This report is part of the major thesis carried out at Stoneridge Electronics in Bromma,Stockholm during autumn and winter 2005-2006. The background to the thesis is the trendwithin the automotive industry where color displays have become more common for presentationof information to the driver, a trend that has come to the commercial vehicle market. Thepurpose of the thesis has been to evaluate whether programmable logic, with respect to FPGAtechnology, could be suitable for display control and graphics generation of these more complexcolor displays in automotive environment.Within the scope of the thesis the FPGA technology has been investigated, i.e. whatopportunities and threats there are with aspect to environmental and security requirements. Inaddition, the market of FPGAs and pre-built IP-cores has been investigated.

At the Department of Technology and Built environment at the University of Gävle there was an interest to study GNU Radio, which is an "open source radio project. The project is based on that most of the radio signal processing is made in an ordinary PC. The idea behind this degree project was that in a laptop there are several radio transmitters/receivers that takes space, generates heat and transmit in varied frequency band etcetera. All these radio transmitters/receivers could be replaced with a Software Defined Radio system. It means that one common, general radio hardware is used to different communications such as: WLAN, Bluetooth, GPRS, 3G etcetera. The waveform is generated in the software, which makes the system very flexible.

This study examines the use of building modeling and energy simulations in the design process  of  a  building.  The  take-off  point  is  the  notion  of  energy  simulations  being needed early and throughout the building design process, and that the lack of energy simulations may be explained by the fact that they are time consuming and therefore often too expensive. A greater interoperability between software tools used by relevant disciplines,  such  as  the  architect  and  the  energy  specialist,  would  create  smoother workflows, which would reduce this cost and open up for more frequent and iterative energy  simulation  processes.  The  study  is  an  assessment  of  the  modeling  tool  Revit and  the  simulation  tool  Virtual  Environment  and  whether  they  can  create  smoother workflows, and make leeway for a more frequent use of energy simulations throughout the  design  process.  It  also  investigates  the  limitations  of  what  can  be  examined  by simulations in Virtual Environment. This will hopefully help clarify the future role of energy  simulations  in  design  processes.  The  method  is  a  trial  by  error  approach  of testing the two software tools by building and simulating a model. The results of these tests  show  that  the  workflow  is  not  optimal  (and  therefore  time  consuming)  for frequent  and  iterative simulations  throughout the  design  process,  but  it  also  reveals some  great  possibilities  of  what  can  be  performed  with  these  two  powerful  tools  at hand.  Further  development  with  regards  on  platform  independency  of  the  building information  model,  including  seamless  exporting  and  importing,  seems  necessary  to strengthen the future role of energy simulations..

Abstract The purpose of this project is to develop a modular processor card which is intended to work as a platform for Kitron Development Karlskoga. The modular processor card is meant to be used as a control system in development projects, mainly in medical and industrial products. The processor card will consist of a central unit with the basic functions for a control system. Furthermore there will be complete modules with machine commodity and programming, to pick exactly the necessary functions for a specific application. With consideration to the specification of the development and the main unit, I chose an adequate microprocessor (AT90CAN32) as core and interface circuits to stated border areas. The construction is first completed in the program MultiSim and then remade in the program OrCAD Capture. The programming language C was used in the software model.

A key part in the development and verification of digital systems is simulation. But hardware simulators are expensive, and software simulation is not fast enough for designs with a large number of gates. As today?s digital zesigns constantly grow in size (number of gates), and that trend shows no signs to end, faster simulators handling millions of gates are needed. We investigate how to create a software gate-level simulator able to simulate a high number of gates fast.

The competitive nature of the automotive industry has always implied a necessity to improve product development concerning time-to-market, cost and product quality. As capacity of computer-aided engineering (CAE) tools has evolved, so has the strive for simulation-driven design. Virtual durability testing using full vehicle models is one of many challenges posed in front of vehicle manufacturers when computer simulations are given a key role in product development.This thesis has been initiated as a preliminary step towards implementing dynamic virtual durability testing in the development of buses and coaches at Scania. The objective has been to assess the predictability of a full vehicle coach model and to what level of precision structural loads can be predicted. Previously performed proving ground testing of a Scania Touring coach has been the basis for the modelling and simulations in this thesis.A virtual model of the Scania Touring coach has been created in multi-body simulation software package MSC.Adams.

