Companies acquiring ERP systems are often dissatisfied with the project and therefore consultancy firms wish to make use of project models in order to achieve success in implementations. Since research on ERP implementations in service companies is limited, there is a need for mapping of critical activities in implementation projects in this line of business. Under these premises, the purpose of our master thesis is to develop a model for implementation of ERP systems, specified in activities, which can be used by mid-sized consultancy firms with mid-sized qualified service companies as customers.A literature study including project models, modern models and methodologies for ERP implementation, commonly existent activities, success factors and system development methods was carried out. Starting out with this, a theoretical model for ERP implementation was generated. In excess of this, a case study was conducted, where the implementation of the ERP system Microsoft Dynamics AX at the service company Eurostep, performed by the consultancy firm Medius, was studied.

In this project the focus has been on the system for recombination at Oskarshamn 2. The recombining systems have on several occasions switched paths due to low pressure before the last ejector that?s feeding the recombiner. Of the mentioned reason, events and several measuring points have been analyzed in this report since the installation of the recombining systems.In order to prove theories and demonstrate what may be the cause of this problem, we used heat balance calculations by the program Probera. Using the program, we can demonstrate that the catalytic process does not reach the desired temperature with the amount of combustible substance.

The purpose of this bachelor thesis is to examine the similarities and differences between best practice literature regarding digitization and an existing cultural heritage digitization project. It also aims to determine whether this literature is of any help during an actual project of digitization. These results were achieved by examining literature regarding best practices in digitization and analyzing how well an actual project correlates to this advice. The information about the Digidaily project was obtained through two qualitative interviews as well as the project blog. The outcome of our research showed that although there are a great many similarities between theory and practice, the project in question was not helped by literature.

The division of Electricity at Uppsala University runs a project called Lysekil project, they have designed a buoy that uses the waves to create electric power from a generator attached to the bottom of the sea.Uppsala University is closely connected with the company Seabased and the university makes use of their facilities in Lysekil. When they designed the buoy issues occurred, the geometric design was flawed, brackets with a short shelf life and it is generally uneconomic.A study visit was done in Lysekil on Seabased facility. With this visit the project started, which is to improve the design of the buoy and the attachment of wires leading to the generator. In this project we have chosen to use a beam system with three beams that are attached to the buoy. Then a wire attached to a plate that sits between the beams will be leading to the generator. Two proposals for construction are created, what distinguishes them are the brackets between the beams and the buoy.From these constructions, the design that is considered most optimal for our project is chosen.All parts of the buoy have been modeled and the drawings are designed in ProEngineer software.The two constructions are compared with each other, but the whole focus is on the second and final structure. The report begins with an introduction describing Lysekil project, and a task description of our project.The project aims to produce an optimal buoy that will be easy to design, materials restrictive with good durability and an economical solution.Wave power true function has been studied, mechanical and finite element analysis of beams, buoy and plate design.This has been presented in this report, where in the various chapters can read more about the processes. Although the relevant facts and information on this project and buoy development is included.

The objective of this project was to develop an application for mobile phones using the Android operating system. The main goal was, with the help of GPS, to pinpoint locations, measure distance traveled and illustrate the progress on a map. Functionalities for just showing the map, fetching addresses and saving to a database was also implemented. The result of the work was a proper application, called MeasureApp, that fulfills the goals set in the planning stages of the project. MeasureApp can be used to measure distances where accuracy is not a main factor, i.e walks or runs.

This exam paper has been a collaboration between the writers and System Anderson AB. The assignment was about completing a client application, running on a PDA, and a server application, running as a web service. The web service handles the communication with System Anderssons existing database. The main goal for the application is that it will be used to increase efficiency in storage management. The client application will hold functions for withdrawal, purchase, delivering and inventory.

The thesis that follows is performed in collaboration with Nitator in Oskarström.The factory in Oskarström focuses on laser cutting, robotic welding and surfacetreatment of steel for the automotive industry.The project aims to streamline the flow of materials in production by automatingthe movements of the forklifts, running to and from the interlayer, and betweenworkstations.The project started with a systematic literature search. The literature searchshowed the research position around the AGV-system. Also a review of studentliterature was made, so that a suitable method for practical implementation couldbe developed and applied. Selected method uses both quantitative and qualitativeapproaches, which is analyzed by using triangulation.The work has resulted in a modified layout of the current facility in Oskarströmthat can be used for the implementation of the AGV-system. It has also resulted inthe tender documents and profitability calculation from several of AGV-suppliers..

This report describes the process of translating Russian financial information in accordance with Russian Accounting Standards to IFRS, International Financial Reporting Standards. The author describes the two regulatory frameworks and reveals a number of risk factors in the process. These risk factors may affect the reliability of figures from Russian companies. The conclusion states some recommendations on how these risk factors can be managed..

