An analysis of a specific application of anaerobic wastewater treatment at a pulp and board mill, Stora Enso Skoghall, was carried out. A literature study was done and effluent wastewater from CTMP pulp production was analyzed. The analysis consisted of a broad constituent analysis and an anaerobic treatment trial. Results from these test where used to calculate the treatment effectiveness and resulting energy potential at the mill.The literature study and constituent analysis showed that toxicity of the water to be treated, due to wood extractives and sulphur content, was of concern. Detoxification chemicals targeting these constituents where used in the anaerobic treatment trial.

AbstractThe purpose of this study was to identify problems that may occur in the execution of a civil engineering project and suggest measures to reduce the risk of errors. The study was conducted in cooperation with a civil engineering company in the Gothenburg area. During two weeks in February 2012, a field study took place on two construction sites where disruption and problems that took more than 15 minutes to correct were noted. During the field study we identified 39 such occurrences in the projects and then these were classified into different categories according to their cause.The two largest categories were "Design" and "Planning", which accounted for half of the errors that were discovered.In the study results were evaluated to decide whether it was possible to detect discrepancies at an earlier stage. The cost to fix an error in the design stage may be significantly less than to correct the problem in production.According to the evaluation, 55% of the errors could have been detected earlier if there was a greater degree of observation for such issues by everyone involved in the project.

The purpose of this review was to study the cow eye physiology, focusing on how it registers light, and to see how light affects the cow?s milk yield. It has been showed in studies that more hours of light per day (16 hours of light a day) as opposed to about 9-12 hours of light a day, increases milk yield for dairy cows. This review contains suggestions on how this is connected with the physiology of the eye. Vision is an important sense for many mammals, and is used to check out the animals surroundings. Sensor cells in the eyeball help in turning photons from the light into signals to the brain.

Detta examensarbete syftar till att exemplifiera vilka informationsparametrar som är nödvändiga för att Building Information Management på ett bättre sätt ska kunna implementeras i produktionsfasen. För att uppnå detta mål har vi analyserat utvecklingen och nyttjandet av Building Information Management genom tre olika datainsamlingsmetoder; litteraturstudie, observationer och intervjuer.  I detta examensarbete har vi fördjupat oss i för- och nackdelar samt hur Skanska Sverige AB kan tillämpa Building Information Management som hjälpmedel i arbetsberedningar. Denna fördjupning har lett till att vi kan analysera vilka produktionsanpassade informationsparametrar som en produktionsledare behöver i sin tjänsteroll för att dra nytta av Building Information Management.Vi anser att användandet av en BIM-modell kompletterar produktionsledarens ledaregenskaper, vilket gör det lättare för denne att nå fram med informationen till yrkesarbetarna, då visualiseringen underlättar förståelsen inför aktiviteten. I denna rapport kan läsaren ta del av de slutsatser vi kommit fram till..

To turn the dairy heifers out on pasture is the most natural way for the cattle to get feed. At the same time it is cheap and if it is right treated a feed of high nutritive value. The problem today is to get dairy heifers to grow enough when they are grazing at natural pasture for the entire summer. Therefore, the opinions differ whether pasture is a resource or a problem. The increasing interest of pasture production is due to the fact that you can receive grants for preserving valuable natural assets and cultural landscape elements in the pasture land. A high grazing pressure is necessary to preserve an open landscape and a great variety of species. In the same time the heifers have to supply their nutritive needs in order to grow and be large enough to show heat and be pregnant in right time to calve with a sufficient body size and at an economically right age. This paper includes a literature review on natural pasture, pasture production, and growth of dairy heifers together with own interviews with dairy farmers about their point of view to the pasture husbandry on the farms, how they plan for pasture, look after natural pasture, treatment areas and take care of the calves and heifers. The results indicate that the time it takes and the demanded work are the biggest factors to how and why the farmers do as they do..

Title in original language: Föreställningar om stadsomvandlingens KirunaLanguage of text: swedishNumber of pages: 106.

District heating covers around 80 % of the heating demand in apartment buildings and 10 % in single-family homes in Sweden. In the year 2010 the total input of energy to the Swedish district heating grids was about 70 TWh, which corresponds to 11 % of the total energy input to the whole energy system in the country. Through the combined production of heat and power the CHP-plants often reaches an efficiency of 90 % from energy in the fuel to produced heat and power. In order to keep the efficiency high it is important for the owners of the plant to have good knowledge about the plants performance at different operation points. Strängnäs Energi AB initiated this diploma work together with FVB Sverige ab in order to come up with a program for short term planning of the production of heat and power at the company´s CHP-plant.The work consists of three main parts.