The majority of free content on the internet is financed by online advertising. A requirement for thismodel to work is that the visitors see the ads. The emergence of ad-blocking software has shifted thepower from the advertiser?s choice of publishing ads to the consumer?s choice of viewing ads. Weexamine the consumers? opinions regarding the use of ad-blocking software and compare them to theopinions of companies using online advertisement.

Opcon Powerbox is a product developed by Opcon together with the underlying company SRM (Svenska Rotor Maskiner) where surplus heat from the industry is used through an Organic Rankine Cycle (ORC)?process to produce electricity. An ORC-process is a thermodynamic circle process in which a refrigerant is used as the working fluid. The refrigerant makes it possible for the circle process to operate at lower temperatures than the conventional Rankine process.In this master?s thesis a data analysis software for the Opcon Powerbox has been developed in which measurement data is retrieved and handled from the Opcon Powerbox.

With recent technical development computer aided design and manufacturing has taken amore important role in the product life cycle. New business segments such as Product/ServiceSystems and remanufacturing is emerging. This development demands better control of theproduct data throughout the entire product life cycle. Computer aided design is widelyrecognized and used within the manufacturing industries and in recent years the importance ofDigital manufacturing has increased. One part of Digital manufacturing is paperlessproduction which involves all orders and working instruction shown for example on a screenrather than on a piece of paper.

The exclusion of visually impaired from the information flow presented to us through signs was what led me into this project. With a growing amount of information being presented to us on signs and digital information surface the need of communicating this information in a way that could be read by visually impaired is evident. Looking into different ways of communication, my goal was to create something that filled the need of the visually impaired without branding them as disabled. Having a close relative with bad eyesight is became evident on how much it limited her in her everyday life, not being able to navigate herself without the support of her husband. Through interviews with her and others with varying diagnoses I reached an insight in their situation. To my surprise they still favored a visual form of communication before an auditory or tactile form, because it?s easy to survey and quick to interpret.

The earmould acoustics affect the amplification that the hearing aid is programmed to give to its user. It is therefore important that the choices made for the earmould are correctly done. One choice is regarding the shape of the soundbore that affects the frequency response of the hearing aid above a certain cut-off frequency. The purpose of this project was to measure the frequency response when altering the shape of the soundbore in the earmould. Additionally, the aim was to examine how the frequency response is affected when the shape of the soundbore is not set or is not possible to set in the software when programming the hearing aid.

In most software engineering project, users are only involved in the beginning of the project as a help to design the requirements specification but users can be involved after this phase too, but is it effective to do so? With this report we would like to investigate how effective it is to involve users after the requirements specification has been written and approved. To find out how effective it is to involve the users we try some fast and simple involvement techniques on a quite far gone project. These techniques include ethnographic studies, prototypes and surveys. We also interviewed a couple of people who work with usability and finally delivered a report with our results to them to find out if they found our result relevant. By also documenting how much time we spent involving users we will show to which degree user involvement is effective. We found out that a couple of fast techniques could get very much result in the form of usability enhancing suggestions to the developers.

When the use of encryption amongst the regular computer user grows morewidespread than ever it makes the life of the IT-forensics experts difficult.Hampering the judicial investigations that otherwise could have lead to convictions.In this report we will treat the subject of crypto analysis with a focus on decrypting files and devices encrypted with the software TrueCrypt. A solution will be presented that can facilitate the future work involving encryption. The application DFEAT that has been developed during the writings of this report is faster than the corresponding software EFDD, and attacks both partitions and bitwise copies of entire harddrives where PKF fails.DFEAT is a lightweight application that is almost 50 times smaller compared to EFDD and 200 times smaller than PKF's portable version..

This thesis describes a tool for data mining used to optimize ambulance preparedness. The goal with the tool was that it should be able to retract the information necessary to be able to analyze and calibrate the preparedness model used in the software ResQMap. ResQMap is used by SOS Alarm, who are responsible for the Swedish emergency number 112, as a decision support tool for ambulance operators. It is developed by Carmenta AB, who are the supervisors of the thesis work. Also, a minor study of the preparedness models variables has been performed in order to be able to evaluate the function of the tool.

This bachelor thesis portray a project where the main task were to develop a computer based system prototype for handling of absence report at the upper secondary school af Chapman in Karlskrona. The project has been conducted in cooperation with students from the university programs software engineering and information economy at Blekinge Institute of Technology. Our task as MDA-students have been to survey the process of absence report of today through field studies and give a proposal of a graphical user interface which later were developed by the software engineers. The thesis also handles the cooperation with other students from other university programs..