The purpose of this project is to analyze earthing systems for houses. By practical measurements and theoretical analyzes consequences of possible faults, that can occur within the facility and in the low-voltage distribution network, is illustrated.  The reason for this project is that nowadays one has to arrange with a main equipotential bonding system for buildings. Apart from that, if necessary, bathrooms must be provided with a supplementary equipotential bonding system.The practical measurements verify that potential differences in facilities may be due to voltage drops in the PEN conductor between the origin of the electrical installation and the power transformer.Based on the theoretical analyzes of possible faults, it is considered that the requirement for  supplementary equipotential bonding systems for bathrooms in most cases can be questioned, when basic insulation, fault protection, residual current devise and main equipotential bonding system already provides an adequate level of protection.A PEN conductor loss may result in a situation where metallic parts attached to the equipotential bonding system starts working as earth electrodes. Equipotential bonding system may also increase the incidence of stray currents. If TN-C-S systems is provided with a local connection to earth a redundant system against PEN conductor loss is obtained.

AbstractIn the fall of 2003 a project was started in the Swedish building sector that is called BASTA (the building sectors’ termination of especially harmful substances). The project is operated by the building companies NCC, Skanska, PEAB and JM, the Swedish Building Industry and the Swedish Environmental Institute IVL. The purpose of the project is to create a common environmental assessment system for the entire building industry and with the help of this system phase out the use of especially harmful properties from building products.In a large sense BASTA works like this; On the BASTA web site there is a database, to which a supplier can register the company and the company’s products. Only those products with a substance content that fulfil the demands of the BASTA system, is to be registered. As it is the supplier himself that carries out the registration of the company and the company’s products to the system, the BASTA-organisation annually controls that the companies that are registered in the database, fulfils BASTA’s demands.Since NCC is one of the companies that operates BASTA, BASTA is probably going to be the environmental assessment system that is recommended for the company in the future.

BackgroundA cost that lately has been discussed related to audit is the higher cost for auditing of small stock company. The question is if this cost is higher than the total utility of statutory audit and should it in that case be statutory. SRF says that the condition for small stock companies development is an abolishment of statutory audit. FAR consider that auditing is important for development and continuation.PurposeThe purpose of this paper is to investigate whether there are any winners or losers among auditing firms and accounting firms in Sweden if the statutory audit for small stock companies abolish.MethodThe paper is both a qualitative and a quantitative study that is based on primary data made from an interview and a questionnaire investigation. ConclusionOur conclusion is that the big Winner is the accounting trade.

The division of Engineering Materials at Linköping University, department of Management and Engineering, conducted a research project concerning Fatigue life of thermal barrier coatings during 2009. During this project equipment to provoke these fatigue failure by rapidly heating and cooling test subjects in cycles, was ordered.Design and manufacturing of the equipment was handled internally at LIU.The equipment was built using a furnace that is lowered and raised over the table where the test subject is placed. To keep the temperature of the furnace a lid slides in place to close the downward facing opening of the furnace when it is in the raised position. On this door there is nozzle that is used to cooling of the test subject by air.To make sure that the equipment can work independently you need an automation controller that can evaluate if movement can occur without danger of collisions. The control system also needs to monitor that all elements are performed according to plan.This degree project is based on a modular system from OPTO 22 and includes the configuration of a PLC that will be supplied with logic and a user interface.The degree project resulted in a graphic interface in which a user can set desired values for different parameters and get information about current values for them.

Earlier models that measured de facto harmonization of international accounting mainly used indices and other related statistical models. Those approaches do not account for the relative importance of individual balance sheet items or expense items being harmonized. This paper therefore proposes a different approach using Runsten?s (1998) permanent measurement bias model. That way it is possible to quantify the harmonization process by accounting for differences among companies.

The objective of this project was to develop an application for mobile phones using the Android operating system. The main goal was, with the help of GPS, to pinpoint locations, measure distance traveled and illustrate the progress on a map. Functionalities for just showing the map, fetching addresses and saving to a database was also implemented. The result of the work was a proper application, called MeasureApp, that fulfills the goals set in the planning stages of the project. MeasureApp can be used to measure distances where accuracy is not a main factor, i.e walks or runs.

Title: Have IFRS made the accounting more efficient for investors? ? A study of goodwill-relevance Level: Final assignment for Degree of Master (One Year)Author: Patrik Nygard and Andreas Pettersson       Supervisor: Markku Penttinen            Date: 2010 ? MayAim: The Swedish banks SEB and Swedbank are on the same market but their goodwill is amortized totally differently and its results will be different. We decided to examine the accounts in Sweden and see if they have been more efficient, from a user perspective, after the introduction of IFRS in year 2005Method:  This paper is made from a quantitative and a deductive approach. We have collected data from all companies listed on the Stockholm Stock Exchange between the years 2002-2008 using the computer program Financial Datastream and then made the regression and other analyses and comparisons with the program MinitabResult & Conclusions: We have in this paper demonstrated that how the accounting of goodwill designed is relevant to investors and that this relevance has increased in Sweden after the transition to IFRS. We have also concluded that the goodwill has greater relevance in a rising market than in a downward.Suggestions for future research: In future researches can the aim be to compare other accounting standards changes that occurred in the year 2005 and see if the accounting, from that perspective been more efficient.Contribution of the thesis: We have shown how the account influences investor?s decisions during different accounting systems and in particular how they react on the changed account of goodwill.