During springterm 2010 Erik Persson and Magnus Hansson performed their ThesisWork with DIAB Laholm, in Hallands County for University of Halmstad.The project has been a product development project without exterior customers. Thusit had a great emphasis on functionality and less emphasis on marketing and such.This reflects the ambition to develop machinery to be used within the productionfacilities of DIAB Laholm, not to be sold to exterior customers.Main objective has been to create machinery which enables the production ofrotational symmetric work pieces within a NC-milling machine with 5 axles. Thework pieces milled will be made of DIAB?s material Divyncell with varyingdensities.The project has followed Fredy Olssons method involving Principal ? Primary ?Manufacturing constructions. However a complete manufacturing construction hasnot been made since DIAB just wanted a good Primary construction which will serveas a base for finishing touches at DIAB.By the end of the project material including calculations has been sent to DIAB andthey will finish the work and manufacture the machine if they find economic viabilityin this.The work method has been suited for this by several reasons, it was created withthese projects in mind and it?s also the method most familiar to us..

As a small and land scarce country, effective waste management is ofoutmost importance in Singapore. In this study the production of biogasthrough anaerobic digestion from the organic fraction of municipal solidwaste (OFMSW) was compared to incineration of the waste. At the momentalmost all of the OFMSW in Singapore is incinerated. Three differentscenarios were compared to the reference scenario (incineration): one with alarge scale biogas plant that can treat half of all OFMSW in Singapore, onewith a medium scale biogas plant about 15 times smaller than the large oneand one with a small scale biogas plant that can treat waste from e.g. ashopping center or a food center.By using life cycle assessment (LCA) the different scenarios were comparedin terms of global warming potential (GWP), acidification, eutrophication,energy use and land use.

Background: The global responsibility for multinational companies is a current matter of subject. Now when the world increasingly is getting globalized, economic growth is created, which brings a bigger demand of responsibility on companies. The leading companies from every industry is often becoming the frame for how the production process works and is therefore exposed to outer pressure which, for example, is coming from consumers and the media. Since consumers at present are more aware of what they are buying and where it comes from, it is important that the companies take social responsibility. We have therefore studied three big companies within the clothing industry to see in witch way they are taking their social responsibility.Purpose: Our purpose was to explore how companies within the clothing industry describe their work with Corporate Social Responsibility, code of conducts and where the incentive behind this work is coming from.Method: We have, through a qualitative study, examined how three large companies work with Corporate Social Responsibility.

The purpose of the project was to exam steams ability to sterilize carrots infected withLactobacillus plantarum. The project was a cowork with Brämhults Juice AB. They hadobserved an increase of Lactobacillus in the production of carrot juice during the summer. Tokeep the flavour of fresh fruits, the juice is treated carefully with heat. This means that thejuice only stays fresh for a few days, around two weeks for an unopened package and threedays for an opened package.In an attempt to remove the remaining Lactobacillus of the carrots, steam is tested as an extrastep in the production of juice.

In Uppsala CHP Plant, there are six pressure reducing valves to reduce the pressure from 15 to 3 bars, before six absorption heat pumps. During the process the energy is conserved but losses occur in form of exergy. The aim of this thesis is to reduce the losses of exergy. This can be done by letting turbines replace the pressure reducing valves.In this thesis an investigation has been done of the conditions today, the conditions after the change from pressure reducing valves to turbines and a comparison of three different types of turbine solutions. The three examined solutions are one turbine, several helical screw expanders and several small turbines in parallel with asynchronous generators.The six absorption heat pumps have been divided into two groups; one group of four and one group of two absorption heat pumps.

Hälso- och sjukvården har höga krav som branschen har svårt att uppfylla. Logistik har fått en ökad betydelse inom sektorn och handlar i detta fall om att på kortast tid få en patient färdigbehandlad. Denna rapport tar fram logistiska förändringsprinciper som är framgångsrika i hälso- och sjukvården. En litteraturstudie visar att det finns ett antal logistiska förändringsprinciper och verktyg som med positivt resultat har anpassats till hälso- och sjukvården. Dessa är; Lean production, processorientering, flödesorientering, Time-based competition, Theory of Constraints, Supply chain management, Planering, Mål och mätmetoder, Patienten i fokus, Genombrott och Advanced access.

Cassava (Manihot esculenta Crantz) is a root crop that plays an important role in many households in Africa. It is sometimes called ?Africa´s food insurance?. The advantages with the crop are that cassava is drought-resistant and it can grow in a semi-dry land. It is a perennial crop and does not require much labor.

In recent years the construction industry has been exposed to increased time pressure which has resulted in a higher amount of wastage. Today 35 % of all construction projects in Sweden is "wasted". Time pressure has risen due to increased competition on the market, with more actors entering the construction business, therefore profit margins decreased which has led to a more pressing need for decreasing the amount of wastage.Bravida is Scandinavia's largest supplier of installations and provides specialist services in electrical installations (heating and sanitation), and ventilation. Mahdi Bawaqneh's task was to investigate where, how and why wastage occurs in the company's projects and how to prevent such wastage. The thesis covers the subjects of lean production, communication in projects and planning of projects.