Over the next few years, major investments in healthcare buildings is to be performed. Most surgical theaters are in need of technological upgrades as the technology is outdated. In most cases not only a refurbishment is performed but also an expansion. The basis for expansion, is due to a large increased number of patients, but also to the complexity of the refitment. Partly it's because evacuations are difficult to implement and the disturbance that occurs in conjunction with the refitment.Löwenströmska hospital undergoing a technical upgrad.

An important task for Region Skåne is to allocate resources to the health care districts. From 1999 to 2002 Region Skåne used needs-based resource allocation as a model for allocating resources. In a needs-based resource allocation individuals with the same socioeconomic and demographic characteristics are assumed to have the same level of need and are therefore allocated the same amount of resources. During the period of needs-based resource allocation a matrix model was used as a method. In the matrix model individuals were divided into cells after each combination of the socioeconomic and demographic variables.

This is a thesis presents a differential gear which is found in a tracked vehicle called BvS10. The tracked vehicle is manufactured by BAE Systems Hägglunds AB in Örnsköldsvik, Sweden. The differential gear has a bolted house. The differential meets the requirement Specifications, but the problem is that the bolts are sheared off because of the extreme torque that the differential is exposed to resist.Previous report on the differential show pictures of bolts which have been sheared off at the threads. This report is also includes three lists that explain seven different proposals which some are approved and some are not, and the report also presents the force, tensile, and shear stress.In a bolted connection there is both axial tension stress and radial shear stress, which can lead to wear out and broken bolts.

Unmanned aerial vehicles (UAV?s) are nowadays greatly appreciated. The advantage over manned airplanes are great since UAV?s can be much smaller and therefore lighter. The goal of this project is to evaluate the performance of an environmentally friendly UAV using only lithium-ion batteries.

This thesis is performed as a summarizing project for the mechanical engineering education at School of Engineering in Jönköping. All knowledge necessary to complete this thesis was gathered from previous courses and education.This project was to develop a new product for the company TR Equipment AB in Tranås. The new product is going to be based on an already existing product, TR 1700. TR 1700 is a bathtub equipped with a height adjustable function. This product is used in retirement homes and in the care of disabled people.

Eco-design is all about improving products environmental performances throughout the products lifecycle by including the environmental aspect into the product development process. There are a large number of different tools that can be used for this, but there are several factors that can affect which one will be the best to use. Some tools for eco-design takes comprehensive studies and can only be performed by experts, while some tools can be used more time- and cost efficient and with basic knowledge. The choice of tool should be based on the company?s situation.This report describes the research of how the design and furniture company Blå Station could include a tool for eco-design in their product development process.

In order for construction projects to be completed within the specified time limit while at the same time be financially sustainable it requires thorough preparation and an extensive planning. Most essential is the groundwork and the design that determines the project's progress. There are many aspects to consider in order to avoid inconveniences such as delay, litigation, unexpected cost etcetera. If mistakes are made in an early stage it is very likely that the error will follow the process and become an expensive correction cost towards the later part of the project. In other words, it is expensive to rectify defects later on.

This report describes the results of the project "Concept development of jet engine inspection plugs" carried out in the spring of 2008. The work was done at the department of product definition at the company Volvo Aero in Trollhättan. The objective of the work was to develop concepts for a "Volvo-unique" inspection plug. The work is part of Volvo Aero's focus on proprietary (self-developed) technologies. Inspection plugs can be found on virtually all aircraft engines and gas turbines.

The issue about how Scania shall perform HVAC tests in the climatic wind tunnel CD7, which Scania is about to complete by year 2013, has resulted in four test methods for truck HVAC and also a test method structure. The test methods have been chosen to focus on sun, snow and rain simulations. These are adapted and developed according to what should be tested and to what can be tested in CD7, which has been the object. With CD7 different climates can be simulated in a controlled environment for complete truck level, from desert with high sun load to arctic cold and snow.The test methods represents a basis to start from, for designers and test engineers which make the testing more repetitive as well as time eventually can be saved. Before the test methods can be applied they must be verified as they are based on theoretical and empirical assumptions.

To be able to move around without having to think about each movement is for most people amatter of course. Todays society contributes to a life at high speed where the sparetime is oftenspend doing somekind of sport, even extreme sports which earlier only a few people wheredoing. This leads to not only good health effects but also to more injuries. One of the mostcommon injuries is the knee injury.Capio Artro Clinic is a clinic specialized in sports medicine and particulary patients with injuriesin knee, shoulder, foot, hip or elbow. They perform a great part of all the crucial ligamentsurgeries in Sweden and has therefor also a lot of patients in need for rehabilitation of the knee.During the rehabilitation the load of the injuried knee is increased in steps.

As the cities are becoming more crowded, the urban distribution has become a major logistical challenge. Some commonproblems in the inner cities arelimited accessibility and idling. Many of Sweden's municipalities are above the limit values for PM10limit set by the EU.Sundsvall is one of these municipalities and has the vision to create a sustainable city and region. Sundsvall LogistikparkAB is part of an EU project, SMARTSET, which is collaborationbetween several cities in Europe. SMARTSETSundsvall is about to develop a market-based sustainable model for city logistics.

In this report the two authors, and project contributors alike, describe their work withdeveloping a solar cooker intended for usage in the developing countries of the world.Specifically, the work aims at developing a new, solar heat driven cooking device, possiblybased upon the current product. This should, in comparison to the current product, be lighter,easier to transport and to produce. Also, the new product?s production mustn?t be more costlythan today and the included materials and components must be obtainable from within theBolivian national borders where the product is currently produced. During the project, certainadvantages with a more efficient, and, above all, a more moderately priced product, werediscovered.

Laser for material processing possesses a number of advantages which mean that it has been and will be an important component for a wide range of industries' future development. Cutting materials processing is the dominant use of laser technology and has revolutionized the manufacturing industry. The aim of this thesis is to describe the principles of metal cutting by laser, how laser cutting is applied in practice and to identify how Swedish companies are using laser cutting. For the theoretical and technical description of laser cutting literature studies are the primary source of information. The empirical basis for the mapping of the Swedish industry for laser cutting is grounded on a survey; this includes Swedish companies that use laser cutting in their production.

This degree project has been carried out by Oscar Adolfsson and Marcus Blomqvist, during the spring of 2010, both studying to become Bachelor of Science in Innovation and Design Engineering, at Karlstad University. The degree project includes 22,5 credits.The work is done on behalf of Etac Supply Center AB in Anderstorp. Etac is a company developing and manufacturing home health care products, with operation in Sweden, Norway, Denmark, England and Germany, and with sales worldwide. Bo Lindqvist, R & D manager has been the contact person at Etac.During the project the students has had a workplace at Semcon Caran AB in Karlstad. Semcon has also been helpful as a sounding board.The objective of the work has been developing a new, wall mounted shower chair, assigned for persons with difficulty to stand up while showering.Etacs requirement of the shower chair is that it should be able to support a user with a weight of 100 kg, the chair shouldn?t have any outrigger, optional should be armrests and backrest.

ÅF Test Center in Borlänge had a need to expand their capacity for compressive and tensile strength tests. They wanted to do this by using a hydraulic cylinder, which they already possessed, to apply the force with. This required a load receiving structure. The aim of this work was to design and dimensioning a test bench for a cylinder marked NIKE 300 tons. The work would result in a completed design proposal on a test bench which could manage to run the compressive and tensile strength tests of up to 3000 kN.