When models are used to describe physical phenomenon during development or modification of a technical system, it is often possible to reduce both the time needed and the overall development cost. With the use of models it is also possible to investigate the potential of the selected solution, without the need for any expensive details and testrigs. In many cases it is also not possible to test all the aspects regarding the functionality that are desired from the system, without using the complete and final product.In this case a model based approach has been used to optimize the different parameters in the new snubbing mechanism for the Nose Landing Gear Retract Actuator on the JAS39 Gripen.During the simulations, upper and lower boundaries were calculated for the length of the spring and the diameter for the restrictor. The governing constraints were given by the requirements for the retraction time during cold conditions and that the amplitude of the alternating loads in the uplock mechanism were brought to an acceptable level.The most promising results from the simulations were then used in a limited number of trials in the hydraulic rig to verify that the configurations comply with the requirements.The final parameters for the snubbing mechanism were chosen to 35±1mm for the spring and 0.4-0.5 mm diameter for the restrictor..

We have been looking at three different types of agriculture in Södermanland, in the middle east of Sweden. We call the different types for Intensive, Extensive and Mix. The purpose is to get an economic defensible plan for how to run different farm sizes. We also have been looking at the working hours and how many hours the different types will give. We have a farm called Taxinge Gods as our pilot farm. Taxinge Gods grow 407 ha land and is located 60 km southwest from Stockholm.

This report provides a comparison between the products cellular concrete, foam concrete and LECA concrete. The questions to be answered during the work is how the cellular concrete stands up in cost terms to the existing competitors on the market, how the concrete products differ in design work, and in which situations the concrete varieties are preferred to use.Cellular concrete is a variant of ordinary concrete, with the difference that the ballast is exchanged from stone materials to expanded polystyrene beads (EPS). This substitution gives a product with higher insulation values but lower weight than ordinary concrete.The work was carried out by designing a survey which was sent to two hundred randomly chosen companies across Sweden, to see the building industry?s opinion of the product cellular concrete. The survey showed that cellular concrete was equals its competitors in terms of price, while the product was said to be more flexible, quicker and easier to cast.Then some of the companies, who participated in the survey, were interviewed to see more carefully, how the price, the workmanship and the time for casting and dehydration differed between the products.

I denna studie har vi haft som avsikt att jämföra två modeller som förklarar avkastningen på aktiemarknaden. Modellerna är Capital Asset Pricing Model (CAPM) och Fama-French trefaktormodell(FF3). Undersökningen har gjorts på Nasdaq OMX Nordic Stockholm över perioden 2002 till 2012. Vi har valt att göra denna undersökning för att se huruvida FF3 med två extra faktorer kan förklara avkastningen på aktiemarknaden bättre än CAPM. Sex portföljer konstruerades och vi har visat att FF3 statistiskt signifikant förklarar mer än CAPM för fem av sex portföljer.

Accounting for financial instruments can either be based on a transactions approach or an eco-nomic approach. Under a transactions approach instruments are reported at cost whereas under an economic approach instruments are reported at fair value. Hence, under a transactions approach realization becomes a criterion for recognizing fair value fluctuations as revenue whereas under an economic approach it does not. A mixed model is defined as a combination of the transactions approach and the economic approach insofar it records some accounting items at cost and other items at fair value. The mixed model gives rise to an issue commonly referred to as an accounting mismatch.

ITT Flygt is a world leading company that mainly manufactures submersible pumps. A problem of ITT Flygt is that product development projects rarely manage to hold the estimated project time. It shows that something unexpected occurs in projects quite often, which results in delays. The delays can both be due to an optimistic time plan of projects and risks in product development projects which are not discovered at an early stage. This added with unforeseen delays makes it difficult for ITT Flygt to estimate the duration of their projects.The goal with the Master thesis is to examine a suitable method for simulation of project time.

The purpose of this study has been to examine what it is in the situation that affects which leadership that is applied on the members of the organization. Our questions that we have explored were; What is it in the situation that influences the leadership applied on an individual or staff group? What similarities and differences have emerged by Hersey and Blanchards situational leadership model?Further, we used qualitative semi-structured interviews at the interview procedures with three managers and three employees. Hersey and Blanchards situational leadership model and Goffmans theory in the book "The presentation of self in everyday life" have been used as a foundation and inspiration in this study.We have found that circumstances like the size of the staff group along with the organizations financials and the resources affect the leadership behavior and how well it is matched with the employees. The function of the leaders position in the context, and the purpose of the situation influences how the leadership is formed.

