to balance on its own.

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution.

För att uppfylla kraven på kvalitetssäkring samt evidensbaserad praktik måste hörapparatanpassning utvärderas objektivt. Syftet med studien är att redovisa nya forskningsresultat gällande objektiv utvärdering av hörapparater med hjälp av hörselgångsmätning, samt att beskriva en modern, evidensbaserad och kliniskt användbar metod för de vanligaste typerna av elektro-akustiska hörapparater med olika typer av insats. Studien består av en allmän litteraturstudie som beskriver tidigare rekommendationer samt en systematisk litteraturstudie där nya rön gällande metodiken vid hörselgångsmätning presenteras. Utifrån hörselgångsmätningens olika delmoment undersöker studien vilka konsekvenser de nya rönen har för utförandet vid hörselgångsmätning. I slutsatsen presenteras en metod för objektiv utvärdering av moderna hörapparater..

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution. The work proceeded with an extensive search for abrasive flow meters along with obtaining information about flow measurement in general. When the search for abrasive flow meters resulted in nothing all the efforts were concentrated on finding a principle of measurement that could cope with the criteria.

The boiling properties are an important quality issue of the potato. In order to obtain adequate boiling properties the growth of the potato needs to be controlled and interrupted at the right time. However, it is difficult to determine when to stop the growth. Specific gravity can easily be measured and can sometimes be used as a tool for estimating the boiling properties. This report discusses different aspects of the specific gravity of the potato and how it can be used as a tool to determine the appropriate time for vine killing.

The boiling properties are an important quality issue of the potato. In order to obtain adequate boiling properties the growth of the potato needs to be controlled and interrupted at the right time. However, it is difficult to determine when to stop the growth. Specific gravity can easily be measured and can sometimes be used as a tool for estimating the boiling properties. This report discusses different aspects of the specific gravity of the potato and how it can be used as a tool to determine the appropriate time for vine killing.

This study is a part of a larger project where the aim has been to evaluate different methods to assure the quality in stallion semen, due to the fact that some stallions in horse breeding have poor semen quality. The increased use of transport semen requires new methods to ensure good semen quality. In this part of the project the viability and concentration in fresh and cooled semen was examined with NucleoCounter SP-100. A comparison between two different commercially available semen extenders, Kenney?s and INRA 96, was made.

Over 40 miljon people in the world suffer from hiv/aids today. Africa is the continent that is worst affected by hiv/aids but how is the situation in Sweden? Why is it so quiet concerning hiv/aids in Sweden? Our aim with this work was to find out about the hiv/aids situation in Sweden and particulary in Malmö. The result of our research was that hiv/aids have increased since the year 2000 and most of the people had caught the infection in other countries than Sweden. This raised our curiosity concerning how immigrants/refugees are being treated when they arrive in Malmö and what are being done to stop hiv/aids from spreading further.We became very disappointed when we realised how little that is actually being done and how poorly the collaboration between the institutions are working.