Vid användande av polymerer och elastomerer i konstruktioner, lämnar leverantörer oftast endast materialparametrar i form av ett hårdhetstal. De vanligaste provningsmetoderna för hårdhetsmätning av polymerer och elastomerer är Shore samt IRHD (International Rubber Hardness Degree). Hårdhetstalen som erhålls är svåra att använda i Finita Elementanalyser, då de ej direkt kan översättas till mer lätthanterliga storheter. Syftet med examensarbetet är att utveckla en metod för att omvandla hårdhetstal till användbara Finita Elementstorheter. Det finns flera olika metoder för hårdhetsmätning inom Shore och IRHD.Arbetet begränsades dock till att enbart täcka en metod för Shore samt två metoder för IRHD.

With a growing population on earth the amount of end-of-life vehicles (ELVs) and other scrap steel increases. The European Directive 2000/53/CE? requires a minimum of 95 % reuse and recovery and 85 % re-use and recycling no later than 1 January 2015, for end-of life vehicles. This imposes a need for more efficient recycling and recovery. Despite this shredder residue (SR) is commonly land filled.This report investigated the magnetic fines residue generated at Stena Metall shredder facility in Halmstad, Sweden.

When stormwater occurs near human activity the water gets polluted. The purity and composition vary widely depending on the types of activities in the area, the type of surface the water comes in contact with, precipitation and many more parameters. It has long been known that stormwater quality can affect both human health and the environment as stormwater is a major contributor to pollution of receiving waters.A human activity that has an impact on the environment in several different ways is traffic and stormwater is no exception. Airborne gases that react with precipitation, oil leaks and fuel systems that drops down on the ground, metals from brake linings and rubber particles from tire wear are some of the aspects you have to take into account when categorizing the relationship between traffic and polluted stormwater.In this project, stormwater samples from a parking lot in Halmstad, Sweden were collected and analyzed with an atomic spectrophotometer. The presence and relationship between copper, cadmium and zinc with different rainfall parameters have been studied.

Compressed air is an energy source that is widely used in today's trucks and buses.Compressor located next to the engine supplies the pneumatic system with the compressed air and is lubricated with the engine oil. Some of the oil follows the air flow in both liquid and solid phase. The solid phase, namely the carbon particles are created due to the high temperature in the compression chamber.Oil- and particles carryover softens and destroys the rubber material in the air valves and disturbs the mechanical function of various components in the pneumatic system. In order to reduce oil- and particles carryover is an Air Processing System (APS) set downstream the compressor.No method for establishment of oil- and particles carryover from the compressor exists at the moment. Therefore the filtration efficiency of APS is currently unknown.

With a growing population on earth the amount of end-of-life vehicles (ELVs) and other scrap steel increases. The European Directive 2000/53/CE? requires a minimum of 95 % reuse and recovery and 85 % re-use and recycling no later than 1 January 2015, for end-of life vehicles. This imposes a need for more efficient recycling and recovery. Despite this shredder residue (SR) is commonly land filled.This report investigated the magnetic fines residue generated at Stena Metall shredder facility in Halmstad, Sweden.

Examensarbetet har utförts vid ABB Power Transformers i Ludvika i plåtverkstaden, där stora transformatorlådor svetsas ihop. Tillsammans med vår handledare på företaget utformades ämnet för examensarbetet att bedöma luftkvalitet och arbetsmiljö vid punktsvetsning i koppar. Det fanns misstanke om att exponeringen för koppar var hög och en utvärdering av luftkvaliteten behövde därmed göras. Ingen tidigare exponeringsmätning vid svetsning i koppar har genomförts i plåtverkstaden. Syftet med examensarbetet var att utvärdera och komma fram till tre åtgärdsförslag för att skapa en bättre arbetsmiljö vid punktsvetsning samt att begränsa exponeringen av svetsrök som bildas vid svetsning i koppar. Tre åtgärder var företagets önskemål.

This thesis is about developing a design that provides improved vacuum seal between a lead coating and a plastic coating during plastic extrusion processes of cables. This report is a part of the course MSGC 17 for Bachelor Engineers in mechanical engineering.The work is performed at Nexans Norway AS in Halden where they have a production of high voltage cables for sea-, and offshore industry. A problem they face is that they do not get enough good seal at the attachment to the plastic extrusion machine. They want to achieve a vacuum between a lead coating on the cable and a plastic coating of the cable for plastic extrusion, which is something they do not achieve today. The thesis is thus to come up with a design that provides better sealing against the cable.The work involves a construction part with the phases of product development processes.

Since the Human Immunodeficiency Virus (HIV) that causes Acquired Immune Deficiency Syndrome (AIDS) was discovered in the 1980s, the condom has scientifically proven to be the only technological device that can prevent transmission of the virus during sexual intercourse. This technical approach to the HIV has strongly emphasized that prevention is only possible if the condom is properly used. However, as a technological artifact the condom has shown that its use is laden with values. The question of values on condoms has brought in a heated debate on the moral justifications of its use. In Malawi, just as in other African countries, the Faith Community has rejected the Governmentsplea to promote condoms as the preventive measure against the virus.The Faith Community has emphasized on abstinence and mutual faithfulness as the only reliable means to the prevention of HIV/AIDS.