It appears that it has never been easier for the marketer to create and distribute advertising messages. The technical development has created new possible channels, which in addition to the traditional advertising media has resulted in consumers encountering loads of commercial messages every day. Unfortunately for the marketer, the overload of messages has contributed to an extensive advertising avoidance. This forces him to think outside the box in order to come up with attention-grabbing and innovative methods to reach out to consumers. This paper aims to examine if facilities for group exercise classes at fitness centres could be a potential advertising medium due to the unexpectedness of encountering advertising in those premises.

Fuktskador på uteluftsventilerade vindar är ett ökat problem, i det mer miljömedvetna Sverige. Genom tjockare vindsbjälklagsisolering minskar både energiförlusten genom bjälklaget och uppvärmningsbehovet i huset, men hur många funderar på vad som händer med det förändrade klimatet på vinden och hur det kan påverka fuktförhållandena i utsatta delar av konstruktionen.Studier från Chalmers Tekniska Högskola har framställt ett fuktberäkningsprogram för uteluftsventilerade vindar vid namn Simple Cold Attic Model. Programmets funktion och potential har prövats i denna rapport genom en beräkningsanalys av en uteluftsventilerad vindskonstruktion. Försök till att förbättra fuktsäkerheten i konstruktionen har utförts och redovisas i rapporten. Studien har påvisat att den studerade konstruktionen inte är fuktsäker om den uppförs i Stockholmsområdet. Det visades även att aktiva val i konstruktionen kan förebygga fuktskador. Studien har påvisat vikten av inte beräkna med medelår för klimat och hur det påverkar beräkningsresultatet av mögeltillväxt.

Companies worldwide strive to reduce costs and capital tied up in stock. At the same time, the need for short delivery times requires efficient logistic flows. In order to meet customer demands an efficient warehouse activity is required.The purpose of this study is to develop a model for designing a warehouse system regarding to working environment and safety. The model is primarily designed and based on literature reviews of scientific articles and books, own knowledge and the authors previous work experience in the industry.The thesis has been done at Sandvik AB, the department Precision strip in Sandviken. Sandvik is a high-technology engineering group with advanced products and a world-leading positions within selected areas.

This study will shed light on the subject of system management and system management models. It is important that everyone within an administrative organization understand business objectives and needs of the users who work with the systems. It is vital for the activity to form a structured approach for its management, which includes a system management model. Every company has its individual system management model that is tailored to support their management of a business IT systems. According to Brandt (2000), a system management system model is defined as "an idealized image of how you want the system management work is conducted".

This is a dissertation for a Bachelor Degree Project at the University of Skövde. The project is carried out in cooperation with the company Kinnarps AB.The objective of this project was to develop a new chair for café and lunch rooms, which should satisfy the markets expectations and demands and match Kinnarps AB?s assortment today. The project has contained everything from identification of user and customer needs and requirements to evaluation and building of a prototype.The result is a chair with a frame of tubular steel and there is nothing like it in Kinnarps AB?s assortment today.

Laser for material processing possesses a number of advantages which mean that it has been and will be an important component for a wide range of industries' future development. Cutting materials processing is the dominant use of laser technology and has revolutionized the manufacturing industry. The aim of this thesis is to describe the principles of metal cutting by laser, how laser cutting is applied in practice and to identify how Swedish companies are using laser cutting. For the theoretical and technical description of laser cutting literature studies are the primary source of information. The empirical basis for the mapping of the Swedish industry for laser cutting is grounded on a survey; this includes Swedish companies that use laser cutting in their production.

This master?s thesis was performed during the fall of 2006 at Cloetta Fazer AB in Ljungsbro. Cloetta Fazer is the market leader in Scandinavia of manufacturing confectionary and chocolates. The purpose of the project has been to identify causes that impact the quantity of waste in production as well as a cost/benefit analysis of the solutions that can reduce the problem of production waste.The work includes four production lines that are individually designed depending on what kind of product that are produced on the line. By using qualitative and quantitative methods such as focus groups, interviews and observations data has been collected.

Storm water management has become a more important matter as urban areas are expanding and natural areas are being exploited. As nature landscapes are being converted into hard surface areas storm water flow is affected both in terms of velocity and size. A flow increase can easily result in a flooding if the dimensions of the pipeline system are inadequate. Considering predicted upcoming climate changes, flooding?s may become more common in urban areas in the future.