Currently, there are no clear statistics on how the floor plan and room size in apartment buildings has changed over time since the postwar period. The statistics available is average area per apartment which can be found on Statistics Sweden's website. This report has the aim to increase knowledge about how the Swedish home have changed over time.The questions that the report will answer are:For apartment buildings, how has the living area been distributed since the postwar period?Why has the area distribution changed over time?A survey of the houses built during 1950-2014 was made before questions could be answered. A case study was also made which a total of 90 apartments were analyzed and divided into three eras, the people´s home, the million programme and the neomodernism.

In this report an MCNP (Monte Carlo N-Particle) model is described for the reactor vessel at Ringhals 2. The model is validated against the specific activity in neutron dosimeters, extracted in 1977, 1984 and 1994. The validation showed that the calculations of the model are within the requirements of a maximum of 20 percent uncertainty for every neutron dosimeter except one, extracted after the first cycle. The uncertainty of this cycle was mostly due to the operation data rather than to the MCNP model.The model has been used to investigate various questions concerning radiation damage. The reliability of the traditional measure of radiation damage, fast neutron flux (En > 1MeV) has been evaluated.  This has been done by taking the ratio for this and another measure of radiation damage, DPA (Displacement Per Atom), for various positions and layers.

Control and comparison of various cleaning methods on restaurants in Södra RoslagenThe purpose of this report is to find out and analyze the efficiency of cleaning methods in restaurant kitchens. The investigation was carried out through unannounced inspections at 89 restaurants in Södra Roslagen (municipality of Danderyd, Täby and Vaxholm). ATP-measuring was done on a plate, a knife, a bench surface and a cutting board. The ATP-method measured the amount of food residue on equipment and working surfaces after cleaning, with a luminometer and swabs. Restaurant staffs were asked to describe in detail how and when the last cleaning was carried out on the surface.

During a fire large amounts of particles and unhealthy agents occur.  Polyaromatic hydrocarbons (PAH) and toxic metals are examples among many others. These agents have a capacity to bond to particles and when the fire is extinguished, the particles can be transferred with the extinguish water into the soil and to the groundwater.Recent studies in particles have been conducted. A study by Ulrika Iverfelt (2014) reviled that the particles from a fire contained large amounts of both PAH and metals, which is consistent with earlier analyses. Her column experiments with particles in the size ? 11 microns and ?100 microns in silica sand, reviled that the larger particles was immobilized because the transportation was influenced by sieving or physiochemical particle and surface interactions.The transport of the particles in soil and groundwater is regulated by two main mechanisms: physiochemical surface interactions and straining.

In my project I worked with fluorescent color and fear as a theme together. It was based on my question for what happens when you take all the lights out and highlight a fear or phobia. I wanted to experiment and explore the course of event within the surface of a picture by using this kind of paint.I worked with illustration and pattern to bind the two pictures together. The aim was to investigate what is possible with the picture as a medium and work with contrast to make it as effective as possible. My goal was to make one poster of each fear and to make them work together as a series as it?s best.I asked myself many questions such as;? What happens to the surface, image and room when you use this color?? Will a new quality appear?? What happens when you mix two pictures together on a parallel level that only show in different kind of light?.

The aim of this project is to find a concept solution for a wireless transmitting system, installed to transmit data from a hydrophone of the ocean floor down by a wave power generator to the office on shore. The project is a literature review in which previous observations and tests are analyzed and put together to find a solution. The result was a comprehensive solution that includes an acoustic modem to transfer captured information from the bottom to the surface, wirelessly through the water. The information is then sent fron the surface on radio waves through the GSM network to the office on land. Between under and over water there are components to convert information between acoustic waves and radio waves, but also various types of modulation, such as amplitude and frequency modulation is required..

AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

Increased understanding of the mechanisms that operate in conjunction with the welding of metal surfaces may help to improve existing manufacturing processes, and to enable new products and combinations of materials. The purpose of the project has therefore been to acquire a deeper understanding of what is happening in the bond for steel and for the factors that form the basis for a bond to develop between metals in the production of laminates by pressing. The merge has been done by pressing and the surfaces after the experiments have been studied in detail in the scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and with interferenceprofilometry in Wyko, to provide a greater understanding of the mechanisms that influence the bonding in the interface between metals. The project was limited to contain the materials Docol 1000, HyTens 1200, Aluminum AA3003 and a commercial steel. The parameters varied in the experiments to study their influence closer are temperature, pressure, heat treatment and pretreatment. This has been implemented by pressing with varying temperature and pressure.

AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

Glass has sophisticated front properties and are used as facades in high buildings. During cold periods, these glass facades could cause thermal discomfort, due to cold downdraught. Cold downdraught can be countered by placing heaters under glass surfaces. Nowadays technology offers highly insulating windows, which is why there is an interest to investigate the indoor climate with only underfloor heating. The research in this area is limited, and few empirical methods are available.

Österbyverken is an industrial estate in Östhammars municipality in Uppland, Sweden. Many different activities have taken place on the estate the last 600 years. During the last 15 years both health and environmental studies have been made by different companies. At the most recent study a great increase of metals in Nerån, a river that runs partly through and partly next to the estate, was identified with mass balances. The purpose of this thesis is to accomplish a deepened study about the reasons for the increase of metals in Nerån.

Delineation of recharge areas for aquifers is performed in the groundwater mapping process at the Swedish geological survey, SGU. This work is time consuming and performed manually. It is therefore desirable to develop a more general and repeatable method for defining recharge areas for aquifers.The purpose of this study was to investigate two other possible methods to delineate recharge areas for aquifers. The first method was to examine the possibility of using the topography of the bedrock to define the recharge areas for aquifers. To enable this, a method for generating the topography of the bedrock was developed.

Ocean Modules Sweden AB is a small business active in the field of underwater technology. Thecompany was contacted by the Swedish Defense Materiel Administration (FMV) in order todevelop a new system that would conform to their specific requirements. Two students at theRoyal Institute of Technology (KTH) were consulted in conjunction of this project in order to aidthe development and conceptual design of the system.The primary users of the system are the divers of the Explosive Ordnance Disposal division (EOD)- a branch of the Swedish Armed Forces. The purpose of the product was to incorporate allnecessary functions required by the EOD divers into one single system. The main functions arecommunication between the surface operator and diver, video recording, still imaging, positioning,navigation and ocean floor mapping with sonar.

Lake lowering in sulphide-rich areas is currently a major environmental impact for surface water. This study focuses on whether there is a relationship between a gradient of lake lowering and surface water impacts in areas of sulphide-rich sediments, in order to better understand their contribution of heavy metals and sulfuric acid. Also, is it a reasonable method to use the reduced lake area in order to quantify the gradient? The survey was conducted by collecting water samples from reference lakes and lowered lakes from south to north in coastal areas within the county of Västerbotten. Water samples were then analyzed for TOC, pH, conductivity, anions, base cations, alkalinity, acidity, sulfate, Al, Cd, Fe, Mn, Cu, Zn and Pb.

This thesis work is intended to analyze whether the municipalities has a need for the new technology of mobile mapping.Mobile mapping consists of the technologies of laser scanning, photographing and positioning of streets and roads in city environment and in the countryside. When these technologies are operating together a georeferenced three-dimensional image model is created, which has specific coordinates that states its position on the surface of the earth. Thanks to the laser scanning process even measuring can be performed in this model.The municipal sector consists of many different departments which use visual spatial information. These departments are an interesting target group for this system. Specific departments within the municipal sector, which we considered were the most suitable, have been selected.