When performing studies that test the reactions of horses in different situations, important information may be available about the horse?s reactivity level. With information from these tests, accidents and dangerous situations may be prevented. When the behaviours from tests are compared with race performance it may be possible to evaluate if some behaviours are more desirable at the race track than others. The aim of this study was to see if behavioural responses correlated with physiological parameters (heart rate, cortisol), the trainer?s opinions and actual race performance.

BAE Systems Hägglunds has a long history of producing high performance terrain tracked vehicles (mostly for military applications), and they are now aiming at developing a tracked forwarder with similar techniques.The forwarder will be of series hybrid type where a diesel engine via a generator will power the motors (one for each drive wheel). Thanks to individually controlled motors and the gentle rubber tracks, this forwarder is calculated to have a considerably higher average speed in the terrain and to be more gentle to the soil. The forwarder with a weight of 11 metric tons and a load capacity of 15 metric tons is specified to have an average working speed of 7-10 km/h, a top speed in terrain of 15 km/h and a top speed on roads of 40 km/h.This master?s thesis aims at developing a conceptual design of the forwarder?s drive module which includes electric motor, gear unit, brake and drive wheel.To investigate if the requirements can be fulfilled a study of the dimensioning loading scenarios has been carried out. The resulting needs regarding the torque has been considered in order to determine the required gear ratios for different motor options.

Denna avhandling avser produktutvecklingsprocessen för ett upphängningssystem tillhörande ett banddrivet fordon. Syftet med systemet är att tillåta fordonet nå högre hastigheter. Det ska också tillåta dämpning och viss nivellering vid körning i kuperad terräng. På så sätt blir fordonet smidigare och föraren utsätts för mindre helkroppsvibrationer.I samarbete med forsknings- och utvecklingsavdelningen på BAE Systems Hägglunds AB genererades ett antal koncept på upphängningssystemet. Genom att använda listan av produktspecifikationer som BAE Systems tidigare tagit fram tillsammans med exempelprocessen beskriven i Product Design and Development valdes ett koncept att analysera mer detaljerat.

Since the 1980s, companies have taken a larger interest in quality and it´s economic impact within the company. Having the knowledge that it´s not quality that costs money, but it´s rather the lack of quality. The work immerses itself in the field of cost of poor quality and the development of key performance indicators.The thesis is performed at Bufab Holding in Värnamo. Bufab Holding is a trading company which mainly buys and sells C-parts. C-parts include fasteners, other small metal-, rubber- or plastic parts such as wires, springs and electronic fasteners.The aim of this thesis was to make a survey of the cost of poor quality and to find key performance indicators (KPI) for cost of poor quality that can be continuously monitored.

Examensarbetet har varit förlagt på SwePart Transmission AB i Liatorp. Företaget tillverkar kugghjul och kan även ge helhetslösningar för växellådor. SwePart Transmission AB har uppmärksammat problem i form av läckage vid delningsplanet i sina växellådor. Företaget har föraningar om att konstruktionen utsätts för glidning i delningsplanet där packningen är placerad. För att glidning inte ska förekomma krävs att packningens friktionskoefficient och fästelementens förspänningsförluster är kända vid konstruktionsstadiet.Packningens friktionskoefficient är idag osäker och har kontrollerats.

In Sweden today many municipalities and sport clubs chooses to build artificial turfs becauseof the increased period of using the turfs during the year and less maintenance requirementsthan for natural grass fields. What could be problematic with artificial turfs is the rubbergranules used as infill material in the turf matt. The rubber granules are often made fromrecycled tires, which may contain for the human health and the environment, harmful substances.This was the reason why the Swedish Chemicals Agency commissioned a statusreport in 2006 which, among other things, concluded that the environmental and health risksassociated with granules made from recycled tiers in artificial turf fields were small, but thatthere could be a local environmental hazard. The purpose and objective of the risk assessmentwas to identify how artificial turf plans granules can affect recipients in the area closeto the pitches and provide input to reduce the spread of metals and substances harmful forboth human health and the surrounding environment. The work was divided into three parts:(1) the construction of artificial turf pitches and their material content, the spread of granulatesoutside the fields and disposal of artificial turf pitches.

Detta examensarbete handlar om utveckling och konstruktion av ett spjäll och spjällblad till en plattvärmeväxlare som ingår i Fläkt Woods AB:s produktsortiment.Bakgrunden till utvecklingen berodde på två problem med det nuvarande spjället. Ett problem var att det fanns vissa hygienproblem med befintlig konstruktion som behövde rättas till och ersättas mot en bättre lösning. Detta för att produkten ska kunna certifieras enligt normen VDI 6022. Det andra problemet var att den befintliga konstruktionen kändes gammal och behövde förbättras.Examensarbetet omfattar två stycken huvuddelar/mål. Den första delen är att finna ett material för att kunna täta i spjället på ett effektivt sätt.