In this thesis, two studies with different drills were included. In one of the studies two drills were compared: Väderstad Rapid and Väderstad Spirit. In the other study various drills for direct drilling were compared. The study with Rapid and Spirit was placed in two locations with different autumn tillage; one on ploughed land in Uppsala and one on cultivated land in Västerås, both with relatively high clay content. Rapid drills have a single disc coulter, while the Spirit drills have a double disc coulter. Various aspects were compared such as aggregate distribution, seed placement, emergence, crop yield and economic outcome.

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution.

The production of cheese is in continuous development with objectives to in-crease productivity, achieve changes in shelf life and functional properties of the products. One concept in the development is to substitute milk fat with vegetable fats and oils in the manufacture of cheese. The objective of this study was to investigate effects on cheese yield and cheese quality of 4 different semi-hard analogue cheese products produced by substituting milk fat with vegetable fat, each analogue cheese with a specific mixture of vegeta-ble fat. As reference a cheese produced with anhydrous milk fat was used. The yield and recovery of fat and protein were determined by recording the weights of each cheese direct after press and after 20±2 days of storage and analysis of the composition of the cheeses after 20±2 days of storage. The cheese was fur-ther subjected for texture profile analysis in a TA-XT Plus Texture Analyser and analysed with Differential Scanning Calorimetry (DSC) to examine whether the fat behaves similar in the cheese as in pure form in respect to its thermal properties. The cheese yield was not significantly different when using different fats. Differ-ent amounts of water were absorbed during the water cooling.

ABB I-R Waterjet Systems combines the robotics and motion expertise of ABB Flexible Automation with high-pressure intensifier/pumping technology from Ingersoll-Rand to provide and continue to develop innovative waterjet cutting systems for global markets. The purpose of this assignment is to develop a process water purifier. The purifier should be applicable as an option to ABB I-R?s production cell Cutting-Box. At first hand the process water should be purified well enough to let out in the municipal sewage system, but the ultimate solution is purifying the process water to the range that recycling is possible. When investigating the different principle of purifying water, a research of different products and their manufactories was done. These different products were compared and the principle of filtration was the most applicable, as most of the products were designed for far larger applications. As the process water contains quite large amount of particles, it is necessary to perform the filtration in different steps. The process water purifier is therefore composed of a module of coarse filtration and one of micro filtration. In the module of coarse filtration the mainly amount of fibres and particles are eliminated. They are kept back in the container unit with the larger fragments and dumped with these when the container is emptied. In the module of micro filtration the filtration is performed in two steps. In the first step particles larger than 50?m are eliminated, in the second step the micro filter is setting the range of purifying, in this case 10?m.

Ocean Thermal Energy Conversion (OTEC) is a technology that utilizes the temperaturedifference in oceans between the warm surface water and the cold water at 1000 m depthto produce electricity. The purpose of this report is to investigate if OTEC with its synergiescould become a commercially feasible energy solution for a small island. A literature reviewis conducted to explore the different OTEC technologies and to what extent the threesynergies; fresh water, air conditioning and aquaculture, could be used. In order to calculatethe profitability of these synergies there is also a study conducted on the conventionalmethods and cost of fresh water production, aquaculture and air conditioning. A model is setup using a scenario of a small tropical Island with population of 100 000 people.

The focus of this study was to examine the nutrients and benthic organisms of the bay ?Mönsteråsviken?, which is influenced by eutrophication. The purpose was also to look at an interesting gradient forming in the bay, namely the distance from the river outflow of Lillån. At 18 sampling sites in the bay samples of water, sediments and benthic organisms were collected in late April of 2011. The water was analyzed for nitrate, phosphate and chlorophyll.

Perfluorinated substances (PF) are environmental pollutants that are used to coat fibres of so called ?all weather clothes? to make them water resistant. PF are effectively spread through water. Waste water treatment plants (WWTPs) are a pollutant source of these substances. PF are poisonous to different kinds of organisms, and supposedly also to human beings, if concentrations are sufficiently high.Perfluorinated substances have been investigated at three waste water treatment plants in Stockholm during the 2000?s.

Today there is a large consensus about the importance of Swedish schools providingconditions enabling students to develop the ability to manage and learn through information technologies (IT). The goal of this study was to describe and examine how national education goals for the use of IT transformed into municipal IT-strategies for the school. A content analysis was conducted of thirty-eight municipal IT-strategies collected from Swedish municipal websites on the Internet. The content in the municipal IT-strategies was compared with the content in both the Swedish education act and the national curriculum. The results showed that the content in the Swedish education act and the national curriculum in fact was translated into municipal IT strategies, but that the range of strategies concerning technology, pedagogy and content in relation to IT was broad.

The research group Soil and Water Management at the department of Soil and Environment at theSwedish University of Agricultural Sciences in Uppsala are studying greenhouse gas emissions fromcultivated peat soils. To measure carbon dioxide emissions from peat soils in the field the researchgroup are now using two portable carbon dioxide meters (Vaisala GMP343). For practical reasons,they plan to acquire a new type of automated field meter. The aim of this study is to evaluate thepresent meters to see how environmental conditions and instrument settings affect the results,which is meant to facilitate the introduction of the new field meter when the meters needs to becompared. As a part of the study the relationship between groundwater level and carbon dioxideemissions from peat soils will be investigated.The evaluation of the two carbon dioxide meters was made by connecting them to one single airtightsystem, with the aim of creating identical measurement environments.

Stump treatment today requires large quantities of clean water mixed with the protective product Rotstop, to fully cover the stump surface. In order to reduce the water consumption without reducing the coverage of the stump surface, the pressure in the stump treatment device can be increased. Therefore, the Phlebiopsis gigantea (Fr.) Jül. suspension used as a biological control agent to prevent Heterobasidion annosum (Fr.) Bref. infection was pressure-tested.

The continuous process of urbanization results in demands on research and development for ecological and sustainable city development. Because of this, the current systems for wastewater treatment may have to be improved. In order to evaluate new technologies for municipal wastewater treatment, a development project has been initiated for the new district Hammarby Sjöstad in Stockholm. The project is lead by the company Stockholm Water. High environmental standards have been put up for the district, as it must be twice as good as an ordinary new district.

The main purpose of this thesis has been to find a way to evaluate the soil parameters for the Total sounding method (TS), such as the inner friction angles and settlement modules. This study only includes an analysis of soil profiles from the Stockholm region. The chosen location for the study is a proposed residential area east of Igelstaviken in Södertälje. Presently, the subject plot is located in a residential area and is also adjacent to a school area.Total sounding is originally a Norwegian soil testing method. The differences between the sounding methods (weight-, ram-, CPT-sounding) are for instance how the sound is driven into the ground and what kind of parameters that are registered.

Treatment wetlands been showed efficient for reducing pollutant in waste water. In Lajeado ? RS, Brazil the landfill has poor leachate water treatment. It is necessary to supplement the treatment plant because they need to reduce BOD, COD and nitrate of the water going to recipient. A subsurface flow wetland (SSF) can be a good choice.  In order to be able to design an efficient SSF it is important to understand how the grain sizes of a substrate affect the reducing of pollutants in waste water.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution. The work proceeded with an extensive search for abrasive flow meters along with obtaining information about flow measurement in general. When the search for abrasive flow meters resulted in nothing all the efforts were concentrated on finding a principle of measurement that could cope with the criteria.